Микроконтроллеры

Товары (19.000+)

DSPIC33FJ12MC202-I/SS - 40 MIPS 16-bit Motor Control DSC | Microchip
DSPIC33FJ12MC202-I/SS

DSPIC33FJ12MC202-I/SS - 40 MIPS 16-bit Motor Control DSC | Microchip

The Microchip Technology DSPIC33FJ12MC202-I/SS is a 16-bit Digital Signal Controller (DSC) engineered for high-performance motor control applications, integrating DSP and MCU functionality on a single die. The device delivers 40 MIPS throughput from a 40 MHz CPU at 3.0-3.6V, includes 12 KB of Flash program memory and 1 KB of RAM, and operates over the industrial -40C to +85C temperature range in a 28-pin SSOP package. A Digital Signal Controller (DSC) is a hybrid architecture that combines a microcontroller's deterministic control peripherals with a digital signal processor's math engine, enabling closed-loop control loops, power-factor correction, and sensorless motor algorithms in a single chip. The dsPIC33F family adds a 16-bit data path with a hardware multiplier and barrel shifter, allowing designers to execute field-oriented control (FOC), space-vector modulation, and digital filtering without offloading to a separate DSP. Key features of the DSPIC33FJ12MC202 include dedicated motor-control peripherals: a 6-channel PWM module with complementary or independent output modes and programmable dead time, a 1.5 Msps 10-bit ADC with up to 8 analog channels, and a 16-bit quadrature encoder interface for position feedback. The part also provides I2C, SPI, and UART/USART connectivity, plus IrDA support, and 21 general-purpose I/O pins. At the silicon level, the device uses separate program and data memory buses (Harvard architecture) so that instruction fetches and data accesses occur in parallel. This eliminates the wait-state penalties common to von Neumann MCUs and is the structural reason dsPIC33F parts can sustain 40 MIPS while executing multiply-accumulate (MAC) operations every instruction cycle. Typical applications include BLDC and PMSM motor drives, sensorless fan and pump controllers, small appliance motor drives, and HVAC damper actuators. The 28-pin SSOP footprint also suits LED lighting drivers and DC-DC converter digital control loops where tight PWM timing is required. When designing with this part, allocate ADC sampling within the PWM cycle to avoid converter noise injection and use the dedicated QEI pins for encoder feedback rather than remapping general-purpose I/O. Brown-out reset and the on-chip LVD ensure deterministic startup under variable supply rails. This page synthesizes distributor pricing, parametric alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
DSPIC33FJ12MC202T-E/ML - 16-bit Motor Control DSC, 12KB Flash | Microchip
DSPIC33FJ12MC202T-E/ML

DSPIC33FJ12MC202T-E/ML - 16-bit Motor Control DSC, 12KB Flash | Microchip

The Microchip DSPIC33FJ12MC202T-E/ML is a 16-bit Digital Signal Controller (DSC) that combines DSP performance with a 16-bit MCU architecture, optimized for motor control applications. Housed in a 28-pin QFN (6x6 mm) package with extended automotive temperature grade (-40C to +125C), it integrates 12KB of Flash program memory, 1024 bytes of SRAM, and 1024 bytes of EEPROM, while supporting operation from 3.0V to 3.6V. The DSC core runs up to 40 MIPS at 3.3V and includes a single-cycle 16x16-bit MAC, dual 40-bit accumulators, and a barrel shifter, enabling precise field-oriented control (FOC) loops. A Digital Signal Controller (DSC) is a hybrid device that merges a microcontroller's deterministic control peripherals with a digital signal processor's arithmetic throughput. Within the broader product hierarchy, the dsPIC33F sits between general-purpose PIC24 MCUs and high-end dsPIC33E DSCs, targeting real-time control loops that demand both fixed-point DSP and deterministic interrupt response - the same hierarchy as DSP > microcontroller > semiconductor. This positions the part above a standard PIC16/PIC18 MCU but below application processors, ideal for sensored and sensorless motor control. Key features include a 6-channel PWM module with complementary outputs and dead-time control, a 10-bit ADC with up to 9 channels and 1.1 Msps conversion rate, three 16-bit timers, and Peripheral Pin Select (PPS) for flexible signal routing. The Motor Control PWM supports edge-aligned, center-aligned, and variable-phase modes, allowing direct driving of three-phase inverter bridges. The nanoWatt power management unit offers Idle, Sleep, and DOZE modes that reduce quiescent current during standby, extending battery life in portable drives. The dsPIC33FJ12MC202 architecture separates program and data memory buses (Harvard) with 24-bit instruction words, allowing simultaneous fetch of opcode and data. The interrupt controller supports up to five priority levels and 65 vectored interrupts, while the JTAG and ICSP interfaces enable in-circuit debug and device programming without external hardware. The QFN-28 package exposes a thermal pad to minimize junction-to-PCB thermal resistance, supporting continuous switching currents typical of 24V brushless DC motor drives. Typical applications include sensorless BLDC/PMSM motor drives, low-voltage fan and pump controllers, small appliance inverters, e-bike controllers, and automotive auxiliary motor drives. The 12KB Flash is sufficient for field-oriented control algorithms with sinusoidal commutation tables, while 1KB SRAM accommodates state observers without external memory expansion. Designers should note that the -E temperature grade qualifies the part for automotive under-hood environments.

Запрос цены Контакты
DSPIC33FJ12MC202T-E/SO - 16-bit DSC, 12KB Flash, 28-SOIC | Microchip
DSPIC33FJ12MC202T-E/SO

DSPIC33FJ12MC202T-E/SO - 16-bit DSC, 12KB Flash, 28-SOIC | Microchip

The Microchip DSPIC33FJ12MC202T-E/SO is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, delivering 40 MIPS performance with 12KB Flash and 1024 bytes of SRAM in a 28-pin SOIC package. The "E" suffix denotes the extended (-40C to +125C) automotive temperature grade, and the "T" suffix indicates Tape & Reel packaging for high-volume assembly. Targeted at motor control and digital power conversion, the device integrates a DSP engine with a high-performance microcontroller architecture optimized for closed-loop control loops. What is a Digital Signal Controller? A Digital Signal Controller (DSC) is a hybrid device that combines the deterministic interrupt response of a microcontroller (MCU) with the computational throughput of a Digital Signal Processor (DSP). The DSC taxonomy flows as: microcontroller < digital signal controller < dsPIC33F family < 16-bit MCU < semiconductor. DSCs are widely used in applications that require single-cycle MAC (multiply-accumulate) operations, hardware PWMs, and fast ADC sampling - exactly what motor control, power conversion, and switch-mode power supplies demand. Key features include a 16-bit data path with single-cycle 40 MIPS throughput, an integrated Motor Control PWM module with up to 6 PWM outputs, a 10-bit ADC capable of up to 1.1 Msps, and the nanoWatt power management suite for sleep currents down to the microamp range. The device is qualified to AEC-Q100 standards, making it suitable for under-hood automotive motor control systems including HVAC blowers, fuel pumps, water pumps, and seat-position actuators. The architecture combines a modified Harvard bus with a single-cycle MAC unit that executes 40 million DSP operations per second, paired with dual-port SRAM and tightly-coupled peripherals. The 28-SOIC footprint exposes three PWM channels, an I2C/SPI/UART set, and a 6-channel 10-bit ADC, allowing designers to build compact BLDC, PMSM, or sensored/stepper motor inverters. Typical applications include brushless DC (BLDC) motor drives, permanent-magnet synchronous motor (PMSM) sensorless control, switched-mode power supplies (SMPS) and uninterruptible power supplies (UPS), HVAC fan control, and small appliance motor inverters. The AEC-Q100 qualification, extended temperature grade, and rich PWM peripheral set make it especially attractive for automotive body electronics and white-goods variable-frequency drives. When designing with the DSPIC33FJ12MC202T-E/SO, ensure the PWM fault input and current-sense ADC channels are prioritized in firmware; the PWM module can trigger the ADC for sub-microsecond current-loop sampling. Use the device's nanoWatt sleep mode to drop quiescent current to a few microamps between motor commands. This page synthesizes distributor pricing, AEC-Q100 qualified drops-in alternatives, and hands-on motor-control design notes not bundled in the manufacturer datasheet, giving engineers a faster path to a production-ready BLDC or PMSM design.

Запрос цены Контакты
DSPIC33FJ12MC202T-I/ML - 16-bit Motor Control DSC, 40MHz, 28-QFN | Microchip
DSPIC33FJ12MC202T-I/ML

DSPIC33FJ12MC202T-I/ML - 16-bit Motor Control DSC, 40MHz, 28-QFN | Microchip

The Microchip Technology DSPIC33FJ12MC202T-I/ML is a 16-bit Digital Signal Controller (DSC) engineered for high-performance, variable-speed motor control applications. Built around the dsPIC33F CPU core, it executes instructions at up to 40 MIPS (40 MHz), combines a hardware multiply-accumulate (MAC) engine, a 40-bit barrel shifter, and a single-cycle 16x16-bit multiplier for deterministic DSP throughput in Field-Oriented Control (FOC) loops. The part integrates 12 KB of Flash program memory, 1 KB of general-purpose SRAM, and is offered here in the 28-lead 6 x 6 mm QFN package with operating temperature range -40 C to +85 C, supplied across a 3.0 V to 3.6 V range. A Digital Signal Controller (DSC) is a hybrid device that fuses the deterministic real-time peripheral set of a microcontroller with the parallel arithmetic paths of a digital signal processor, enabling single-chip implementation of closed-loop motor-control firmware. It sits within a broader hierarchy of motor-control silicon: DSC -> microcontroller -> embedded processor -> semiconductor. The dsPIC33F family targets cost-sensitive motor drive, switching power supply, and inverter applications where 32-bit DSP performance is not essential but bare-metal 16-bit DSP throughput is mandatory. Key features of this 202 variant include one dedicated 6-channel PWM module optimized for 3-phase inverters (complementary outputs with adjustable dead time, hardware fault input), a 10-bit ADC with up to 9 channels and 1.1 Msps throughput, two comparators with programmable references, and the nanoWatt power-management suite offering Idle, Sleep, and Doze modes that drop quiescent current into the microamp range for standby compliance. The architecture's distinguishing trait is hardware DSP assist in a 16-bit MCU price envelope. The 24-bit instruction word, dual 40-bit accumulators, and zero-overhead DO and REPEAT loops let CLOSED-loop control cycles (current loop, speed loop, sensorless observers) fit inside a single PWM period without CPU loading, reducing BOM cost by eliminating an external DSP or FPGA in compact drives such as ceiling fans, pump controllers, and appliance BLDC modules. Typical applications span 3-phase BLDC and PMSM motors in white goods, HVAC blowers, RC hobby ESCs, low-voltage traction controllers, ceiling-fan drivers, small appliance pumps, and Uninterruptible Power Supply (UPS) inverter stages where the single-chip DSC collapses the bill of materials versus two-piece MCU+DSP solutions. The 28-pin QFN gives an extremely compact footprint for space-constrained boards. A first-pass design tip: the PWMin/Comparator/OC fault inputs must be brought out to dedicated PCB traces routed directly from the gate-driver or current-sense network, and the exposed pad must be soldered to a continuous ground pour. Reference the dsPIC33FJ12MC201/202 datasheet for pinout maps and the dsPICDEM MC1 motor-control development board for a vetted peripheral-assignment pattern. This page consolidates distributor pricing, drop-in alternatives drawn from the same Microchip dsPIC33F MC family, and practical hardware design notes not always summarized in the official datasheet.

Запрос цены Контакты
DSPIC33FJ12MC202T-I/SS - 16-Bit 40MIPS Motor Control DSC | Microchip
DSPIC33FJ12MC202T-I/SS

DSPIC33FJ12MC202T-I/SS - 16-Bit 40MIPS Motor Control DSC | Microchip

The Microchip Technology DSPIC33FJ12MC202T-I/SS is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, combining DSP engine throughput with microcontroller peripherals for high-performance motor control. It delivers 40 MIPS at 40 MHz with 12 KB of Flash program memory, 1 KB of SRAM, and 21 general-purpose I/O pins, packaged in a 28-pin SSOP (5.30 mm body width). The integrated DSP engine executes MAC operations in a single cycle, enabling field-oriented control (FOC) loops, sensorless algorithms, and high-bandwidth current regulation. A Digital Signal Controller (DSC) is a hybrid architecture that fuses a deterministic MCU core with the math density of a DSP. In the broader taxonomy, this part is a motor-control-optimized DSC -> 16-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. It fits between pure MCUs (which lack DSP throughput for tight control loops) and full DSPs (which lack general-purpose peripherals for sequencing). The dsPIC33FJ12MC202 places DSP acceleration in front of the MCU bus so that interrupt-driven motor loops can close in microseconds without CPU starvation. Key features of the DSPIC33FJ12MC202T-I/SS include a 6-channel 10-bit/12-bit ADC with up to 1.1 Msps conversion rate, dedicated motor-control PWM with complementary outputs and programmable dead time, a quadrature encoder interface (QEI) for position feedback, and on-chip Flash with self-programming support. The -40C to +85C industrial temperature grade and 3.0 V to 3.6 V supply range suit industrial drives, appliance compressors, and HVAC blowers. Typical applications include BLDC and PMSM motor drives for fans and pumps, sensorless FOC compressors, low-power field-oriented servo drives, ceiling-fan and small-appliance inverter stages, and battery-powered e-mobility controllers where deterministic loop time and DSP MAC throughput minimize torque ripple. Designers should plan for the dedicated motor-control PWM alignment to gate-driver propagation delays and use the QEI peripheral for rotor-position feedback. The 28-SSOP footprint keeps the BOM cost lower than QFN alternatives while still exposing the full motor-control peripheral set. This page synthesizes distributor pricing, drop-in SSOP-28 alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Запрос цены Контакты
DSPIC33FJ16GP101-E/SO - 16 MIPS 16KB Flash DSC, SOIC-18
DSPIC33FJ16GP101-E/SO

DSPIC33FJ16GP101-E/SO - 16 MIPS 16KB Flash DSC, SOIC-18

The Microchip DSPIC33FJ16GP101-E/SO is a 16-bit, 16-MIPS digital signal controller (DSC) built on the dsPIC33F RISC core, integrating 16 KB of Flash program memory and 1 KB of RAM into an 18-pin SOIC W (wide-body) package. Rated for an extended industrial temperature range of -40 °C to +125 °C and supplied from 3.0 V to 3.6 V, the part delivers deterministic signal-processing throughput for closed-loop digital control. In the broader device taxonomy, the DSPIC33FJ16GP101 belongs to the dsPIC33F "GP" (General Purpose) family of Digital Signal Controllers, an intermediate class between traditional 8/16-bit microcontrollers and full Digital Signal Processors (DSPs). DSPs add hardware multiply-accumulate (MAC) units, dual-ported SRAM, and zero-overhead looping to a microcontroller's peripheral set, enabling single-cycle 16x16 MAC operations and on-chip FIR/IIR filter execution without taxing the CPU. The GP sub-family is engineered for general-purpose DSP and high-speed precision digital control, making it useful wherever a closed-loop algorithm must run in real time without an external DSP. Key features include a 40 MHz maximum operating frequency (16 MIPS at FCY = FOSC/2), an enhanced ADC with up to 12-bit resolution and on-chip reference, a motor-control PWM peripheral, I2C, SPI, and UART interfaces, five 16-bit timer/counters, and three external interrupts with two remappable sources. The 5V-tolerant I/Os source/sink 10 mA or 6 mA in standard mode and up to 20 mA in non-standard VOH1 mode, easing direct drive of logic-level circuitry. Typical applications include industrial motor control (BLDC, PMSM, and stepper drives), digital power conversion, sensorless fan and pump controllers, audio processing front-ends, and precision switch-mode power supplies. Automotive-grade (-E) screening and the SOIC-18 footprint also suit AEC-Q100 contexts and through-hole-friendly prototyping. When designing with this part, plan for an external 2.5-3.0 V LDO and a low-ESR decoupling network on VDDCORE. Use ICSP for programming and the device's remappable peripheral pins (RPn) to optimize PCB routing on the small SOIC-18 footprint. This page synthesizes distributor stock, design-in considerations and drop-in alternatives that complement the Microchip datasheet (DS-70000652F).

Запрос цены Контакты
DSPIC33FJ16GP101-E/SS - 16-bit DSC, 16KB Flash, 20-SSOP | Microchip
DSPIC33FJ16GP101-E/SS

DSPIC33FJ16GP101-E/SS - 16-bit DSC, 16KB Flash, 20-SSOP | Microchip

The Microchip Technology DSPIC33FJ16GP101-E/SS is a 16-bit dsPIC33F Digital Signal Controller (DSC) with 16KB Flash program memory, 40 MIPS CPU performance, and a 20-pin SSOP package. It is part of the AEC-Q100 automotive-qualified dsPIC33F family and operates from a 3.0V to 3.6V supply. The device integrates a high-performance DSP-enhanced Harvard architecture CPU with on-chip Flash and SRAM, enabling single-chip embedded control of high-speed precision digital control loops and digital filter algorithms. A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP). It combines deterministic interrupt-driven control logic from MCUs with DSP-style single-cycle MAC operations, making it ideal for closed-loop control applications where latency, throughput, and math precision must be balanced. The dsPIC33F family sits inside the broader 16-bit DSC taxonomy: DSC -> microcontroller -> embedded processor -> semiconductor IC. Engineers choose DSCs when 8-bit MCUs lack throughput for filter math and when full DSPs lack deterministic I/O. Key features include 16KB of Flash program memory organized as 16K x 8, 2KB of SRAM, 21 I/O ports, peripherals such as timers, Input Capture, Output Compare, PWM, UART, SPI, I2C, and a 10/12-bit ADC. The 40 MHz MIPS rating allows deterministic execution of DSP instructions (MAC, ED, AC) in single cycles. The 20-SSOP (5.30 mm body) package is footprint-compatible across the dsPIC33FJ16GP101/102 and dsPIC33FJ32GP101/102/104 families, simplifying PCB reuse between firmware variants. Architecturally, the DSPIC33FJ16GP101 uses a dual-bus Harvard core with separate program and data paths, a hardware multiply-accumulate (MAC) engine, and 40-bit accumulators for fractional signal processing. The 'E' temperature grade extends operating range to -40C to +125C and qualifies the part to AEC-Q100 standards for automotive under-hood and body-electronics applications, while the 'I' grade is rated -40C to +85C. Typical applications include BLDC motor control, automotive sensor conditioning (e.g., wheel speed, throttle position), digital power conversion (PFC, LLC, full-bridge), industrial inverters, HVAC actuators, and general-purpose DSP-filtered sensor signal chains. The combination of Flash-based code storage, AEC-Q100 grade, and small-footprint SSOP is frequently chosen where PCB area is constrained and harsh-environment reliability is required. When designing with this device, ensure the supply rail stays within 3.0V-3.6V, allow 1-2 uF decoupling near VDD/VSS pins, and reserve the ICSP/ICD pins (PGEDx/PGECx) for in-circuit programming. Use the dsPIC33F peripheral library and MPLAB X IDE with the MPLAB Snap, PICkit 4, or ICD 4 debugger. This page synthesizes distributor stock, automotive-grade cross references, and practical design considerations beyond the manufacturer datasheet, including information that helps engineers select between the E (AEC-Q100) and I (industrial) temperature grades.

Запрос цены Контакты
DSPIC33FJ16GP101-I/SS - 16KB Flash 16-bit DSC 32MHz SSOP-20
DSPIC33FJ16GP101-I/SS

DSPIC33FJ16GP101-I/SS - 16KB Flash 16-bit DSC 32MHz SSOP-20

The Microchip Technology DSPIC33FJ16GP101-I/SS is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family that integrates a high-performance DSP engine with a single-cycle 16-bit MCU core, delivering 16 MIPS at 32 MHz while housed in a 20-pin SSOP (5.30 mm body width) package. It features 16 KB of on-chip Flash program memory, 1 KB of SRAM data RAM, and runs from a 3.0 V to 3.6 V (nominal 3.3 V) single supply with an industrial -40 °C to +85 °C operating range. A Digital Signal Controller (DSC) is a hybrid microcontroller/DSP that combines deterministic real-time MCU control with deterministic DSP throughput; in the broader taxonomy it sits between a microcontroller (MCU) and a digital signal processor (DSP), and it belongs to the wider category of embedded microcontrollers (MCUs) within the semiconductor power-management-and-control family. Microchip's dsPIC33F DSCs implement a modified Harvard architecture with a 16-bit data path, a 24-bit instruction word, and an integrated single-cycle MAC unit, allowing one-pass execution of FIR/IIR filters, PID control loops, and high-speed digital control math without off-chip DSP support. Key features of this device include 16 MIPS performance, 16 KB Flash / 1 KB SRAM, 10-bit ADC with 6-channel conversion (six input channels shared with digital I/O), remappable peripherals via Peripheral Pin Select (PPS), a CTMU (Charge Time Measurement Unit), I2C, SPI, UART, four 16-bit timers, and a high-performance PWM block in GP-flavored variants. The MCU also includes a 5-deep hardware stack, a 16x16-bit single-cycle multiplier, and a 40-bit accumulator that supports fractional math essential for closed-loop DSP control. Architecturally the dsPIC33FJ16GP101 uses a pipelined modified-Harvard core running from the internal FRC or an external crystal/clock source, with on-chip regulator providing a low core VDD; the GP101 is the general-purpose variant (whereas MC101 adds dedicated motor-control PWM). The 32 MHz core clock supports both 16 MIPS single-cycle instructions and DSP MAC operations, while hardware-level context stacking and interrupt response below 5 cycles make it well-suited to deterministic real-time control. Typical applications include low-cost digital power conversion, LED lighting control, sensor conditioning, brushed DC and stepper motor control, low-end audio processing, and small appliance controllers. This general-purpose GP101 variant is chosen where motor-control dedicated PWM is not needed; the MC101 sibling is preferred for motor-control specific applications. A key design consideration: place the 10 µF bulk and 0.1 µF decoupling capacitor pair within 5 mm of the VDD/VSS pins, route MCLR with a 10 kΩ pull-up and a 100 nF capacitor for safe reset, and verify ADC accuracy by using independent analog/digital ground planes connected at a single point near the IC. This page synthesizes distributor pricing, drop-in alternative cross-references, and design notes not found in the manufacturer datasheet, providing engineers with a self-contained decision guide for sourcing and replacing the DSPIC33FJ16GP101-I/SS in volume.

Запрос цены Контакты
DSPIC33FJ16GP102-E/SO - 16 MIPS 16KB Flash 28-SOIC DSC | Microchip
DSPIC33FJ16GP102-E/SO

DSPIC33FJ16GP102-E/SO - 16 MIPS 16KB Flash 28-SOIC DSC | Microchip

The Microchip Technology DSPIC33FJ16GP102-E/SO is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, delivering up to 16 MIPS at 40 MHz and integrating 16 KB of Flash program memory with 1 KB of SRAM in a 28-pin SOIC (SO) wide-body package. The device operates from a 3.0 V to 3.6 V supply and offers 21 general-purpose I/O pins, with AEC-Q100 qualification supporting automotive and industrial extended-temperature deployments from -40C to +125C. A Digital Signal Controller is a hybrid microcontroller/DSP architecture that combines a high-performance CPU with deterministic single-cycle MAC DSP operations, peripherals, and memory on a single die. The dsPIC33F family bridges the gap between traditional 8/16-bit MCUs (which lack DSP throughput) and standalone DSPs (which lack on-chip peripherals), enabling embedded designers to run motor control, power conversion, and sensor-fusion algorithms without a second processor. Key features of this part include a C-optimized 16-bit modified Harvard architecture, 16-channel 10-bit ADC with 1.1 Msps throughput, up to six PWM outputs with independent timing, three 16-bit timers, and Peripheral Pin Select (PPS) that remaps most digital peripherals to any digital I/O for flexible PCB layout. Communications peripherals include I2C, SPI, UART with IrDA/LIN support, and the device also integrates a real-time clock, watchdog timer, brown-out reset, and power-on reset. The 16 KB Flash supports self-programming under bootloader control. The architecture uses a 24-bit-wide instruction word with 16-bit data paths, allowing a single device to execute complex digital filters (FIR/IIR), PID loops, and field-oriented control (FOC) routines in real time without off-chip DSP assistance. The integrated DSP engine adds single-cycle MAC, barrel shifter, and saturation logic, making the part well suited to closed-loop control and signal conditioning. Typical applications include BLDC/PMSM motor control, sensorless fan/pump controllers, digital power conversion (PFC, LLC, phase-shift full-bridge), automotive sensor interfaces (TPMS, body controllers), industrial IoT edge nodes, and consumer appliance control. The wide-body 28-SOIC footprint simplifies hand-soldering and rework on through-hole-style prototype boards. Designers should evaluate RAM headroom carefully: 1 KB of SRAM limits table-heavy DSP libraries, and the 10-bit ADC suits precision control but may not be adequate for high-resolution instrumentation. For higher ADC resolution or more memory, upgrade to the dsPIC33FJ32GP104 family. This page synthesizes distributor pricing, parametric drop-in alternatives within the dsPIC33F family, and PCB layout notes derived from the manufacturer datasheet and PIM information sheet.

Запрос цены Контакты
DSPIC33FJ16GP102-E/SP - 16-bit DSC, 16KB Flash, 28-SPDIP | Microchip
DSPIC33FJ16GP102-E/SP

DSPIC33FJ16GP102-E/SP - 16-bit DSC, 16KB Flash, 28-SPDIP | Microchip

The Microchip DSPIC33FJ16GP102-E/SP is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, combining a 16-bit dsPIC MCU core with a DSP engine capable of 16 MIPS performance at 40 MHz maximum clock speed, housed in a 28-pin SPDIP through-hole package. The device integrates 16 KB (16K x 8) of Flash program memory and 1 KB of RAM, making it suitable for closed-loop control and digital filter implementations in cost-sensitive designs. It operates from a 3.0 V to 3.6 V supply and is AEC-Q100 qualified for automotive applications. A Digital Signal Controller (DSC) is a hybrid architecture that merges microcontroller (MCU) deterministic interrupt handling with a Digital Signal Processor (DSP) MAC engine and barrel shifter on the same die. dsPIC33F devices sit at the boundary between 8/16-bit MCUs and dedicated DSPs, executing one instruction per cycle (plus DSP ops) while preserving a familiar peripheral set. They are widely used in motor control, power conversion, and sensor-fusion applications where deterministic execution and signal processing must coexist in a single chip. Key features of the DSPIC33FJ16GP102-E/SP include a 40 MHz internal oscillator with PLL options, four 16-bit timer/counters, multiple PWM modules, a 10-bit A/D converter with up to 6 channels, UART, SPI, and I2C communication peripherals, plus Peripheral Pin Select (PPS) for flexible pin mapping. The device integrates brown-out detect/reset, power-on reset (POR), and a watchdog timer (WDT) for automotive-grade reliability. Its 28-pin SPDIP package simplifies prototyping and breadboard work, which is uncommon for this part class. The architecture uses a Harvard bus with separate program and data paths, a 24-bit instruction word, and a single-cycle MAC unit, enabling efficient execution of FIR/IIR digital filters and PID control loops. The 16 KB Flash allows mid-sized algorithm libraries while retaining spare space for application code, and the 1 KB RAM is sufficient for typical control loops and small data buffers. Typical applications include automotive sensor interfaces, BLDC/PMSM motor control, switching power supply digital control loops, LED lighting controllers, and low-cost consumer appliances. The AEC-Q100 qualification makes it especially attractive for under-hood automotive electronics and harsh-environment industrial control. Designers should note that the 28-SPDIP package requires through-hole PCB assembly, which is uncommon in space-limited boards. The extended (-E) temperature range of -40C to +125C allows deployment in automotive and industrial environments without additional thermal qualification. This page synthesizes distributor pricing, drop-in 28-SPDIP and 28-QFN alternatives from the same dsPIC33FJ family, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
DSPIC33FJ16GP102-I/SO - 16-bit DSC, 16 MIPS, 16KB Flash | Microchip
DSPIC33FJ16GP102-I/SO

DSPIC33FJ16GP102-I/SO - 16-bit DSC, 16 MIPS, 16KB Flash | Microchip

The Microchip DSPIC33FJ16GP102-I/SO is a 16-bit Digital Signal Controller (DSC) combining DSP throughput with MCU peripherals, executing up to 16 MIPS at 32 MHz and integrating 16 KB of Flash program memory with 1 KB of RAM in a 28-pin SOIC (SO) wide-body package. Designed for high-performance yet cost-sensitive embedded control, the dsPIC33FJ16GP102 belongs to the ultra-low-cost "FJ16GP" family and includes Peripheral Pin Select (PPS), which remaps most digital peripherals onto any available I/O pin to ease PCB routing. A Digital Signal Controller (DSC) is a hybrid architecture that merges a modified Harvard MCU core with single-cycle multiply-accumulate (MAC) hardware and DSP-aware addressing modes. In the signal-processing hierarchy it sits between a microcontroller (MCU) and a full digital signal processor (DSP): richer than an MCU because it can close tight sensor and motor-control loops in hardware, lighter than a stand-alone DSP because it still runs C code with conventional peripherals. The dsPIC33F family specifically targets precision real-time control in motor drive, power conversion and sensor-fusion products. Key features of the DSPIC33FJ16GP102-I/SO include a 16-channel 10/12-bit ADC with hardware accumulation and up to 500 ksps conversion rate, three 16-bit timers, an input capture and output compare/PWM block, two UART, one SPI and one I2C interface, plus three external interrupts. The device operates from 3.0 V to 3.6 V (typical 3.3 V), supports industrial -40 °C to +85 °C ambient temperatures in the I-grade, and offers JTAG-based in-circuit debugging through the MPLAB Snap and ICD programmers. Architecturally the device uses a 16-bit modified Harvard core with single-cycle 16×16 MAC, a barrel shifter and dual-bus fetch, plus a fast interrupt controller with hardware-stacked context saving. PPS allows remapping of digital I/O, timers and serial ports to a flexible subset of the 28 pins, while the analog block shares its own dedicated voltage-rail pin pair to minimize digital switching noise coupling. Typical applications include low-cost BLDC and stepper motor drives, digital power conversion (PFC, LLC, full-bridge), sensor signal conditioning, industrial automation and consumer appliance control. In BLDC applications the high-speed ADC, PWM and DSP throughput let the device run field-oriented control (FOC) without an external DSP. When designing with this part, ensure ADC inputs share a clean analog ground island and use PPS to route peripherals only after re-reading the pin-assignment table - peripherals mapped to remappable pads must avoid any pad marked "RPn" that is not driven by the I/O multiplexer. Decouple VDD/VSS with at least one 100 nF plus one 10 µF capacitor placed within 3 mm of the pins. This page synthesizes distributor pricing, parametric cross-references, drop-in alternatives and design notes that complement the manufacturer datasheet.

Запрос цены Контакты
DSPIC33FJ16GP102-I/SP - 16 MIPS 16KB Flash dsPIC DSC | Microchip
DSPIC33FJ16GP102-I/SP

DSPIC33FJ16GP102-I/SP - 16 MIPS 16KB Flash dsPIC DSC | Microchip

The Microchip Technology DSPIC33FJ16GP102-I/SP is a high-performance 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, delivering 16 MIPS throughput at up to 40 MHz in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It integrates 16 KB of Flash program memory, 1 KB of SRAM, 21 general-purpose I/O pins, and a rich peripheral set including multiple PWM modules, a 10-bit ADC, UART/SPI/I2C, timers, and a 16-bit multiply-accumulate (MAC) DSP engine. A Digital Signal Controller (DSC) is a hybrid device combining a microcontroller's control-oriented peripherals with a digital signal processor's computational blocks. In the broader taxonomy, a DSC sits between a microcontroller (MCU) and a full DSP - a microcontroller is optimized for event-driven control logic, a DSP for high-throughput numerical computation, while a DSC like the dsPIC33FJ16GP102 adds single-cycle MAC and barrel-shifter hardware to the MCU core so that closed-loop DSP algorithms (PID, FOC, notch filters, digital filters) can run side-by-side with housekeeping tasks on a single chip. Key features of the DSPIC33FJ16GP102-I/SP include a 16-bit dsPIC30/33 instruction-set architecture with hardware DSP hooks, 10-bit ADC with up to 1.1 Msps conversion rate, two analog comparators, four 16-bit timers (Timer1 can run from a 32 kHz crystal), hardware RTCC, dual 40 MHz PWM channels ideal for switch-mode power conversion, and an operating voltage range of 3.0 V to 3.6 V. The 28-pin SPDIP footprint simplifies prototyping and bench evaluation, supporting both ICSP in-circuit programming and JTAG debugging through Microchip's MPLAB X IDE and XC16 toolchain. Typical applications span digital power conversion, uninterruptible power supplies (UPS), power factor correction, brushless DC (BLDC) and permanent-magnet servo motor control, sensorless motor drives, LED lighting drivers, and industrial automation loops. The combination of 16 MIPS, deterministic interrupt latency, and a hardware MAC makes it well suited to digital control loops that must close every PWM cycle on tighter schedules than a generic MCU allows. When designing with this device, ensure that the input rails remain inside 3.0 V to 3.6 V, decouple VDD/VSS pairs close to the package with 0.1 µF ceramic caps, and reserve one pair of PGECx/PGEDx pins in the PCB layout for ICSP. The 16-bit MAC saturates cleanly at 40 MHz, but sustained numerical work at peak rate still dominates instruction budget - profile before sharing CPU with a USB or graphics stack. This page synthesizes distributor pricing, verified drop-in alternatives (including same-package -I/SP variants from the same family), and practical design notes derived from the manufacturer datasheet and Microchip's cross-reference tooling, going beyond what any single distributor product page publishes.

Запрос цены Контакты
DSPIC33FJ16GP102T-I/ML - 16-bit DSC 32MHz 16KB Flash 28-QFN | Microchip
DSPIC33FJ16GP102T-I/ML

DSPIC33FJ16GP102T-I/ML - 16-bit DSC 32MHz 16KB Flash 28-QFN | Microchip

The Microchip Technology DSPIC33FJ16GP102T-I/ML is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, delivering 16 MIPS performance from a 32 MHz internal oscillator in a compact 28-pin QFN (6x6 mm) package. It integrates 16 KB of program Flash memory, 1 KB of SRAM, and the dsPIC33F enhanced Harvard architecture that combines MCU peripherals with high-performance DSP capabilities such as single-cycle MAC and barrel shifting. A Digital Signal Controller (DSC) is a hybrid device that merges a microcontroller's deterministic control peripherals with a digital signal processor's mathematical throughput. DSCs sit in the silicon hierarchy between a microcontroller (MCU) and a full DSP, occupying the digital controller tier within the broader microcontroller and signal-processing product family. They are typically used where engineers need to execute digital filter algorithms and high-speed precision digital control loops in a single chip without pairing a separate DSP with an MCU. Key features include up to 16 MIPS operation, on-chip 32 MHz oscillator with PLL, hardware multiply-accumulate (MAC) engine, three 16-bit timers, an input capture module, an output compare/PWM module with up to 6 PWM channels, two UART modules, one SPI module, and one I2C module. The controller also integrates a 10-bit A/D converter with up to 6 channels and 500 ksps conversion rate, plus 21 I/O pins. Operating voltage is 3.0 V to 3.6 V with industrial temperature range of -40C to +85C. The architecture pairs a 16-bit data path with a 24-bit instruction word, allowing single-cycle MAC operations and DSP-oriented addressing modes. This makes the device well suited to digital filtering, FFT primitives, sensor fusion, and closed-loop control applications that exceed classic MCU throughput but do not justify a standalone DSP. Built-in peripherals such as the 6-channel PWM, dual UART, and 500 ksps ADC enable direct interface to motors, sensors, and communication busses. Typical applications include BLDC and PMSM motor control, sensorless fan and pump drives, digital power conversion (PFC, LLC, full-bridge), LED lighting control, induction heating, uninterruptible power supplies, and general-purpose DSP-augmented embedded control. Automotive and industrial designers use it for body electronics, HVAC actuators, and small appliance variable-frequency drives. When designing with this part, pay attention to the 28-QFN (6x6) land pattern, ensure the exposed thermal pad is properly soldered to the ground plane for thermal dissipation, and note the I-temp grade (industrial -40C to +85C). Decoupling requires a 0.1 uF ceramic capacitor placed within 3 mm of each power pin and a bulk 10 uF tantalum or ceramic capacitor on the main VDD rail. This page synthesizes distributor pricing, drop-in alternatives within the dsPIC33F family, and practical design notes not found in the manufacturer datasheet alone, giving engineers a one-stop reference for part selection, BOM validation, and PCB layout decisions.

Запрос цены Контакты
DSPIC33FJ16GP102T-I/SS - 16-bit DSC, 16KB Flash, 40MHz | Microchip
DSPIC33FJ16GP102T-I/SS

DSPIC33FJ16GP102T-I/SS - 16-bit DSC, 16KB Flash, 40MHz | Microchip

The Microchip Technology DSPIC33FJ16GP102T-I/SS is a 16-bit Digital Signal Controller (DSC) that combines the simplicity of an MCU with the throughput of a DSP, integrating 16 KB of Flash program memory and 1 KB of RAM in a 28-pin SSOP package. It belongs to the dsPIC33F family and is optimized for digital filter algorithms, high-speed precision digital control loops, and digital audio/speech processing applications. According to the manufacturer datasheet 70000652F, the device executes up to 40 MIPS at a 3.3 V supply across the 3.0-3.6 V operating range. A Digital Signal Controller (DSC) is a hybrid architecture that merges a microcontroller's deterministic interrupt-driven peripherals with a DSP engine's single-cycle MAC (multiply-accumulate) and barrel shifter. In the broader taxonomy, a DSC belongs to microcontrollers -> microprocessors -> embedded controllers -> semiconductors. dsPIC33F DSCs specifically target real-time closed-loop control where the MAC unit performs one 16x16-bit multiplication per cycle, enabling IIR/FIR filters and PID compensators to execute with deterministic timing unavailable on general-purpose MCUs. Key features of the DSPIC33FJ16GP102 include a 16-channel 10/12-bit ADC with on-chip sample-and-hold, up to 21 general-purpose I/O pins, four 16-bit timers, an input capture module, an output compare/PWM module, and three UART/SPI/I2C configurable serial interfaces. The 40 MHz maximum clock speed (10 MIPS effective from 4x PLL) gives it sufficient headroom for closed-loop motor control at moderate PWM frequencies. The Flash-based program memory supports self-programming under software control, enabling in-field firmware updates through the UART bootloader. Architecturally, the DSPIC33FJ16GP102 uses a modified Harvard architecture with separate program and data paths, a 16-bit DSP engine, a 24-bit instruction word, and a barrel shifter for single-cycle normalized shifts. The integrated DSP instructions (ADD/SUB/MAC) operate on 40-bit accumulators to preserve precision during cascaded filter stages. Power management is provided through idle, sleep, and deep-sleep modes with multiple clock sources (FRC, LPRC, HS, XT) selectable via the OSCCON register. Typical applications include BLDC/PMSM sensorless motor control, AC induction motor V/Hz drives, digital power conversion (PFC + LLC), audio effects processing, sensor signal conditioning with on-the-fly filtering, and industrial control loops. The 28-pin SSOP footprint and 3.3 V single supply make it suitable for compact, cost-sensitive industrial modules where a Cortex-M0/M0+ would lack DSP throughput. Companion parts commonly paired with it include the MCP1700 LDO regulator, MCP2551 CAN transceiver, and MCP4725 DAC for analog outputs in control applications. When designing with the DSPIC33FJ16GP102, ensure that VDD decoupling uses a 100 nF ceramic capacitor within 5 mm of each VDD pin and a 10 uF bulk capacitor near the ICSP/VPP rail. Programming can be performed with the MPLAB Snap, PICkit 4, or MPLAB ICD 4 over the 4-wire ICSP interface (PGECx/PGEDx). Designers migrating from PIC24F to dsPIC33F gain access to single-cycle MAC and DSP intrinsics without changing the development toolchain. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты
DSPIC33FJ16GP304-E/ML - 16-Bit DSC, 40 MIPS, 16KB Flash | Microchip
DSPIC33FJ16GP304-E/ML

DSPIC33FJ16GP304-E/ML - 16-Bit DSC, 40 MIPS, 16KB Flash | Microchip

The Microchip Technology DSPIC33FJ16GP304-E/ML is a high-performance 16-bit Digital Signal Controller (DSC) that combines the DSP engine of a dsPIC with the simplicity of a PIC microcontroller, operating up to 40 MIPS with 16 KB of Flash program memory and 2 KB of RAM in a 44-pin QFN (ML) package. A Digital Signal Controller (DSC) is a hybrid device that merges a microcontroller's deterministic control peripherals (timers, I/O, communication ports, ADC) with a single-cycle DSP MAC engine for real-time signal processing. Within the Microchip taxonomy the DSPIC33FJ16GP304-E/ML belongs to the dsPIC33F "General Purpose" family (FJ series), which sits between the PIC24 16-bit MCU family and the dsPIC33E "Enhanced" DSC family. This positions it as a cost-effective entry point for designers who need DSP throughput (40 MIPS, single-cycle 16x16 MAC) without paying for the larger Flash and richer peripherals of the EP/GS families. Key features of the DSPIC33FJ16GP304-E/ML include 21 general-purpose I/O pins, four 16-bit timers, an enhanced CAN 2.0B module, two UART modules, two SPI modules, two I2C modules, an 8-channel 10-bit ADC (with 1.1 Msps conversion rate), and a dedicated 16-bit motor-control PWM module. The on-chip DSP engine performs single-cycle multiply-accumulate (MAC) operations, enabling real-time digital filtering, FFT, audio processing, and closed-loop control algorithms. JTAG/ICSP in-circuit debugging is supported. The DSPIC33FJ16GP304-E/ML is fabricated on a 3.3V CMOS process, operates from 3.0V to 3.6V supply, and supports industrial-grade -40C to +125C ambient temperature (the "E" suffix indicates the Extended temperature grade; the standard "I" grade covers -40C to +85C). The 44-pin QFN (ML) package with exposed pad provides low thermal resistance for high-IO-count designs in space-constrained applications. Typical applications include sensorless BLDC motor control, field-oriented control (FOC) of PMSM motors, audio/effects processing (reverb, EQ, noise cancellation), digital power conversion (SMPS control loops), industrial sensor signal conditioning (vibration analysis, strain gauge), and automotive body electronics (CAN nodes, HVAC actuators). The integrated CAN 2.0B peripheral specifically targets vehicle networks and industrial automation. When designing with the DSPIC33FJ16GP304-E/ML, observe the device's 3.3V supply requirement: the I/O are NOT 5V-tolerant. Use a level shifter (e.g. TXS0108E) when interfacing to 5V peripherals. Place a 10uF + 0.1uF decoupling pair close to every VDD/VDDC pin pair and connect the exposed thermal pad (EP) to a solid ground plane to minimize the package's 32 C/W theta_JA. This page synthesizes distributor pricing, AEC-Q100 grade availability, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - cross-referenced against the official dsPIC33FJ32GP202/204/dsPIC33FJ16GP304 family data sheet.

Запрос цены Контакты
DSPIC33FJ16GP304-E/PT - 16-bit DSC, 40 MIPS, 16KB Flash | Microchip
DSPIC33FJ16GP304-E/PT

DSPIC33FJ16GP304-E/PT - 16-bit DSC, 40 MIPS, 16KB Flash | Microchip

The Microchip Technology DSPIC33FJ16GP304-E/PT is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F General Purpose family, featuring a 40 MIPS execution speed with integrated DSP engine and a 16 KB Flash program memory in a 44-pin TQFP (PT) package. The "E" suffix designates the extended (-40C to +125C) operating temperature range, making it qualified for harsh industrial and automotive under-hood environments. The "GP" device class targets general-purpose motor control and digital power conversion, while the "304" pin-count variant provides 35 I/O, two UART, two SPI, one I2C, one input capture, one output compare/PWM, and a 10-bit 1.1 Msps ADC with up to 13 input channels. A Digital Signal Controller (DSC) is a hybrid MCU/DSP architecture that combines the deterministic interrupt-driven control of a microcontroller with the deterministic single-cycle MAC throughput of a digital signal processor. Within the broader hierarchy, a DSC sits between a microcontroller (MCU) and a digital signal processor (DSP) in the embedded-processing taxonomy: DSC -> MCU -> embedded processor -> semiconductor. The dsPIC33F family is Microchip's 3.3 V 16-bit DSC line, offering seamless migration from the 5 V dsPIC30F family and from the PIC24F MCU family, sharing the same instruction set and peripheral library for code portability. Key features include a modified Harvard architecture with 16-bit data path and 24-bit instructions, a hardware DSP engine with dual 40-bit accumulators and single-cycle 16x16 MAC, and an integrated 2.5% internal oscillator for reducing BOM cost. The device offers five 16-bit timer/counters, an 8-channel DMA controller for zero-overhead data movement, and on-chip 2 KB SRAM plus 1 KB data EEPROM for parameter storage. JTAG and ICSP programming/debug interfaces are supported, with multiple PGECx/PGEDx pin pairs for flexible PCB routing. Typical applications include sensorless BLDC/PMSM motor control (FOC algorithm fits within the 16 KB Flash), digital UPS and PFC power conversion, multi-loop switch-mode power supplies, LED lighting ballasts, and automotive body modules. The 40 MIPS throughput sustains real-time FOC loops with 20 kHz PWM frequency while leaving headroom for housekeeping tasks. When designing, provide a 4.7-10 uF low-ESR (<5 ohm) capacitor on the VCAP pin for the on-chip 2.5V regulator; VCAP must NEVER be tied to VDD. Allocate one of the PGECx/PGEDx pin pairs for ICSP regardless of final production programming method, to preserve debug access during prototyping. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты
DSPIC33FJ16GP304-I/ML - 16-bit DSC, 40 MIPS, 16KB Flash | Microchip
DSPIC33FJ16GP304-I/ML

DSPIC33FJ16GP304-I/ML - 16-bit DSC, 40 MIPS, 16KB Flash | Microchip

The Microchip DSPIC33FJ16GP304-I/ML is a high-performance 16-bit Digital Signal Controller (DSC) combining the control capability of a microcontroller with the computational throughput of a DSP, delivering 40 MIPS at a 40 MHz clock speed in a 44-pin QFN (8x8 mm) package. It integrates 16 KB of Flash program memory, 2 KB of RAM, a 16-channel 10-bit ADC with 500 ksps conversion rate, and motor-control PWM peripherals, all operating from a 3.0 V to 3.6 V single supply with on-chip voltage regulation. The "I" suffix indicates the industrial temperature grade of -40 C to +85 C, and "ML" denotes the 44-lead QFN surface-mount package. A DSC (Digital Signal Controller) is a hybrid processor architecture that fuses a microcontroller's deterministic control loop with a DSP's MAC (multiply-accumulate) pipeline; this enables single-chip implementation of closed-loop motor control, digital power conversion, and sensor-fusion algorithms that would otherwise require a separate MCU plus DSP partition. The dsPIC33F family targets deterministic real-time embedded control with single-cycle MAC, hardware DSP instructions, and zero-overhead looping. Key features of the DSPIC33FJ16GP304 include 16 KB self-programmable Flash with ECC, 2 KB SRAM, two UART, two SPI, one I2C, two I2S, two CAN, two Capture inputs, one Quad Encoder interface, and six 16-bit PWM outputs with complementary or independent modes. The integrated 16-channel 10-bit ADC with DMA support can sample at up to 500 ksps. The 40 MIPS throughput allows execution of complex motor-control and digital-filter algorithms in real time without off-chip DSP assistance. The internal architecture combines a 16-bit modified Harvard core with a DSP engine, dual 40-bit accumulators, and a 16x16-bit hardware multiplier. The MCU operates at up to 40 MHz from an internal FRC oscillator with PLL, or from an external crystal/clock source. A 16-bit wide instruction path and 24-bit instruction width accommodate both MCU and DSP opcodes. The integrated Power-on Reset, Brown-out Reset, and Watchdog Timer provide robust embedded reliability for industrial deployments. Typical applications include BLDC and PMSM motor control for HVAC blowers and small appliances, digital power conversion (PFC, synchronous rectification), sensorless field-oriented control, LED lighting drivers, and industrial sensor signal conditioning. The combination of CAN, UART, and PWM peripherals also suits automotive body electronics and remote sensor nodes in factory automation. In motor-control designs the QFN-44 footprint fits within a 20 mm stator diameter, enabling compact integrated inverter modules. When designing with the DSPIC33FJ16GP304-I/ML, allocate a decoupling capacitor on VCAP per Microchip application note guidance and follow the recommended PCB layout for the QFN thermal pad. Verify that the ADC acquisition time and PWM duty-cycle resolution meet the application timing budget. Programming is supported by MPLAB X IDE with the free MPLAB XC16 C compiler. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not consolidated in any single source, complementing the manufacturer datasheet with engineer-oriented selection guidance and QFN-layout best practices.

Запрос цены Контакты
DSPIC33FJ16GP304T-I/PT - 16-bit DSC, 40 MIPS, 16KB Flash | Microchip
DSPIC33FJ16GP304T-I/PT

DSPIC33FJ16GP304T-I/PT - 16-bit DSC, 40 MIPS, 16KB Flash | Microchip

The Microchip Technology DSPIC33FJ16GP304T-I/PT is a 16-bit dsPIC33F Digital Signal Controller (DSC) that combines MCU control with DSP processing throughput, delivering up to 40 MIPS at 3.3V from a modified Harvard architecture core. The device integrates 16 KB of Flash program memory and 2 KB of RAM into a 44-pin TQFP (PT) 10x10 mm package, and is specified for the industrial -40C to +85C temperature range. A Digital Signal Controller is a class of microcontroller that merges deterministic interrupt-driven control peripherals with single-cycle MAC DSP engine blocks. Within Microchip's 16-bit portfolio the DSC hierarchy runs: dsPIC33F family -> 16-bit DSC -> MCU + DSP -> embedded processor. The dsPIC33F branch itself targets 3.3V designs at 40 MIPS, contrasting with the 5V dsPIC30F branch, and shares a common instruction set with the PIC24F MCU family so that existing PIC24 tools, libraries and PIMs are reused. This semantic placement explains why the part shows up in motor, power-conversion and audio applications rather than in pure signal-chain analog roles. The DSP engine is the headline feature: a 16x16-bit single-cycle hardware multiplier combined with a 40-bit barrel shifter and 40-bit accumulators gives the DSC native DSP throughput without off-loading work to a companion DSP chip. On-chip peripherals include multiple UART, SPI, IrDA-capable UART, I2C, and LINbus interfaces for embedded connectivity; 35 digital I/O pins populate the 44-pin TQFP; and the part supports boundary-scan (JTAG) and in-circuit serial programming (ICSP) for production test. Typical applications include brushless-DC and permanent-magnet synchronous motor control (sensored and sensorless FOC), digital power conversion (PFC, full-bridge, LLC), Class-D and Class-AB audio amplifiers, switched-mode power supply DSP loops, and sensor-fusion front ends for industrial drives. Each of these workloads benefits from deterministic interrupt latency plus the single-cycle MAC throughput that a plain MCU cannot deliver. When designing with the dsPIC33FJ16GP304, supply it from a regulated 3.0V to 3.6V rail (typical 3.3V) and budget enough Flash endurance budget for field-upgradeable firmware. The 16 KB Flash and 2 KB RAM place this part at the entry level of the dsPIC33F lineup, so larger code bases should step up to the dsPIC33FJ32GP or dsPIC33FJ64GP family for additional headroom. This page synthesizes distributor availability and pricing (as of 2026-09-26), drop-in same-package alternatives drawn from the same dsPIC33FJ16GP304 die, and practical design notes not consolidated in the manufacturer datasheet, offering an engineer-facing supplement to the Microchip datasheet 70290J.

Запрос цены Контакты
DSPIC33FJ16GS402-50I/MM - 16-bit SMPS DSC, 50 MIPS, 28-QFN | Microchip
DSPIC33FJ16GS402-50I/MM

DSPIC33FJ16GS402-50I/MM - 16-bit SMPS DSC, 50 MIPS, 28-QFN | Microchip

The Microchip Technology DSPIC33FJ16GS402-50I/MM is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F "GS" family, engineered specifically for high-performance digital switch-mode power supply (SMPS) and digital power-conversion applications. It delivers 50 MIPS of processing throughput at 50 MHz, integrates 16 KB of Flash program memory (16K x 8), and is housed in a 28-pin QFN-S (6x6 mm) exposed-pad package (MM). The device operates from a 3.0V to 3.6V supply across the industrial -40C to +85C range. A Digital Signal Controller is a hybrid class of microcontroller that combines a deterministic 16-bit MCU core with a high-throughput DSP engine in a single die. In the broader taxonomy, the DSC sits between general-purpose microcontrollers (MCU) and standalone digital signal processors (DSP), giving designers single-cycle MAC operations alongside traditional peripheral control. The dsPIC33F GS family extends this architecture with hardware peripherals targeting power conversion: high-speed PWM, 10-bit ADC, analog comparators, and dedicated SMPS fault handling. The DSPIC33FJ16GS402 features up to four high-speed PWM channels with 1.04 ns resolution at 50 MIPS, a 2 Msps 10-bit ADC, four analog comparators with programmable hysteresis, and a cycle-by-cycle current-limiting interface. It supports multiple switch-mode topologies including boost, buck, flyback, forward, SEPIC, Cuk, half-bridge, full-bridge, and PFC stages. Hardware-level fault inputs allow nanosecond-scale shutdown of the PWM outputs without CPU intervention, which is essential for safety-rated power stages. The internal architecture uses a modified Harvard bus with two data fetches and one instruction fetch per cycle, a 16 x 16-bit working register array, and a DSP engine with dual 40-bit accumulators and a single-cycle MAC. The Flash program memory supports endurance of 1000 erase/write cycles minimum, and the device includes an integrated PLL that accepts external oscillator crystals or the internal Fast RC oscillator. Typical applications include AC-to-DC converters, isolated DC-to-DC converters, power factor correction (PFC) front ends, uninterruptible power supplies (UPS), digital LED drivers, and battery chargers. The wide operating temperature and integrated analog make it suitable for industrial, telecom, and renewable-energy power architectures. When designing with the DSPIC33FJ16GS402, route the exposed thermal pad (EP) directly to a ground copper pour of at least 1 square inch to dissipate heat from the PWM gate-drive transitions and ADC sampling. Decouple VDD/VSS pairs with 100 nF ceramic capacitors placed within 3 mm of every supply pin, and route the analog AVSS/AVDD pair with a separate ferrite bead from the digital supply to preserve ADC accuracy. This page synthesizes distributor pricing, drop-in alternatives drawn from the same Microchip dsPIC33F GS family, and practical PCB-layout guidance for the DSPIC33FJ16GS402-50I/MM that complement the manufacturer datasheet.

Запрос цены Контакты
DSPIC33FJ16GS402-50I/SP - 16-bit 50 MIPS SMPS DSC | Microchip
DSPIC33FJ16GS402-50I/SP

DSPIC33FJ16GS402-50I/SP - 16-bit 50 MIPS SMPS DSC | Microchip

The Microchip Technology DSPIC33FJ16GS402-50I/SP is a 16-bit Digital Signal Controller (DSC) with 50 MIPS performance, 16 KB Flash, and 2 KB SRAM, housed in a 28-pin SPDIP (Skinny Plastic DIP, through-hole) package. It belongs to the dsPIC33F SMPS family, integrating a high-performance dsPIC DSC CPU with high-speed PWM modules, multi-channel 10-bit ADC, and analog comparators tailored for digital switch-mode power supply (SMPS) control loops. What is a Digital Signal Controller? A Digital Signal Controller (DSC) combines the interrupt-driven, deterministic control of a microcontroller (MCU) with the computational throughput of a digital signal processor (DSP). It sits in the taxonomy: DSC -> MCU + DSP -> embedded controller -> semiconductor. In digital power conversion, the DSC's single-cycle MAC and barrel shifter enable tight multi-loop control of voltage and current at switching frequencies of several hundred kHz, which a generic MCU cannot close-loop fast enough to support stable, efficient power conversion. Key features of the DSPIC33FJ16GS402-50I/SP include 4 high-speed PWM channels with duty-cycle resolution suitable for buck, boost, and PFC topologies, a 10-bit ADC with up to 1 Msps conversion rate supporting current and voltage sensing, integrated analog comparators for cycle-by-cycle current limiting, a 16-bit wide data path, and peripheral pin select for flexible routing of digital functions. The part supports 3.0 V to 3.6 V single-supply operation and is offered in the industrial -40C to +85C temperature range (I/SP suffix). The architecture pairs a modified Harvard bus with a 16-bit dsPIC DSC engine and DSP accumulator, allowing designers to implement digital compensators (Type-II/Type-III, PID) directly on-chip while leaving headroom for housekeeping tasks such as PMBus/sequencing. Compared with pure MCUs, this DSC reduces BOM by replacing op-amp-based analog compensation loops with firmware-based digital loops, improving reliability and supply-setpoint flexibility. Typical applications include AC/DC converters, DC/DC converters (buck, boost, LLC), power factor correction (PFC) stages, uninterruptible power supplies (UPS), digital solar micro-inverters, and LED drivers. It is also used in motor control and induction-heating power stages where high-resolution PWM and fast ADC sampling are essential. A key design consideration when using this part is that the 28-pin SPDIP package is through-hole and best suited for prototyping, low-volume production, or designs that demand socketed/replaceable parts. For high-volume SMT designs, Microchip offers the same die in MM (QFN) and SO packages. Ensure the SMPS peripherals' PWM and ADC pin assignments are routed away from switching nodes to minimize noise injection into sensitive analog inputs. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical digital-power design notes not aggregated on the manufacturer product page or distributor listings.

Запрос цены Контакты
DSPIC33FJ16GS402-E/SO - 40 MIPS 16-bit SMPS DSC, 16KB Flash | Microchip
DSPIC33FJ16GS402-E/SO

DSPIC33FJ16GS402-E/SO - 40 MIPS 16-bit SMPS DSC, 16KB Flash | Microchip

The Microchip Technology DSPIC33FJ16GS402-E/SO is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F "GS" family, optimized for digital switch-mode power supply (SMPS) and other high-speed power-conversion applications. The device integrates a high-performance dsPIC33 CPU core delivering up to 40 MIPS at 3.0-3.6 V, paired with 16 KB of Flash program memory and 2 KB of RAM, and is housed in a 28-pin SOIC ("/SO") package rated for the extended (-40C to +125C) automotive temperature grade as indicated by the "-E" suffix. Background Knowledge: A Digital Signal Controller (DSC) is a hybrid architecture that combines a microcontroller (MCU) with a Digital Signal Processor (DSP) on a single core. In the power-conversion domain, DSCs are widely used because SMPS topologies require both deterministic closed-loop control (an MCU strength) and high-throughput math for PID compensation, digital filtering, and PFC algorithms (a DSP strength). The DSPIC33FJ16GS402 belongs to the broader dsPIC33F family, which is a 16-bit Harvard architecture that sits hierarchically as: dsPIC33FJ16GS402 -> dsPIC33F family -> 16-bit DSC -> Microchip DSC portfolio -> embedded controller category. Key features include up to four 10-bit ADC modules with dedicated Sample-and-Hold and 2×2.7 Msps throughput for multi-loop current/voltage sensing, four analog comparators with a 2.5 ns response time for high-speed peak-current-mode control, four dedicated PWM generators with 7.5 ns resolution, and three 16-bit timer/counters. The device integrates advanced SMPS peripherals such as a 4-channel high-speed PWM, configurable fault inputs, and a programmable dead-time generator that supports interleaved, multi-phase, and full-bridge topologies without external logic. Architecture deep-dive: The DSPIC33FJ16GS402 implements a Modified Harvard architecture with separate program and data buses, a 16-bit data path, a single-cycle MAC (40-bit accumulator), and barrel shifter. SMPS-specific peripherals - the PWM, ADC, and comparator modules - are tightly coupled via a high-speed Trigger/Sync matrix so that ADC sampling can be triggered by a PWM edge with sub-microsecond deterministic latency. Built-in self-reset brown-out, watchdog timer, and ICD (In-Circuit Debugger) support allow field-updateable firmware in production power supplies. Typical applications include AC-DC converters, isolated DC-DC modules, Power Factor Correction (PFC) stages, uninterruptible power supplies (UPS), solar inverters, digital lighting ballasts, and high-frequency battery chargers. The wide operating temperature range (extended -40C to +125C) also supports automotive 12 V/24 V power systems and industrial motor-control drives. When designing with this DSC, allocate PCB area for analog/digital ground separation (AGND/DGND pins) and keep high-current switching traces away from the ADC input pins. Place the VCAP decoupling capacitor (pin 20) close to the regulator core to ensure low-jitter operation of the high-speed PWM and comparator blocks. This page synthesizes distributor pricing, drop-in SOIC-28 alternatives, and practical design notes - information not found in the Microchip datasheet alone - for engineers comparing the DSPIC33FJ16GS402-E/SO to next-generation dsPIC33CK/CN parts.

Запрос цены Контакты
DSPIC33FJ16GS402-E/SP - 40 MIPS 16KB Flash SMPS DSC | Microchip
DSPIC33FJ16GS402-E/SP

DSPIC33FJ16GS402-E/SP - 40 MIPS 16KB Flash SMPS DSC | Microchip

The Microchip DSPIC33FJ16GS402-E/SP is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, engineered for high-performance digital power conversion. It delivers up to 40 MIPS of CPU performance, integrates 16 KB of Flash program memory and 2 KB of RAM, and is housed in a 28-pin SPDIP (0.300 inch) through-hole package. The device targets switched-mode power supply (SMPS) and digital power-conversion applications. A Digital Signal Controller is a hybrid architecture that combines the deterministic interrupt latency and peripheral set of a microcontroller with the high-throughput DSP engine required for closed-loop control algorithms. The dsPIC33F family specifically integrates high-speed PWM modules, high-speed ADCs, and analog comparators that are essential for multi-loop digital power topologies. Compared with a general-purpose MCU, a DSC such as the dsPIC33FJ16GS402 can execute a digital compensator plus housekeeping tasks within a single switching cycle at multi-hundred-kHz PWM frequencies. Key features of the DSPIC33FJ16GS402 include up to four 16-bit PWM outputs with a dedicated PWM time base, a 10-bit ADC with conversion rates up to 4 Msps, four on-chip analog comparators with 4 ns typical propagation delay, and communication peripherals including I2C, SPI, and UART. The integrated analog comparator outputs can directly trigger the PWM module for hardware-level cycle-by-cycle current limiting, which simplifies firmware and reduces protection latency in PFC, full-bridge, and synchronous buck designs. The device operates from 3.0 V to 3.6 V. Typical applications include AC-DC and DC-DC converters, power factor correction (PFC) stages, uninterruptible power supplies (UPS), digital welding, induction cooking, and high-density quarter-brick intermediate bus converters. The "-E" suffix denotes the extended industrial temperature range of -40C to +125C, and "/SP" indicates the 28-pin SPDIP package, suited for prototyping and industrial-grade designs that require through-hole mounting. When designing with this device, allocate the high-speed PWM and analog comparator pins early in the PCB layout to avoid routing detours that introduce propagation delay skew. Use the ICSP interface (PGECx/PGEDx pairs) for in-circuit programming and debugging, and verify the PGEC/PGED pin pair selection matches the chosen debugger configuration before PCB fabrication.

Запрос цены Контакты
DSPIC33FJ16GS402-H/SP - 16-bit SMPS DSC, 50 MIPS, 16KB Flash, SPDIP-28 | Microchip
DSPIC33FJ16GS402-H/SP

DSPIC33FJ16GS402-H/SP - 16-bit SMPS DSC, 50 MIPS, 16KB Flash, SPDIP-28 | Microchip

The Microchip Technology DSPIC33FJ16GS402-H/SP is a 16-bit Digital Signal Controller (DSC) optimized for digital switch-mode power supply (SMPS) and high-performance power-conversion applications, delivering 50 MIPS of CPU performance from a 16 KB on-chip Flash program memory and 2 KB SRAM in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. A Digital Signal Controller is a hybrid between a microcontroller (MCU) and a Digital Signal Processor (DSP). It combines deterministic MCU peripherals, interrupts and a C-friendly instruction set with a single-cycle MAC DSP engine, a 40-bit accumulator and a barrel shifter. Within the power-management taxonomy, the dsPIC33F 'GS' family sits between a generic MCU and a dedicated power-conversion DSP, with on-chip high-resolution PWM (1.04 ns PWM edge resolution), dedicated analog comparators and high-speed 10-bit ADCs that simplify multi-loop digital control loops. Key features include a 16 KB Flash program store, 2 KB SRAM, three 16-bit timers plus one 32-bit timer, a 6-channel 10-bit ADC with up to 4 Msps conversion rate, four analog comparators with 10 ns response time, and four matched PWM channels capable of 1.04 ns edge resolution with 750 ps PWM duty-cycle granularity. The 'H' temperature grade extends the operating range from -40 °C to +150 °C, while the '-50' speed designator confirms the 50 MIPS execution rate (40 MIPS for the '-40' speed bin). Dedicated peripherals such as the PWM Fault input, current reset, and a cycle-by-cycle current-limiting mode allow direct interface to power-stage feedback signals. Architecture-wise, the device uses a modified Harvard bus with separate program and data paths, a 16-bit-wide datapath, dual 40-bit accumulators, and a DSP engine capable of single-cycle 16x16-bit MAC operations, which is sufficient to execute Type-II/Type-III voltage-mode and average-current-mode compensators at typical SMPS switching frequencies (50 kHz to 1 MHz). Typical applications include AC-DC converters, isolated and non-isolated DC-DC converters (buck, boost, half-bridge, full-bridge, LLC), Power Factor Correction (PFC) stages, Uninterruptible Power Supplies (UPS), digital lighting ballasts, and solar inverters. The wide -40 °C to +150 °C junction range also supports automotive under-hood and industrial harsh-environment designs. When designing with this device, reserve adequate Flash for the compensation algorithm and state-machine lookup tables (typical SMPS firmware consumes 6-10 KB). Use the high-speed PWM Fault pin to latch-protect the converter on over-current events, and place a 100 nF decoupling capacitor adjacent to every VDD/VSS pair as recommended in the device BSDL file. This page synthesizes distributor pricing, same-brand drop-in alternatives in the SPDIP-28 footprint, and practical design notes that complement, but do not replace, the manufacturer datasheet.

Запрос цены Контакты
DSPIC33FJ16GS402-I/MM - 16-bit SMPS DSC, 40 MIPS, 16KB Flash | Microchip
DSPIC33FJ16GS402-I/MM

DSPIC33FJ16GS402-I/MM - 16-bit SMPS DSC, 40 MIPS, 16KB Flash | Microchip

The Microchip Technology DSPIC33FJ16GS402-I/MM is a 16-bit Digital Signal Controller (DSC) in the dsPIC33F "GS" family, optimized for digital switch-mode power supply (SMPS) and digital power-conversion applications. It integrates a 40 MIPS dsPIC33F DSC core with 16 KB Flash program memory and runs from a 3.0V to 3.6V supply. The part is housed in a 28-pin QFN (MM) plastic package, 6 x 6 mm with 0.90 mm height, and offers 21 I/O ports along with high-speed PWM, on-chip ADC, and analog comparators dedicated to multi-loop SMPS control. A Digital Signal Controller combines a microcontroller with a DSP engine on a single die. The dsPIC33F GS variants add high-resolution PWM, fast ADC, and analog comparators specifically to support AC/DC converters, DC/DC converters, power factor correction (PFC), uninterruptible power supplies (UPS), and digital lighting ballasts. By collapsing the analog control loop into firmware, the designer gains flexibility, programmability, and active tuning over the converter's operating region. The DSPIC33FJ16GS402-I/MM belongs to the power management and digital control IC hierarchy: dsPIC33F -> 16-bit DSC -> microcontroller/DSP hybrid -> embedded controller. Key features include 4 PWM channels with high resolution, 10-bit ADC with multiple S&H, dedicated analog comparators for cycle-by-cycle current limiting, a fixed-point DSP engine with barrel shifter, and boundary-scan support (JTAG). CMOS process technology keeps active current low and provides idle and sleep modes for energy-conscious designs. The 16-bit DSC architecture delivers deterministic control loop timing needed for high-frequency SMPS loops (often 100 kHz to 1 MHz switching). Architecturally, the device pairs a modified Harvard bus to a DSP engine that natively supports MAC operations on 16-bit data, enabling on-the-fly filtering and control law execution inside the PWM interrupt service routine. Boundary scan (IEEE 1149.1) aids board-level testing. The flash program memory supports self-programming, allowing in-field firmware updates for adaptive power-supply tuning. Typical applications include AC/DC and DC/DC converters, Power Factor Correction (PFC) front ends, UPS systems, solar micro-inverters, digital lighting ballasts, and motor control for small BLDC/PMSM drives. Industrial and consumer SMPS designs benefit from its digital-loop flexibility. When designing with this device, allocate the ICSP pins (PGECx/PGEDx) to a header for in-circuit debug and programming. Use one pair as a matched set; mixing PGEC2 with PGED1 will not function. Add bulk and decoupling capacitance near VDD/VSS pairs and route the analog AVSS separately from digital grounds. This page synthesizes distributor pricing, drop-in alternatives within the same 28-pin QFN footprint, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты