AD4030-24FMCZ - 24-Bit 2 MSPS SAR ADC Evaluation Board | Analog Devices
Артикул: AD4030-24FMCZ ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $285 | $285,00 |
| 5 | $268 | $1.340,00 |
| 10 | $252 | $2.520,00 |
| 25 | $238 | $5.950,00 |
| 50 | $225 | $11.250,00 |
AD4030-24FMCZ Обзор
An evaluation board is a dedicated PCB that engineers use to characterize a complex component without first committing to a custom design. The AD4030-24FMCZ pairs the AD4030-24 single-channel 24-bit SAR ADC with a configurable analog front end (AFE), enabling engineers to evaluate noise, linearity, and throughput against datasheet limits. ADCs of this precision category are typically used as precision data acquisition front-ends and as benchmark modules when prototyping measurement systems.
Key features highlighted by the manufacturer include a guaranteed maximum ±0.9 ppm integral nonlinearity (INL), no missing codes at 24 bits across the -40 °C to +125 °C operating range, a 2 MSPS sample rate (the related AD4032-24 is the 500 kSPS variant), and the Easy Drive input architecture that simplifies the drive amplifier chain. The on-chip reference buffer with integrated decoupling capacitor reduces external BOM count, and the no-pipeline-delay track-and-hold makes the part suitable for multiplexed control loops.
The board uses Analog Devices' Flexi-SPI interface, supporting standard SPI, echo-clock, and ADC-host-clock modes plus optional DDR clocking. This allows 10 MHz serial clock operation while sustaining 2 MSPS conversion throughput, easing FPGA timing closure and enabling galvanic isolation with standard digital isolators. Power-on-reset (POR) on both 5 V and 1.8 V rails resets internal registers at power-up and on rail collapse.
Typical applications include precision industrial weighing scales, seismic and geophysical instrumentation, medical patient-monitoring front-ends, multi-channel data-acquisition modules, and audio-bandwidth high-resolution measurement systems. The wide common-mode input range of the Easy Drive inputs lets the board digitize signals directly from bridges, thermocouples, and current-sense shunts. The no-latency track-and-hold also suits closed-loop control systems where deterministic acquisition timing is essential.
The most common design trade-off for engineers using this eval board is FMC connector routing - long impedance-discontinued traces will degrade the 2 MSPS / 24-bit noise floor. Use the shortest possible cable to the host, and where possible capture full-resolution samples into the FPGA fabric before any rate compression. For noisy bench environments, power the board through a linear supply rather than the FMC 5 V rail.
Аналоги без доработки для AD4030-24FMCZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
EVAL-AD4630-24FMCZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
EVAL-AD4630-16FMCZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD4030-24FMCZ Максимальные параметры и электрические характеристики
| Product Type | Evaluation Board |
| Target Device | AD4030-24 (24-bit, 2 MSPS SAR ADC) |
| Разрешение | 24 bits |
| Sample Rate (Max) | 2 MSPS |
| ADC Architecture | SAR (successive-approximation register) |
| Каналы | 1 (single-channel ADC) |
| Integral Nonlinearity (Max) | ±0.9 ppm |
| Missing Codes | None guaranteed at 24 bits |
| Диапазон рабочих температур | -40 °C to +125 °C (target device) |
| Host Interface | FMC (FPGA Mezzanine Card) LPC connector |
| Compatible Carrier | Digilent ZedBoard and FMC-compliant carriers |
| Digital Interface | Flexi-SPI (SPI / echo-clock / host-clock / DDR) |
| Input Front End | Easy Drive configurable AFE |
| Reference | Internal reference buffer with integrated decoupling capacitor |
| POR Circuit | Yes (5 V and 1.8 V rails) |
| Datasheet Pages | 50 (per alldatasheet.com index) |
Руководство по цоколевке AD4030-24FMCZ в корпусе standard
Цоколевка для AD4030-24FMCZ (корпус standard). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для AD4030-24FMCZ.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
AD4030-24FMCZ подходит для 6 применениеs: Precision Weighing Scales, Seismic and Geophysical Instrumentation, Medical Patient-Monitoring Front Ends, Multichannel Data Acquisition Modules, Audio-Bandwidth High-Resolution Measurement, Industrial Closed-Loop Control Systems.
Precision Weighing Scales
The AD4030-24's ±0.9 ppm maximum INL and no-missing-codes 24-bit performance make the EVAL-AD4030-24FMCZ an ideal board for evaluating front-end signal chains for industrial weighing scales. The Easy Drive analog front end accepts the high-impedance output of a load-cell bridge directly, while the 2 MSPS throughput lets designers oversample and digitally average at 24 bits of resolution. The 5 V / 1.8 V POR guarantees deterministic boot of the load-cell calibration sequence after power-up. Placed between the load cell output and a ZedBoard controller, the board demonstrates a complete weigh-scale prototype with proper grounding and shielding — ensuring accuracy well below the 6000e commercial scale specification.
Рекомендуется
Seismic and Geophysical Instrumentation
The AD4030-24's 24-bit dynamic range and 2 MSPS sample rate suit broadband seismic and geophysical instrumentation where wide-bandwidth high-resolution digitisation of piezo and geophone signals is required. According to the AD4030-24/AD4032-24 datasheet, the SAR converter's zero pipeline delay is critical when synchronising to GPS timing pulses in field acquisition units. The Flexi-SPI interface with echo-clock and DDR options keeps serial clock rates low, simplifying the use of digital isolators in the field station wiring. The EVAL-AD4030-24FMCZ lets engineers qualify the ADC noise floor against geophone signal levels before field deployment.
Рекомендуется
Medical Patient-Monitoring Front Ends
For ECG, EEG, and pulse-oximetry front ends, the EVAL-AD4030-24FMCZ lets prototyping teams measure how the 24-bit AD4030-24 handles wide dynamic range biological signals. The integrated reference buffer with on-chip decoupling cuts the surrounding bill of materials compared to discrete reference paths. The Easy Drive architecture relaxes the drive-amplifier settle-time requirements, allowing simpler low-power op-amps than competing 24-bit ADCs demand. Combined with a ZedBoard, this board forms a benchtop patient-monitoring prototype suitable for early design verification under IEC 60601 development workflows.
Рекомендуется
Multichannel Data Acquisition Modules
The EVAL-AD4030-24FMCZ is a baseline board for building multichannel data-acquisition modules where several AD4030-24 ADCs can be synchronised through their CONVST inputs and back-end FPGA logic. The 2 MSPS throughput combined with 24-bit precision allows a 4-board stack of FMC cards to reach 8 MSPS aggregate sample rate at 24 bits. The optional DDR Flexi-SPI clocking eases multi-board synchronisation timing closure on Virtex/UltraScale-class FPGAs. The board's analog front end also demonstrates how to buffer and level-shift a -10 V to +10 V industrial input range into the ADC common-mode input.
Рекомендуется
Audio-Bandwidth High-Resolution Measurement
When measuring audio-bandwidth signals at 24 bits, the AD4030-24 on the EVAL-AD4030-24FMCZ board supports both high-resolution audio engineering and acoustic test instrumentation. The 2 MSPS rate digitises up to ~920 kHz of baseband while preserving 24-bit noise linearity, far exceeding the 192 kHz needs of typical pro-audio systems. The Flexi-SPI echo-clock mode allows low-jitter data transfer into an FPGA for FFT analysis of audio DAC performance, speaker distortion, or microphone calibration. The board enables direct comparison of AC-vs-DC distortion performance against an Audio Precision analyser without committing to a custom PCB.
Рекомендуется
Industrial Closed-Loop Control Systems
The EVAL-AD4030-24FMCZ supports prototyping of industrial servo/control loops where the AD4030-24's zero pipeline delay is the decisive advantage over pipelined ADCs. The on-chip track-and-hold exhibits no latency, making the converter ideal for deterministic feedback control of valves, drives, and precision stages. The Easy Drive front end tolerates wide-input-common-mode swings common in motor-control environments, while the 5 V and 1.8 V POR resets internal logic at power-on for safe startup. Used with a ZedBoard, the board forms a development platform for evaluating control-loop bandwidth and stability under real PWM noise injection.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD4030-24FMCZ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | EVAL-AD4630-24FMCZ | EVAL-AD4630-16FMCZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package / Form Factor | FMC board (single-channel ADC eval) | FMC board - same | FMC board - same |
| Target ADC | AD4030-24 (24-bit, single-channel) | AD4630-24 (24-bit, dual-channel) | AD4630-16 (16-bit, dual-channel) |
| Resolution | 24 bits | 24 bits | 16 bits |
| Maximum Sample Rate | 2 MSPS | 2 MSPS per channel | 2 MSPS per channel |
| INL (Max) | ±0.9 ppm (ADC, not board-measured) | ±1.0 ppm (ADC, similar class) | Less critical at 16-bit |
| Channels | 1 | 2 | 2 |
| Digital Interface | Flexi-SPI (SPI / echo-clock / DDR) | Flexi-SPI - same | Flexi-SPI - same |
| Compatible Carrier | ZedBoard / FMC-LPC carriers | ZedBoard / FMC-LPC - same | ZedBoard / FMC-LPC - same |
Ключевые отличия
- Lowest-noise single-channel SAR ADC in Analog Devices' 24-bit precision portfolio (против EVAL-AD4630-24FMCZ)
- Zero pipeline delay (против Pipelined 24-bit ADCs)
- Easy Drive analog front end (против Discrete op-amp front ends)
Заметки по проектированию
Route the FMC connector to the host FPGA with differential 100 Ω impedance-controlled traces. The 2 MSPS Flexi-SPI DDR mode places a 250 ps setup/hold window on data edges, so uncontrolled routing will corrupt the 24-bit noise floor that justifies this ADC. Short the FMC connector directly into the FPGA bank without series components to avoid skim-jitter.
Power the EVAL-AD4030-24FMCZ from a clean linear 5 V regulator rather than the FMC 12 V or 5 V rail when benchtop-characterising AC performance. The AD4030-24's ±0.9 ppm INL guarantee is achieved only when switching-noise coupling through the test bench is below -120 dBc. Use a series ferrite and 10 uF ceramic decap on the 5 V input of the eval board.
Do not assume the Easy Drive analog front end is fully buffered - the device still requires the input amplifier settle to within ±0.5 LSB at 24 bits (≈30 nV at 2 MSPS) before the next conversion begins. Verify with the eval board first by stepping load-cell or DC source cables and observing the INL histogram before committing to a custom layout.
Информация о соответствии
RoHS and REACH compliance per Analog Devices product-page statements. Evaluation boards themselves are not AEC-Q100 qualified; the AEC-Q100 status of the AD4030-24 itself should be confirmed separately for automotive projects.
