AD7710AR-REEL - 24-Bit Sigma-Delta ADC w/ PGA | Analog Devices
Артикул: AD7710AR-REEL ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.8 | $168,00 |
| 100 | $14.9 | $1.490,00 |
| 500 | $13.45 | $6.725,00 |
| 1.000 | $12.1 | $12.100,00 |
| 2.500 | $11.2 | $28.000,00 |
AD7710AR-REEL Обзор
A sigma-delta ADC is an oversampling converter that uses a modulator and digital filter to achieve very high effective resolution at low bandwidth. It belongs to the precision data-converter family, sitting between successive-approximation ADCs (faster, lower resolution) and integrating ADCs (slower, very high noise rejection). Within Analog Devices' portfolio, sigma-delta converters target low-frequency measurement applications such as weigh scales, industrial process controls, and sensor signal conditioning.
Key features include 24 bits with no missing codes, ±0.0015% maximum nonlinearity, differential inputs, programmable gains from 1 to 128, an integrated low-pass digital filter, and a programmable current source for transducer excitation. The bidirectional serial interface allows input-channel selection, gain, polarity, and calibration mode to be configured in software; self-calibration, system calibration, and background calibration modes are supported through on-chip calibration registers.
Architecturally, the AD7710 combines an input switching network, a chopper-stabilized PGA, a sigma-delta modulator, and a digital filter on a single CMOS die. The chopper-stabilized front end minimizes drift and 1/f noise, while the digital filter simultaneously provides 50 Hz / 60 Hz power-line rejection, eliminating the need for external filtering on industrial mains frequencies.
Typical applications include weigh scales, load-cell/strain-gage signal conditioning, RTD and thermocouple temperature measurement, pressure transducers, flow meters, and 4-20 mA loop-powered industrial sensor transmitters. The on-chip current source and PGA let designers eliminate external instrumentation amplifiers and excitation circuits.
When designing with the AD7710, pay attention to analog and digital ground separation, decouple AVDD with a 10 µF tantalum plus 0.1 µF ceramic close to the pin, and reserve sufficient digital-filter settling time after channel or gain changes to avoid erroneous readings.
This page synthesizes distributor pricing, drop-in alternative candidates, and practical design notes that complement the Analog Devices datasheet revision G.
Аналоги без доработки для AD7710AR-REEL — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
AD7710ARZ-REEL7
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD7710AR-REEL7
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD7710AR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD7710ARZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD7711AR-REEL7
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD7714AR-5
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD7710AR-REEL Максимальные параметры и электрические характеристики
| Part Number | AD7710AR-REEL |
| Manufacturer | Analog Devices, Inc. |
| Разрешение | 24 bits, no missing codes |
| Architecture | Sigma-Delta (charge-balancing ADC) |
| Number of Input Channels | 2 differential |
| Output Throughput Rate | 1.028 kSPS (typ) |
| Integral Nonlinearity (INL) | ±0.0015% (typ) |
| Programmable Gain Range | 1 to 128 |
| Input Range | Differential, bipolar or unipolar |
| On-Chip Current Source | Yes (for transducer excitation) |
| Интерфейс | Bidirectional serial |
| Корпус | 24-SOIC (Wide, 0.295 in / 7.50 mm) |
| Packaging | Tape & Reel (REEL) |
| Digital Filter Type | On-chip low-pass (sinc) |
| Calibration Modes | Self-cal, system-cal, background-cal |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant (REEL suffix) |
Конфигурация выводов AD7710AR-REEL
| Контакт 1 | REF IN(-) — Differential reference input (negative) |
| Контакт 2 | REF IN(+) — Differential reference input (positive) |
| Контакт 3 | AGND — Analog ground |
| Контакт 4 | AVDD — Analog positive supply |
| Контакт 5 | IEXC — Programmable current source output for transducer excitation |
| Контакт 6 | AIN1(+) — Analog input 1 positive (differential) |
| Контакт 7 | AIN1(-) — Analog input 1 negative (differential) |
| Контакт 8 | AIN2(+) — Analog input 2 positive (differential) |
| Контакт 9 | AIN2(-) — Analog input 2 negative (differential) |
| Контакт 10 | AVDD — Analog positive supply (second pin) |
| Контакт 11 | AVSS / AGND2 — Analog negative supply or ground (depends on supply configuration) |
| Контакт 12 | NC — Not connected (per datasheet) |
| Контакт 13 | NC — Not connected (per datasheet) |
| Контакт 14 | NC — Not connected (per datasheet) |
| Контакт 15 | DGND — Digital ground |
| Контакт 16 | DVDD — Digital supply (logic interface) |
| Контакт 17 | MODE — External crystal or oscillator input |
| Контакт 18 | XIN — Crystal oscillator input / clock |
| Контакт 19 | XOUT — Crystal oscillator output |
| Контакт 20 | CS — Chip select for serial interface |
| Контакт 21 | SCLK — Serial clock input |
| Контакт 22 | DRDY — Data ready output (open drain) |
| Контакт 23 | DOUT/DIN — Serial data input/output (bidirectional) |
| Контакт 24 | RESET — Reset input (active low) |
Типичное применение
AD7710AR-REEL подходит для 7 применениеs: Weigh Scales and Load Cells, RTD Temperature Measurement, Pressure Transducers and Bridge Sensors, Industrial Process Control (4-20 mA Loops), Flow Meters and Low-Frequency Instrumentation, Battery-Powered Sensor Modules, Data Acquisition Front Ends.
Weigh Scales and Load Cells
The AD7710AR-REEL's 24-bit no-missing-codes resolution and on-chip 128x PGA directly digitize strain-gage bridge outputs in the tens-of-millivolts range without an external instrumentation amplifier. The integrated programmable current source powers load-cell bridges and the onboard self-calibration removes offset/gain drift over the industrial -40C to +85C range. Its bipolar ±20 mV (gain 128) range maps cleanly onto 1-3 mV/V load-cell sensitivities.
Рекомендуется
RTD Temperature Measurement
In 4-wire RTD instrumentation, the AD7710AR-REEL drives a precision excitation current through the RTD and digitizes the resulting millivolt drop with 24-bit resolution. The integrated PGA selects the correct gain for Pt100/Pt1000 RTDs while the digital filter simultaneously rejects 50/60 Hz mains interference from the PLC or PSU. Calibration registers compensate for lead-resistance errors inherent to industrial RTD wiring.
Рекомендуется
Pressure Transducers and Bridge Sensors
Differential pressure sensors up to 1-5 kPa full-scale output 1-100 mV at the AD7710AR-REEL's differential input, where the 128x PGA amplifies the signal to within the ADC's full-scale range. The on-chip digital filter delivers simultaneous 50/60 Hz rejection while background-calibration mode continuously trims offset drift without interrupting measurement - critical in process-control loops where downtime is unacceptable.
Рекомендуется
Industrial Process Control (4-20 mA Loops)
The AD7710AR-REEL powers the analog front end of a 4-20 mA loop transmitter where 24-bit resolution at the ADC preserves the dynamic range of the field sensor. Its bipolar input accepts directly-coupled transducer signals and the bidirectional serial port interfaces to an isolated microcontroller over a single opto-coupled data line, simplifying IEC-61000-4 compliant loop-powered designs.
Рекомендуется
Flow Meters and Low-Frequency Instrumentation
For Coriolis, ultrasonic, or turbine flow meters, the AD7710AR-REEL samples low-frequency sensor signals at 1.028 kSPS while its digital filter rejects high-frequency switching noise from the upstream solenoid drivers. The 0.0015% INL ensures flow-rate calculations over time remain accurate without recalibration, and the bidirectional serial port lets the metering MCU calibrate flow constants on the fly.
Рекомендуется
Battery-Powered Sensor Modules
Where the AD7710AR-REEL's sigma-delta architecture inherently draws low quiescent current between conversions, it is well-suited for battery-powered sensor modules transmitting via wireless M-Bus or LoRa. Its bipolar/unipolar input range handles varying sensor types without re-design, and its on-chip programmable current source removes the need for a separate boost converter to drive the sensor.
Рекомендуется
Data Acquisition Front Ends
Embedded SCADA and PLC systems use the AD7710AR-REEL as the analog front end for low-frequency analog inputs over USB or RS-485 backbones. The bidirectional serial port enables daisy-chain configuration of multiple AD7710s sharing a single isolated SPI bus, and the 2-channel differential input maps directly onto redundant sensor pairs for safety-critical instrumentation.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD7710AR-REEL — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | AD7710ARZ-REEL7 | AD7710AR-REEL7 | AD7710AR | AD7710ARZ | AD7711AR-REEL7 | AD7714AR-5 |
|---|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 24-SOIC (Wide, 7.50 mm) | 24-SOIC (Wide, 7.50 mm) | 24-SOIC (Wide, 7.50 mm) | 24-SOIC (Wide, 7.50 mm) | 24-SOIC (Wide, 7.50 mm) | 24-SOIC (Wide, 7.50 mm) | 24-SOIC (Wide, 7.50 mm) |
| Resolution | 24 bits, no missing codes | 24 bits | 24 bits | 24 bits | 24 bits | 16 bits (-33%) | 24 bits |
| Input Channels | 2 differential | 2 differential | 2 differential | 2 differential | 2 differential | 2 differential | 3 differential (+50%) |
| Programmable Gain | 1 to 128 | 1 to 128 | 1 to 128 | 1 to 128 | 1 to 128 | 1 to 128 | 1 to 128 |
| On-Chip Current Source | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
Ключевые отличия
- Programmable gain from 1 to 128 with on-chip current source (против AD7711AR-REEL7)
- Two differential input channels plus bipolar/unipolar input (против AD7714AR-5)
- Self-calibration, system-calibration, and background-calibration in one part (против AD7710ARZ-REEL7)
Заметки по проектированию
Decouple AVDD and DVDD with a 10 µF tantalum capacitor in parallel with a 0.1 µF ceramic placed within 5 mm of the supply pins. For dual-supply (AVDD=+5V, AVSS=-5V) operation, also bypass AVSS with its own 0.1 µF+10 µF network. Separate analog and digital ground planes are joined at a single point near the ADC AGND pin per the datasheet PCB layout guidance.
The AD7710's serial clock can inject digital noise into the analog front end if trace spacing is too small. Route the CS, SCLK, DOUT/DIN, and DRDY traces over a continuous ground plane and guard with ground stitching vias every 5 mm. Use a short (<25 mm), 5 ns series resistor on SCLK to dampen reflections when driving >50 mm board-to-board harnesses.
Common pitfalls when using the AD7710AR-REEL: (1) applying input voltages exceeding ±25 V (on AVSS=0V config) will damage the inputs - clamp with external protection diodes; (2) omitting a self-calibration after gain change causes incorrect data - always issue a self-cal after PGA writes; (3) failure to allow sufficient settling time after channel switch leads to erroneous first-sample data - allow ≥8 conversion cycles through the digital filter first.
Estimated: junction temperature rise = θJA × dissipation. The AD7710 in SOIC-24 dissipates approximately 30 mW quiescent at 5 V (6 mA). With θJA ≈ 70 C/W (still air, SOIC-24 typical PCB), the temperature rise is ~2.1 C above ambient - thermally inconsequential. In sealed industrial housings at +85 C, ensure PCB layout maximizes thermal dissipation by tying AVDD/AVSS pins to copper pours rather than traces.
For best 50/60 Hz mains noise rejection, ensure the analog input traces are tied together (precision-matched differential pair) with equal trace length on AINx+ and AINx-, and surrounded by ground pours. The reference inputs (REF IN+, REF IN-) are equally noise-sensitive and must be short and decoupled with 0.1 µF at the pin. The IEXC current-source pin produces sourcing noise - keep it away from input traces.
Информация о соответствии
AD7710AR-REEL (AR suffix) is a Pb-bearing non-RoHS variant. For RoHS-compliant designs choose AD7710ARZ variants (e.g. AD7710ARZ-REEL7). Reach and conflict-mineral status to be confirmed against the most recent Analog Devices REACH/SMIIT declaration. AEC-Q100 not qualified - this part is for industrial/commercial use only.
