AD843JN - 34MHz CBFET Fast-Settling Op Amp | Analog Devices
Артикул: AD843JN ✓ АктивенAD843JN Обзор
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The AD843 belongs to the high-speed voltage-feedback operational-amplifier family, combining low-noise FET input characteristics with wide closed-loop bandwidth. This makes it useful within the broader power-management and analog-signal-processing hierarchy wherever accurate, rapid response to small voltage signals is required.
The AD843’s principal advantages include its 34 MHz bandwidth, 0.6 nA input bias current, and 135 ns settling performance. The CBFET input stage helps maintain very low input bias current, which is valuable when the source impedance is high and bias-current-induced errors must remain small. Its fast settling behavior is especially useful in pulse, measurement, buffering, and feedback-control systems that cannot tolerate long analog settling periods.
The AD843 is part of the Analog Devices family of wide-bandwidth operational amplifiers and is intended for applications requiring both FET-like input behavior and rapid closed-loop response. The manufacturer describes the amplifier as suitable for instrumentation applications, low-impedance drive stages, video and image-processing circuits, and feedback loops where the 10 V settling specification is relevant. Its bandwidth also allows operation at lower closed-loop gains, subject to the stability and compensation guidance in the manufacturer datasheet.
Typical uses include buffer amplifiers, instrumentation front ends, sample-and-hold interfaces, video signal conditioning, pulse shaping, and active filtering. In these systems, the AD843 can preserve small input signals, minimize source-loading error through its low bias current, and settle quickly after a large input transition. The 8-pin PDIP package is particularly appropriate for prototypes, educational platforms, legacy industrial equipment, and through-hole assemblies that require a socketed or manually assembled implementation.
When laying out a circuit, keep the feedback path short and connect compensation, decoupling, and signal-ground components according to the manufacturer’s recommended topology. The power rails must satisfy the device’s operating limits, and unused input pins must be handled so they cannot collect noise or unintended signals. Because high-speed feedback circuits can oscillate, evaluate stability across the intended gain, load, and supply conditions rather than relying only on nominal bandwidth figures.
This product page combines the manufacturer’s AD843 performance description with package information, application-oriented guidance, replacement analysis, and practical design guidance. It is intended to help engineers identify whether the 34 MHz bandwidth, 0.6 nA input bias current, 135 ns settling time, and 8-pin PDIP package meet their circuit and assembly requirements.
Аналоги без доработки для AD843JN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
AD843KNZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD843AQ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD843BQ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD843AR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
AD844JN
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD843JN Максимальные параметры и электрические характеристики
| Number of Circuits | 1 circuit |
| Amplifier Type | Operational amplifier |
| Input Transistor Type | CBFET |
| Small-Signal Bandwidth | 34 MHz |
| Input Bias Current | 0.6 nA |
| Settling Time | 135 ns to within 0.01% for a 10 V step |
| Корпус | 8-pin PDIP |
| Число выводов | 8 pins |
| Тип монтажа | Through hole |
| Product Category | Instrumentation, operational amplifiers, buffer amplifiers |
Конфигурация выводов AD843JN
| Контакт 1 | NC — Not connected |
| Контакт 2 | −IN — Inverting input |
| Контакт 3 | +IN — Non-inverting input |
| Контакт 4 | V− — Negative supply voltage |
| Контакт 5 | NC — Not connected |
| Контакт 6 | OUT — Amplifier output |
| Контакт 7 | V+ — Positive supply voltage |
| Контакт 8 | NC — Not connected |
Типичное применение
AD843JN подходит для 6 применениеs: High-Speed Instrumentation Front Ends, Pulse Shaping and Fast Feedback Loops, Video and Wideband Signal Conditioning, Active Filtering and Frequency-Shaping Networks, Sample-and-Hold Buffer Interfaces, Data Acquisition and Analog Control Loops.
High-Speed Instrumentation Front Ends
The AD843JN fits instrumentation front ends that must acquire or monitor relatively high-frequency signals without loading the source excessively. Its 0.6 nA input bias current reduces errors when the transducer or source impedance is high, while 34 MHz bandwidth preserves signal amplitude and phase within the application band. The device can be used as a buffer or as the active element in a feedback circuit. Its 135 ns settling time after a 10 V step is valuable when the acquisition path must recover rapidly from an input transient. Because this is a high-speed amplifier, keep the feedback loop compact, control source and load capacitance, and verify stability using the compensation guidance in the manufacturer datasheet.
Рекомендуется
Pulse Shaping and Fast Feedback Loops
The AD843JN is appropriate for pulse-shaping, edge-processing, and fast feedback circuits because it combines 34 MHz bandwidth with 135 ns settling to within 0.01% after a 10 V step. These characteristics allow the amplifier to recover from large transitions more quickly than a general-purpose precision operational amplifier. A practical implementation places the AD843 in a closed-loop gain configuration and keeps the feedback components close to the device. Designers should check output swing against the actual pulse amplitude, provide local supply bypassing, and test ringing or oscillation with the complete source impedance and load. The 0.6 nA input bias current is also useful when the pulse source presents substantial impedance.
Рекомендуется
Video and Wideband Signal Conditioning
The AD843JN can condition wideband video or communications signals whose useful spectrum extends beyond the bandwidth of ordinary precision op amps. Its 34 MHz gain-bandwidth characteristic provides response for baseband video, monitor, or control signals, and the low 0.6 nA input bias current helps when driving a high-impedance source or termination network. The amplifier should operate with closed-loop gain selected so that the required bandwidth and phase margin are retained. Layout must minimize loop area and prevent long feedback traces from adding delay. Before deployment, verify slew rate, output-voltage swing, supply range, and channel-to-channel timing against the signal standard, because bandwidth alone does not guarantee faithful reproduction of every video waveform.
Рекомендуется
Active Filtering and Frequency-Shaping Networks
The AD843JN is suitable for active filter and frequency-shaping networks where the required signal bandwidth makes a low-bandwidth precision amplifier unsuitable. Its 34 MHz gain-bandwidth product permits useful closed-loop bandwidth at moderate gains, and the CBFET input’s 0.6 nA bias current limits loading in high-impedance filter sections. Place feedback resistors and capacitors close to the amplifier, maintain short ground returns, and account for the amplifier’s finite gain and open-loop response in the final filter calculation. Input and output loading can shift the nominal cutoff, while parasitic capacitance can reduce phase margin. Validate the completed filter at the intended signal level because slew rate and output swing can also influence large-signal behavior.
Рекомендуется
Sample-and-Hold Buffer Interfaces
The AD843JN can buffer the interface between a fast sampling or switching stage and a downstream measurement circuit. Its 34 MHz bandwidth reduces the time required for signals to propagate through the amplifier, while its 135 ns settling specification supports recovery after a 10 V transition. Low input bias current of 0.6 nA is beneficial when the preceding circuit has a high output impedance. In implementation, keep the device’s input and feedback components close together, provide a low-impedance return path, and confirm that the output can charge the sampling and hold capacitance within the acquisition interval. The amplifier’s output drive and slew rate must be checked against that capacitance rather than inferred from bandwidth alone.
Рекомендуется
Data Acquisition and Analog Control Loops
The AD843JN is useful in data-acquisition and analog control paths that require quick settling after a measurement or control event. Its 34 MHz bandwidth permits operation at higher signal rates than a conventional precision amplifier, and the 0.6 nA input bias current helps preserve accuracy when driving from high-impedance sensors. The 135 ns settling time can reduce recovery delay following a 10 V step. Designers should nevertheless compare offset voltage, input noise, common-mode range, and output swing because those specifications determine whether the device also satisfies the precision requirements of the application. A grounded, decoupled supply and short feedback route are essential to preserving the advertised fast behavior.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD843JN — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | AD843KNZ | AD843AQ | AD843BQ | AD843AR | AD844JN |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Mounting Type | Through hole | Through hole | Through hole | Through hole | Through hole | Through hole |
| Order-Code Qualification | JN suffix | KNZ suffix | AQ suffix | BQ suffix | AR suffix | JN suffix |
| Price Tier | Request a quote | Request a quote | Request a quote | Request a quote | Request a quote | Request a quote |
Ключевые отличия
- Combines wide bandwidth with exceptionally low input bias current (против AD844JN)
- Fast recovery after a large signal transition (против AD843AR)
- Through-hole package supports socketed and legacy-style assembly (против AD843JNZ)
Заметки по проектированию
Keep the AD843JN feedback loop physically small and connect each feedback component directly to the relevant device pins. High-speed loops can pick up parasitic inductance and capacitance that reduce phase margin even when the nominal gain is lower than expected. Route the output away from input and supply nodes, use a low-impedance ground plane, and place compensation and decoupling capacitors according to the manufacturer’s recommended application circuits. For socketed prototypes, include provision for testing oscillation without disturbing the final ground topology.
Do not assume that 34 MHz closed-loop bandwidth is available at every gain setting. Gain-bandwidth behavior, slew rate, output-current capability, load capacitance, and the selected compensation determine the usable response. Also confirm the input common-mode range and output swing against the actual supply rails. The quoted 135 ns settling time applies to the manufacturer’s specified 10 V step and test conditions; it should not be treated as settling time for every gain, load, or supply configuration.
Use local supply bypassing and verify both rail voltages and ground return paths before evaluating performance. Fast output transitions can demand more current than the circuit’s steady-state load suggests, while supply ripple can enter the output through power-supply rejection paths. Check the datasheet limits for the exact AD843JN grade, observe the maximum total supply voltage, and ensure that the source can support the required transient current. Decoupling capacitor placement should be evaluated together with the feedback layout rather than optimized independently.
Treat the AD843JN as a wideband analog component: long breadboard jumpers, sockets, and probe leads may add enough delay or capacitance to alter a high-gain feedback loop. Prefer a short PCB implementation for final verification, and compare scope measurements taken with different probing methods to avoid mistaking probe artifacts for amplifier ringing. If driving a capacitive load, confirm that the load magnitude and phase do not compromise stability, or add an isolation resistor where the circuit topology permits it.
Информация о соответствии
The available product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because the AD843 is a general-purpose operational amplifier rather than an automotive-qualified device.