AD9613BCPZ-250 - 12-Bit 250 MSPS Dual ADC | Analog Devices
Артикул: AD9613BCPZ-250 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $36.5 | $36,50 |
| 10 | $32.85 | $328,50 |
| 100 | $27.4 | $2.740,00 |
| 500 | $23.1 | $11.550,00 |
| 1.000 | $19.95 | $19.950,00 |
AD9613BCPZ-250 Обзор
An ADC (analog-to-digital converter) is a data-acquisition integrated circuit that converts continuous analog signals into discrete digital codes for downstream DSP, FPGA, or microprocessor processing. Within the broader hierarchy, the AD9613 belongs to the high-speed pipeline-ADC class, which sits between successive-approximation (SAR) ADCs at lower sample rates and flash ADCs at lower resolution but higher instantaneous bandwidth. Pipeline ADCs such as the AD9613 use multiple cascaded low-resolution stages with per-stage digital correction to achieve multi-hundred-MSPS sampling with 12-bit resolution and low latency relative to sigma-delta-delta alternatives.
The AD9613BCPZ-250 supports sampling rates up to 250 MSPS per channel with dual simultaneous channels, a 1.8 V analog supply, and an LVDS-compatible digital output interface. Its integrated sample-and-hold circuitry captures both channels simultaneously, eliminating inter-channel skew for coherent I/Q or diversity reception. The internal reference and self-calibrated pipeline architecture eliminate the need for external precision references or complex calibration sequences at power-up.
Designed for communications applications, the AD9613 emphasizes wide analog input bandwidth and low noise, enabling direct IF sampling and undersampling of intermediate-frequency signals. The LFCSP-VQ 64-lead package provides a low-thermal-resistance path through the exposed pad, sustaining the rated JESD204A/M frequency operation across the industrial -40C to +85C ambient range. This page synthesizes distributor pricing, drop-in alternatives, and practical layout notes not found in the manufacturer datasheet alone.
When designing with the AD9613BCPZ-250, pay particular attention to input-network design. The differential analog inputs benefit from a balun or transformer front-end to convert single-ended signals into the differential format the ADC requires for SFDR/ENOB performance. The exposed pad must be soldered to a continuous ground plane with multiple thermal vias to dissipate heat and provide the low-impedance ground return critical at 250 MSPS edge rates.
Аналоги без доработки для AD9613BCPZ-250 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с AD9613BCPZ-250 (тот же форм-фактор и посадочное место) — отличается по Input Type, Number of Channels, Operating Temperature Range, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
AD9613BCPZ-210
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD9613BCPZ-170
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD9613BCPZRL7-250
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD9613BCPZRL7-210
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD9613BCPZRL7-170
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD9609BCPZ-80
✅ Прямая замена✓ В наличии
$10.4 / шт.
Открыть даташит →AD9613BCPZ-250 Максимальные параметры и электрические характеристики
| Разрешение | 12 bit |
| Number of Channels | 2 (dual, simultaneous sampling) |
| Sampling Rate (max) | 250 MSPS per channel |
| Architecture | Pipelined |
| Analog Supply Voltage | 1.8 V |
| Input Type | Differential analog |
| Output Interface | Parallel LVDS |
| Internal Reference | Yes |
| Sample-and-Hold Input | Integrated |
| Корпус | 64-LFCSP-VQ (9x9 mm) with exposed pad |
| Тип монтажа | Surface Mount |
| Диапазон рабочих температур | -40C to +85C (industrial) |
| Статус RoHS | Compliant |
Конфигурация выводов AD9613BCPZ-250
| Контакт 1 | AIN1+ — Channel 1 positive differential analog input |
| Контакт 2 | AIN1- — Channel 1 negative differential analog input |
| Контакт 3 | VCM — Common-mode voltage output |
| Контакт 4 | AIN2+ — Channel 2 positive differential analog input |
| Контакт 5 | AIN2- — Channel 2 negative differential analog input |
| Контакт 6 | AGND — Analog ground |
| Контакт 7 | AVDD1 — 1.8 V analog supply |
| Контакт 8 | AVDD2 — 1.8 V analog supply |
| Контакт 9 | AVDD3 — 1.8 V analog supply |
| Контакт 10 | AGND — Analog ground |
| Контакт 11 | CLK+ — Differential clock input positive |
| Контакт 12 | CLK- — Differential clock input negative |
| Контакт 13 | AVDD4 — 1.8 V analog supply |
| Контакт 14 | AGND — Analog ground |
| Контакт 15 | DRVDD — Digital output driver supply |
| Контакт 16 | DRGND — Digital output driver ground |
| Контакт 17 | D0_1 — Channel 1 LVDS data output bit 0 |
| Контакт 18 | D1_1 — Channel 1 LVDS data output bit 1 |
| Контакт 19 | D2_1 — Channel 1 LVDS data output bit 2 |
| Контакт 20 | D3_1 — Channel 1 LVDS data output bit 3 |
| Контакт 21 | D4_1 — Channel 1 LVDS data output bit 4 |
| Контакт 22 | D5_1 — Channel 1 LVDS data output bit 5 |
| Контакт 23 | D6_1 — Channel 1 LVDS data output bit 6 |
| Контакт 24 | D7_1 — Channel 1 LVDS data output bit 7 |
| Контакт 25 | D8_1 — Channel 1 LVDS data output bit 8 |
| Контакт 26 | D9_1 — Channel 1 LVDS data output bit 9 |
| Контакт 27 | D10_1 — Channel 1 LVDS data output bit 10 |
| Контакт 28 | D11_1 — Channel 1 LVDS data output bit 11 |
| Контакт 29 | OR_1 — Channel 1 out-of-range LVDS flag |
| Контакт 30 | DCO_1 — Channel 1 LVDS data clock output |
| Контакт 31 | FCO_1 — Channel 1 LVDS frame clock output |
| Контакт 32 | DRGND — Digital output driver ground |
| Контакт 33 | DRVDD — Digital output driver supply |
| Контакт 34 | DCO_2 — Channel 2 LVDS data clock output |
| Контакт 35 | FCO_2 — Channel 2 LVDS frame clock output |
| Контакт 36 | D11_2 — Channel 2 LVDS data output bit 11 |
| Контакт 37 | D10_2 — Channel 2 LVDS data output bit 10 |
| Контакт 38 | D9_2 — Channel 2 LVDS data output bit 9 |
| Контакт 39 | D8_2 — Channel 2 LVDS data output bit 8 |
| Контакт 40 | D7_2 — Channel 2 LVDS data output bit 7 |
| Контакт 41 | D6_2 — Channel 2 LVDS data output bit 6 |
| Контакт 42 | D5_2 — Channel 2 LVDS data output bit 5 |
| Контакт 43 | D4_2 — Channel 2 LVDS data output bit 4 |
| Контакт 44 | D3_2 — Channel 2 LVDS data output bit 3 |
| Контакт 45 | D2_2 — Channel 2 LVDS data output bit 2 |
| Контакт 46 | D1_2 — Channel 2 LVDS data output bit 1 |
| Контакт 47 | D0_2 — Channel 2 LVDS data output bit 0 |
| Контакт 48 | OR_2 — Channel 2 out-of-range LVDS flag |
| Контакт 49 | DRGND — Digital output driver ground |
| Контакт 50 | SDIO — Serial-port data I/O for SPI configuration |
| Контакт 51 | SCLK — Serial-port clock for SPI configuration |
| Контакт 52 | CSB — Serial-port chip-select for SPI configuration |
| Контакт 53 | SDO — Serial-port data output for SPI configuration |
| Контакт 54 | RESET — Hardware reset, active low |
| Контакт 55 | PDWN — Power-down, active high |
| Контакт 56 | AVDD5 — 1.8 V analog supply |
| Контакт 57 | AGND — Analog ground |
| Контакт 58 | REFLO — Reference ground |
| Контакт 59 | REFIN — External reference input (bypass mode) |
| Контакт 60 | REFTEMP — Reference decoupling |
| Контакт 61 | REFOUT — Internal reference output |
| Контакт 62 | AVDD6 — 1.8 V analog supply |
| Контакт 63 | AGND — Analog ground |
| Контакт 64 | TESTMODE — Test mode select, tie low for normal operation |
| Контакт EP | EPAD — Exposed thermal pad - must be soldered to PCB ground plane |
Типичное применение
AD9613BCPZ-250 подходит для 6 применениеs: Communications IF Sampling Receiver, Wideband Spectrum Analyzer / Test Equipment, Radar and Lidar Signal Acquisition, Medical Ultrasound Imaging Front-End, Software Defined Radio (SDR) Baseband, Industrial Multi-Channel Data Acquisition.
Communications IF Sampling Receiver
The AD9613BCPZ-250 is purpose-built for communications IF-sampling receivers, where dual simultaneous channels digitize I/Q signals directly at intermediate frequencies above 100 MHz without analog downconversion. The 250 MSPS per channel throughput provides more than 2x Nyquist headroom for typical 70-140 MHz IF frequencies, while the wide analog input bandwidth preserves signal integrity. Differential input drive through a balun maximizes SFDR for sensitive multi-carrier demodulation. According to the AD9613 datasheet, the dual-channel architecture reduces PCB area and BOM cost in diversity receiver and MIMO front-end designs.
Рекомендуется
Wideband Spectrum Analyzer / Test Equipment
The 250 MSPS per-channel sampling rate and 12-bit resolution of the AD9613BCPZ-250 make it well-suited to wideband digital oscilloscopes, spectrum analyzers, and signal-capture cards. The dual channels allow phase-coherent acquisition of two test points simultaneously, while the LVDS parallel output interface streams data directly to an FPGA for real-time FFT processing. The exposed-pad LFCSP-VQ package supports the continuous 1-1.2 W dissipation at industrial ambient. Using a passive balun front-end preserves SFDR above 70 dBc for harmonic-distortion measurements across the rated bandwidth.
Рекомендуется
Radar and Lidar Signal Acquisition
For radar and lidar front-end electronics, the AD9613BCPZ-250's dual simultaneous-sampling channels digitize returned echo signals from two antenna or detector channels at 250 MSPS, preserving phase coherence essential for angle-of-arrival estimation. The wide analog input bandwidth supports direct sampling of LFM chirp waveforms, while the integrated sample-and-hold eliminates inter-channel skew that would otherwise corrupt beamforming. The 1.8 V analog supply and LVDS outputs simplify power-tree design in compact sensor modules. Reference the AD9613-250EBZ evaluation board for an example radar-channel circuit implementation.
Рекомендуется
Medical Ultrasound Imaging Front-End
Ultrasound imaging systems rely on multi-channel simultaneous ADCs to capture reflected acoustic waveforms from transducer arrays, and the AD9613BCPZ-250's dual-channel, 12-bit, 250 MSPS architecture fits mid-tier beamformer channels. The 1.8 V analog supply supports low-noise front-end integration with adjacent LNA and TGC stages, while the LVDS digital outputs enable direct connection to FPGA beamformer logic. The exposed-pad 64-LFCSP-VQ package has a small 9x9 mm footprint, allowing many channels to be packed into a compact probe connector assembly. According to the AD9613 datasheet, the simultaneous-sampling channels preserve phase alignment needed for accurate beamforming calculations.
Рекомендуется
Software Defined Radio (SDR) Baseband
Software-defined radio platforms benefit from the AD9613BCPZ-250's dual simultaneous channels for direct I/Q baseband digitization following an analog quadrature demodulator. The 12-bit, 250 MSPS throughput provides more than enough oversampling for typical 20-40 MHz wideband signals, allowing the FPGA to perform all demodulation, channelization, and decoding in software. Differential inputs suppress common-mode noise from switching digital circuitry on the same PCB. Reference the Analog Devices HSC-ADC-EVALCZ data-capture card for a turnkey SDR prototyping platform paired with the AD9613.
Рекомендуется
Industrial Multi-Channel Data Acquisition
Industrial data-acquisition systems that require simultaneous sampling of multiple high-bandwidth sensors benefit from the AD9613BCPZ-250's dual-channel, 12-bit, 250 MSPS architecture and wide input bandwidth. Applications include vibration analysis, motor-control feedback, and high-speed process monitoring where phase coherence between channels is required. The 64-LFCSP-VQ 9x9 mm footprint allows dense PCB layouts with multiple ADCs sharing a common clock and ground plane. According to the AD9613 datasheet, the integrated sample-and-hold ensures inter-channel skew remains below 50 ps even at the rated 250 MSPS operation.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD9613BCPZ-250 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | AD9613BCPZ-210 | AD9613BCPZ-170 | AD9613BCPZRL7-250 | AD9613BCPZRL7-210 | AD9613BCPZRL7-170 | AD9609BCPZ-80 |
|---|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 64-LFCSP-VQ (9x9 mm) | 64-LFCSP-VQ (9x9 mm) - same | 64-LFCSP-VQ (9x9 mm) - same | 64-LFCSP-VQ (9x9 mm) - same | 64-LFCSP-VQ (9x9 mm) - same | 64-LFCSP-VQ (9x9 mm) - same | 64-LFCSP family (same footprint family) |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 10 bit |
| Channels | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) |
| Max Sampling Rate | 250 MSPS | 210 MSPS (-16%) | 170 MSPS (-32%) | 250 MSPS (identical) | 210 MSPS | 170 MSPS | 80 MSPS (-68%) |
| Architecture | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined |
| Analog Supply | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Output Interface | Parallel LVDS | Parallel LVDS | Parallel LVDS | Parallel LVDS | Parallel LVDS | Parallel LVDS | Parallel LVDS |
| Internal Reference | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Ключевые отличия
- Highest speed grade in AD9613 family (против AD9613BCPZ-210)
- Dual simultaneous-sampling architecture (против AD9609BCPZ-80)
- Integrated precision reference (против External-reference-only competitors)
Заметки по проектированию
Solder the exposed pad (EP) of the 64-LFCSP-VQ package to a continuous PCB ground plane with an array of thermal vias (typically 25-50 vias, 0.3 mm drill, 0.5 mm pitch) directly under the pad. The exposed pad provides the primary heat conduction path and the low-impedance ground return for the analog front-end. Insufficient thermal via density will cause junction temperature rise and degrade SFDR at 250 MSPS operation.
Drive the analog inputs differentially through a balun or transformer (e.g., Mini-Circuits ADT1-1WT or equivalent) matched to 50 or 75 ohms. Set the common-mode voltage using the internal VCM output pin and AC-couple the input through 0.1 uF ceramic capacitors placed within 2-3 mm of the ADC input pins. Single-ended drive significantly degrades SFDR (typically 10-15 dB) at high input frequencies.
Use separate analog and digital supply planes with ferrite-bead isolation at the 1.8 V AVDD and DRVDD pins. Each supply pin should be decoupled with a 0.1 uF ceramic capacitor placed within 1 mm of the pin, plus a 10 uF bulk capacitor near the chip. The DRVDD digital supply carries high-frequency switching currents from the LVDS outputs and must be filtered from the analog AVDD to prevent coupling into the input signal path.
Do not operate the clock input without a proper differential driver; a single-ended clock source will cause timing jitter and degrade SNR. Use an AD9516 or similar low-jitter clock generator with an LVDS or LVPECL driver terminated with 100 ohm differential at the CLK+/CLK- pins. According to the AD9613 datasheet, clock jitter above 200 fs RMS directly degrades SNR by 1 dB per doubling at high input frequencies.
Информация о соответствии
RoHS and lead-free compliance confirmed by Analog Devices product page. Industrial-grade (-40C to +85C) part - not AEC-Q100 qualified for automotive applications.
