Analog Devices

AD9833BRM - 25 MHz 10-Bit DDS Waveform Generator | Analog Devices

Артикул: AD9833BRM ✓ Активен
2.3 V to 5.5 V Vdss 10-pin MSOP Package 25 MHz Speed
MOQ: 1 |

AD9833BRM Обзор

The Analog Devices AD9833BRM is a low-power direct digital synthesis waveform generator with a 25 MHz maximum output frequency, 28-bit frequency tuning, and a 10-bit DAC, packaged in a 10-pin MSOP. It generates sine, triangular, and square-wave outputs from a serial data interface while operating from a 2.3 V to 5.5 V supply.

A direct digital synthesizer, or DDS, is a programmable waveform generator that represents the output of a sine function as a sequence of phase values. These phase values pass through a digital-to-analog converter to create the requested waveform. DDS technology belongs to the broader clock and timing IC category and provides digitally controlled frequency selection without requiring a conventional analog voltage-controlled oscillator.

The AD9833BRM combines a 28-bit frequency control word with a 10-bit DAC resolution. A single serial write supplies the frequency setting, while separate control inputs select sine, triangle, or square-wave operation and control data flow. Its low-power 12.65 mW operating figure and 2.3 V to 5.5 V supply range suit compact instrumentation and portable test equipment.

The AD9833 uses a phase accumulator and phase-to-amplitude conversion architecture to create its output waveform. The 28-bit tuning word provides fine frequency-addressing granularity, while the 10-bit DAC defines the amplitude resolution of the generated waveform. Serial programming reduces the number of control lines required compared with parallel DDS architectures, which is advantageous where PCB area is constrained.

Typical applications include time-domain reflectometry, frequency-response testing, sensor excitation, actuator testing, tone generation, and communications test equipment. The AD9833 is especially useful when a low-cost, programmable source is needed for repetitive laboratory or industrial measurements rather than a high-stability reference signal.

When laying out a circuit, place the device and its decoupling capacitors close together, route the serial interface away from sensitive analog nodes, and treat the DAC output as an analog signal that may require filtering. Confirm the output amplitude and waveform purity at the frequencies and loads required by the end application.

This product overview combines the AD9833BRM operating characteristics with package, purchasing, replacement, and design guidance to support faster component selection and implementation planning.

Аналоги без доработки для AD9833BRM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Для этого товара нет аналогов без доработки.

Запросить аналоги

AD9833BRM Характеристики

Product Type Direct digital synthesis waveform generator
Maximum Output Frequency 25 MHz
Frequency Tuning Resolution 28 bit
DAC Resolution 10 bit
Number of DACs 1 DAC
Supply Voltage Range 2.3 V to 5.5 V
Power Consumption 12.65 mW
Supported Waveforms Sine, triangular, and square wave
Control Interface Serial
Корпус 10-pin MSOP
Тип монтажа Surface mount
Тип выхода Analog waveform output

Руководство по цоколевке AD9833BRM в корпусе 10-pin msop

Цоколевка для AD9833BRM (корпус 10-pin msop). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 10-pin msop для AD9833BRM

Нет подробных данных о распиновке для AD9833BRM.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

AD9833BRM подходит для 6 применениеs: Time-Domain Reflectometry, Sensor Excitation, Frequency-Response Testing, Actuator and Motor Testing, Communications Test Equipment, Portable and Compact Test Instruments.

🌐

Time-Domain Reflectometry

The AD9833BRM fits time-domain reflectometry because it generates programmable sine, triangular, or square-wave excitation signals up to 25 MHz for launching pulses into a cable, PCB trace, or network structure. Its 28-bit frequency tuning word gives a test system fine control over stimulus frequency, while the 10-bit DAC supplies the analog waveform required by a sampling receiver. A practical implementation should pair the output with suitable impedance matching, filtering, and trigger synchronization. The primary benefit is a compact source that can be retuned through the serial interface instead of requiring multiple physical oscillators.

🏭

Sensor Excitation

The AD9833BRM can provide adjustable sinusoidal excitation for resistive, capacitive, and frequency-dependent sensors in industrial monitoring systems. An output frequency of up to 25 MHz and 28-bit tuning resolution allow the excitation to be swept while the 10-bit DAC defines the available amplitude levels. Because the waveform is programmed serially, a microcontroller or test controller can change excitation conditions without mechanical tuning. Designers should limit the output into the sensor’s safe operating range, account for DAC output compliance, and filter unwanted harmonics before amplification.

🖥️

Frequency-Response Testing

The AD9833BRM is suitable for compact frequency-response test setups that need a digitally swept source across a wide operating range. The 28-bit frequency control allows fine sweep steps, and the 25 MHz maximum output frequency covers RF-oriented test fixtures and communications hardware. Serial control also supports automated calibration and repeatable stimulus sequences. For accurate results, the analog output path should include low-pass or band-pass filtering appropriate to the measurement bandwidth, while the test system should characterize amplitude accuracy and phase delay at the frequencies of interest.

⚡

Actuator and Motor Testing

The AD9833BRM can generate controlled excitation waveforms for actuator characterization, vibration fixtures, and small motor test systems. Its selectable square-wave output supports discrete switching stimuli, while sine and triangle modes suit linear and resonant response measurements. Serial frequency control makes it practical to run stepped or swept profiles from embedded test electronics. The design must limit current and voltage at the actuator interface, include appropriate buffering, and account for the DAC output’s finite amplitude resolution when precise drive levels are required.

📡

Communications Test Equipment

The AD9833BRM can serve as a programmable test source in communications equipment, signal analyzers, and loopback fixtures. Its 25 MHz maximum frequency and multiple waveform modes provide flexible stimulus for checking receiver and transmitter chains without a large bench generator. The serial interface simplifies integration into automated test software, and the compact 10-pin MSOP package preserves board area. Engineers should add output attenuation, gain control, or filtering where the measured equipment requires calibrated levels, and should verify clock, synchronization, and harmonic performance during fixture development.

🔧

Portable and Compact Test Instruments

The AD9833BRM suits handheld and portable test instruments because it combines waveform generation in a 10-pin MSOP with a 2.3 V to 5.5 V operating range and stated power consumption of 12.65 mW. These characteristics support a compact, low-power source in field-service equipment, education platforms, and automated diagnostic products. The serial control architecture minimizes interface wiring, while selectable waveforms support several measurement modes in one instrument. A practical handheld design should still reserve PCB area for filtering, output conditioning, level control, and robust power decoupling.

Сводка рекомендуемых товаров

AD9833 Base-family waveform generator Используется в: Time-Domain Reflectometry, Sensor Excitation, Frequency-Response Testing, Actuator and Motor Testing, Communications Test Equipment, Portable and Compact Test Instruments AD9833BRM Analog Devices Используется в: Time-Domain Reflectometry, Sensor Excitation, Frequency-Response Testing, Actuator and Motor Testing, Communications Test Equipment, Portable and Compact Test Instruments
What is the AD9833BRM?
The AD9833BRM is a low-power, programmable direct digital synthesis waveform generator capable of producing sine, triangular, and square-wave outputs. It uses a 28-bit frequency tuning word, a 10-bit DAC, and a serial programming interface. According to the Analog Devices AD9833 datasheet, the device is intended for sensing, actuation, and time-domain reflectometry applications where a digitally controlled test waveform is required.
What is the maximum output frequency of AD9833BRM?
The AD9833BRM supports frequencies up to 25 MHz. Its 28-bit frequency tuning word permits fine digital frequency control, while the 10-bit DAC determines the output amplitude resolution. According to the Analog Devices AD9833 datasheet, engineers should verify the required output amplitude and waveform purity at each frequency because the usable signal quality can vary with frequency and operating conditions.
What voltage does AD9833BRM need?
The AD9833BRM operates from a 2.3 V to 5.5 V supply. This range allows it to be used in low-voltage 3.3 V and 5 V systems, subject to the output and input limits of the connected circuitry. The Analog Devices AD9833 datasheet identifies 12.65 mW as the stated power consumption, making the device suitable for compact instrumentation and portable test systems.
What waveforms can AD9833BRM generate?
The AD9833BRM can generate sine, triangular, and square-wave outputs. These three operating modes make it useful for swept-frequency measurements, pulse and square-wave testing, audio-band signal generation, sensor excitation, and time-domain reflectometry. According to the Analog Devices AD9833 datasheet, waveform selection is made through the device control interface rather than by changing external discrete components.
Where can I download the AD9833BRM datasheet PDF?
The official AD9833BRM datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/AD9833.pdf. The document contains the recommended operating conditions, electrical characteristics, pin information, functional description, and application guidance for the AD9833 family. Use the manufacturer document as the controlling reference when checking pin functions, timing, and electrical limits.
Where can I find the AD9833BRM pinout?
The AD9833BRM pinout is published in the pin-configuration section of the official Analog Devices AD9833 datasheet. The part is supplied in a 10-pin MSOP package, so the package drawing and pin-description table should be consulted together when assigning PCB nets. Use that table to verify interface, supply, ground, analog-output, and compensation connections before laying out the board.
What is the AD9833BRM resolution?
The AD9833BRM provides a 28-bit frequency tuning word and a 10-bit DAC resolution. The frequency-control resolution determines how finely the synthesized frequency can be selected, whereas the 10-bit DAC defines the number of amplitude steps available at the analog output. According to the Analog Devices AD9833 datasheet, the combination supports precise programmable excitation in sensing and test applications.
AD9833BRM vs AD9833BRMZ - which should I select?
The AD9833BRM and AD9833BRMZ share the same AD9833 electrical function and 10-pin MSOP footprint, but they differ in orderable packaging presentation. AD9833BRM is identified with tube packaging, while AD9833BRMZ is the tape-and-reel ordering option. Both are direct constructions of the same device rather than distinct drop-in competitors, so choose according to the assembly method required by the production process.
What is the best drop-in replacement for AD9833BRM?
No independent cross-manufacturer drop-in replacement can be established from the available documentation without risking pin, interface, or frequency-performance incompatibility. The AD9833BRMZ is electrically and pin compatible with AD9833BRM, but it is a reel-packaged ordering variant rather than a distinct substitute. Request current availability and lead time for the exact orderable part through the Request a Quote form on this page.
Can AD9833BRMZ replace AD9833BRM?
The AD9833BRMZ can replace AD9833BRM electrically and at the 10-pin MSOP footprint, but the primary difference is packaging. AD9833BRM is associated with tube delivery, whereas AD9833BRMZ is associated with tape-and-reel delivery. Confirm the pick-and-place orientation, exposed thermal or lead geometry, and orderable suffix before treating the two order codes as interchangeable in the bill of materials.
When should I choose AD9833BRM instead of a conventional signal generator?
Choose AD9833BRM when the application needs a compact, digitally programmable waveform source at frequencies up to 25 MHz rather than the stability, modulation, and calibration features of a bench signal generator. Its serial control is useful in automated test systems, and its sine, triangular, and square-wave outputs support sensor excitation, actuator testing, and time-domain reflectometry. The Analog Devices AD9833 datasheet defines its intended low-power waveform-generation role.
Is AD9833BRM suitable for time-domain reflectometry?
Yes, the AD9833BRM is specifically suitable for time-domain reflectometry because it can generate programmable waveforms up to 25 MHz for launching signals into a device or transmission line. Its 28-bit tuning word supports precise frequency selection, and the 10-bit DAC provides the analog source waveform. System performance still depends on output filtering, impedance matching, trigger timing, and receiver design.
How is the AD9833BRM programmed?
The AD9833BRM is programmed through its serial interface, allowing a controller to write frequency and control data to the device. This interface reduces the number of PCB traces compared with a parallel programming architecture and supports compact automated test equipment. The Analog Devices AD9833 datasheet provides the required clock timing, write sequence, and control-word formats needed to implement the serial driver correctly.
Where can I buy AD9833BRM online?
Use the Request a Quote form on this page to request AD9833BRM availability, current lead time, and order quantities. The form supports exact-part sourcing without relying on a static price that may change with inventory or quantity. For design-in support, include the required tube packaging, production quantity, and target schedule when submitting the request.
How much does AD9833BRM cost?
Use the Request a Quote form on this page for the current AD9833BRM price and volume breaks. Pricing for this programmable waveform generator can depend on order quantity, packaging, production schedule, and market availability, so a static quote can become stale. The request should identify the exact AD9833BRM orderable part and the anticipated annual or batch quantity.
Is AD9833BRM in stock and what is its lead time?
Request the current AD9833BRM stock position and lead time through the Request a Quote form on this page. Availability can vary with tube packaging and order quantity, particularly when a production allocation is required. Include the requested delivery date, forecast quantity, and number of annual build schedules so the supplier can respond with an actionable schedule.

Справочные инженерные данные для AD9833BRM — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the AD9833BRM when a compact instrument needs a digitally programmable sine, triangular, or square-wave source with frequencies up to 25 MHz, 28-bit frequency tuning, and a 10-bit DAC. Its serial interface reduces control wiring, and its 2.3 V to 5.5 V supply range supports low-voltage embedded test equipment. The BRM order code is associated with tube packaging, making it appropriate for automated through-hole or tube-fed assembly processes. AD9833BRMZ provides the same electrical construction and 10-pin MSOP footprint in a tape-and-reel ordering presentation, which is generally more convenient for high-volume pick-and-place assembly. Neither is a separate cross-manufacturer performance alternative. For designs requiring greater frequency range, higher DAC resolution, greater output current, or advanced modulation, select a different waveform-generator family rather than treating an order-code variant as a functional upgrade.

Сравнение с аналогами

Параметр Этот товар
Package 10-pin MSOP
Brand Analog Devices
Product Type Direct digital synthesis waveform generator
Maximum Output Frequency 25 MHz
Frequency Tuning Resolution 28 bit
DAC Resolution 10 bit
Number of DACs 1 DAC
Supply Voltage Range 2.3 V to 5.5 V
Power Consumption 12.65 mW
Supported Waveforms Sine, triangular, and square wave
Control Interface Serial
Mounting Type Surface mount

Ключевые отличия

  • Compact programmable waveform generation (против AD9833BRMZ)
  • Multiple output waveforms from one device (против AD9833BRMZ)
  • Low-voltage integration (против AD9833BRMZ)

Заметки по проектированию

Place the AD9833BRM close to its supply decoupling network and route the analog output away from the serial clock and data traces. The 10-pin MSOP footprint leaves little room for long analog routes, so establish a short ground-return path and place filtering components near the VOUT connection. Separate supply-current paths from sensitive measurement nodes to reduce the chance that programming activity and output transitions inject error into the stimulus signal.

Treat VOUT as an analog node even though the source is digitally controlled. The 10-bit DAC resolution can create quantization steps that are relevant in high-gain signal chains, while harmonic content depends on frequency, output loading, and filtering. Begin with a reconstruction or anti-imaging filter appropriate to the highest fundamental used, and validate amplitude accuracy, phase response, and spurious levels at each required test frequency.

Use a supply that remains within the 2.3 V to 5.5 V operating range across temperature and load. Place the required decoupling capacitance directly between the supply and ground pins, with its shortest possible loop. Because serial write activity can produce transient current in compact instruments, verify supply droop and output stability while the AD9833BRM changes frequency or waveform settings; a quiet regulator alone does not guarantee a clean analog output.

Do not assume that a 25 MHz frequency command automatically produces an equally clean 25 MHz sine wave at the load. Output amplitude, filtering, impedance, grounding, and measurement bandwidth all influence usable performance. Check the official Analog Devices AD9833 datasheet for pin functions and recommended application conditions, then prototype the complete output path rather than evaluating only the unloaded digital control interface.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The available product information does not state the requested compliance status. The AD9833 datasheet mentions an automotive model, but the commercial AD9833BRM qualification status must be confirmed against the relevant ordering information.

Данные проверены: 2026-11-15 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

AD9833BRM datasheet AD9833BRM pinout AD9833BRM datasheet pdf AD9833BRM 25 MHz waveform generator AD9833BRM 28 bit tuning AD9833BRM 10 bit DAC AD9833BRM 10 MSOP AD9833BRM TDR application AD9833BRM vs AD9833BRMZ AD9833BRM equivalent AD9833BRM replacement AD9833BRM price Analog Devices AD9833BRM AD9833BRM schematic

Связанные компоненты & термины

Analog Devices AD9833 AD9833BRM AD9833BRMZ direct digital synthesis DDS programmable waveform generator frequency synthesizer clock and timing IC phase accumulator digital-to-analog converter 10-bit DAC 28-bit frequency tuning word sine wave triangular wave square wave serial interface time-domain reflectometry TDR sensor excitation frequency-response testing 2.3 V to 5.5 V supply 10-pin MSOP surface-mount package
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ