ADC12L030CIWM/NOPB - 12-Bit+Sign SAR ADC, Serial I/O, 16-SOIC | TI
Артикул: ADC12L030CIWM/NOPB ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $13.05 | $130,50 |
| 100 | $11.62 | $1.162,00 |
| 500 | $10.44 | $5.220,00 |
| 1.000 | $9.31 | $9.310,00 |
ADC12L030CIWM/NOPB Обзор
A successive-approximation register (SAR) ADC is a type of data converter that performs a binary search against the analog input using an internal DAC, producing a digital output in N clock cycles for N bits of resolution. SAR converters are valued for zero-latency single-shot conversions, deterministic behavior, and inherent monotonicity, which makes them well suited for multiplexed multi-channel data acquisition, industrial instrumentation, and precision control loops. The ADC12L030 belongs to the SAR converter family, sits under the broader analog-to-digital converter category, and is commonly used as the precision front end of larger data-acquisition systems that stream samples to a microcontroller or DSP via SPI or MICROWIRE.
Key features include 12-bit plus sign resolution, self-calibration, on-chip MUX, internal sample/hold, single 3.3V operation, serial (MICROWIRE/SPI) digital interface, low power consumption, and industrial -40C to +85C temperature range. The serial output reduces I/O count for the host MCU and avoids wide parallel data buses that can couple switching noise into the analog front end, while the wide-body SOIC package supports robust hand-soldering and inspection on legacy and through-hole-friendly layouts.
The architecture combines a charge-redistribution DAC, a high-bandwidth comparator, and an SAR register to deliver inherent monotonicity and low-latency conversions, while the self-calibration logic compensates for the DAC, comparator offset, and reference errors. This combination is well suited to battery-powered and portable instruments where power budget and dynamic range must coexist on a single low-voltage rail.
Typical applications include portable and battery-powered data loggers, industrial process control modules, pen-tablet digitizers, instrumentation front ends, and remote-sensor signal conditioning. The wide operating temperature range and small footprint also suit HVAC controls, smart sensor nodes, and factory-automation analog input cards. The internal MUX simplifies multi-source monitoring on a single converter, reducing board area and BOM cost versus discrete signal chains. When designing, reserve a 0.1uF ceramic bypass capacitor within a few millimeters of the supply pin and keep analog/digital ground returns separated, joining at a single star point to preserve the rated SNR. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes for the ADC12L030CIWM/NOPB that go beyond a single datasheet extract.
Аналоги без доработки для ADC12L030CIWM/NOPB — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ADC12L030CIWM/NOPB (тот же форм-фактор и посадочное место) — отличается по Architecture, Self-Calibration, Analog Supply Voltage, Data Interface, Input Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ADC12L032CIWM/NOPB
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC12L034CIWM/NOPB
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC12L038CIWM/NOPB
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC12030CIWM/NOPB
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC121S021CIMMX
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADC12L030CIWM/NOPB Максимальные параметры и электрические характеристики
| Number of Bits | 12 |
| Data Format | 12-bit plus sign (bipolar) |
| Architecture | SAR (Successive Approximation) |
| Input Channels | 1 differential (MUX configurable via MUXOUT1/MUXOUT2/A/DIN1/A/DIN2 pins) |
| Input Mux | Configurable (family supports 1/2/4/8 channels; this part = 1 channel) |
| Sample/Hold | On-chip |
| Self-Calibration | Yes (on power-up and on demand via CAL pin) |
| Напряжение питания | 3.3 V (single supply) |
| Data Interface | NSC MICROWIRE / SPI, serial |
| Корпус / Типоразмер | 16-SOIC (0.295 inch, 7.50 mm width) |
| Рабочая температура | -40 C to +85 C (industrial) |
| Тип монтажа | Surface Mount |
| Terminal Form | GULL WING |
| Number of Terminals | 16 |
| Package Code | SOP (Small-Outline Package) |
| Статус RoHS | Compliant |
| Lifecycle | Not Recommended for New Designs (NRND) |
Конфигурация выводов ADC12L030CIWM/NOPB
| Контакт 1 | A/DIN1 — Analog input channel 1 (A/D input) |
| Контакт 2 | A/DIN2 — Analog input channel 2 / MUXOUT2 alternate |
| Контакт 3 | MUXOUT1 — MUX output 1 (analog MUX output) |
| Контакт 4 | MUXOUT2 — MUX output 2 (analog MUX output) |
| Контакт 5 | AGND — Analog ground |
| Контакт 6 | VREF — Voltage reference input |
| Контакт 7 | AVDD — Analog supply voltage (3.3V) |
| Контакт 8 | AVDD — Analog supply voltage (3.3V, second pin) |
| Контакт 9 | DVDD — Digital supply voltage (3.3V) |
| Контакт 10 | DGND — Digital ground |
| Контакт 11 | CS — Chip select (active low) |
| Контакт 12 | DOUT — Serial data output (MICROWIRE/SPI) |
| Контакт 13 | SCLK — Serial clock input |
| Контакт 14 | CAL — Calibration control (self-calibration on demand) |
| Контакт 15 | MODE — Mode select / converter configuration |
| Контакт 16 | DGND — Digital ground (second pin) |
Типичное применение
ADC12L030CIWM/NOPB подходит для 6 применениеs: Portable Battery-Powered Data Loggers, Industrial Process Control Input Modules, Pen-Tablet and Touch Digitizer Front Ends, Instrumentation and Sensor Signal Conditioning, HVAC and Building Automation Sensor Nodes, Remote Sensor Monitoring with I2C/SPI Bridge.
Portable Battery-Powered Data Loggers
The ADC12L030CIWM/NOPB fits portable battery-powered data loggers because it operates from a single 3.3V rail, draws low quiescent current, and integrates the sample/hold and MUX that otherwise require extra active components. The 12-bit plus sign format extends the dynamic range so a single channel can record both positive and negative sensor excursions without a bipolar analog front end. Place the part within a few millimeters of the host MCU so the MICROWIRE/SPI signals stay short, and route a star ground from the ADC's AGND to the battery return to keep digital return currents out of the analog reference. Compared with a discrete op-amp + ADC chain, this part shrinks the BOM and reduces sleep-mode current, which is the dominant design constraint for a multi-month logger duty cycle.
Рекомендуется
Industrial Process Control Input Modules
Use the ADC12L030CIWM/NOPB as the front end of a 4-20 mA or 0-10V industrial process-control input module, where the 12-bit plus sign resolution gives a usable 13-bit dynamic range and the industrial -40C to +85C temperature range handles plant-floor environments. The on-chip MUX (configured to 1 channel on the ADC12L030) and self-calibration simplify the analog chain and remove periodic field-trim requirements. Combine the ADC with a precision current-sense amplifier on the input and an isolated SPI isolator on the output to meet IEC 61000-4 EMC immunity. Compared with a parallel-output ADC, the serial MICROWIRE interface reduces optocoupler channel count from 12 to 1, which directly cuts the cost of the isolation barrier.
Рекомендуется
Pen-Tablet and Touch Digitizer Front Ends
The ADC12L030CIWM/NOPB is a natural fit for pen-tablet and touch-digitizer front ends, where the plus-sign 12-bit format captures the small bipolar signals from a stylus coil with high relative accuracy and the SAR architecture offers zero-latency single-shot conversion so each scan-line sample maps directly to one pixel. The 3.3V supply and low power allow battery-powered tablets to run the ADC continuously without draining the cell. Use the self-calibration routine on power-up to cancel pen-coil offset drift, and read the data through the MICROWIRE interface to the host MCU. Compared with an integrating ADC, this SAR part eliminates the 1/LINE_TIME trade-off, giving smoother strokes at high scan rates.
Рекомендуется
Instrumentation and Sensor Signal Conditioning
For instrumentation front ends such as weigh scales, strain-gauge amplifiers, and thermocouple cold-junction compensation, the ADC12L030CIWM/NOPB provides 12-bit plus sign resolution from a 3.3V single supply, allowing the analog front end to use a single op-amp gain stage and a 2.5V reference. The on-chip self-calibration removes DAC nonlinearity and offset at every power-up, which is critical for ratiometric measurements where gain error translates directly to readout error. Drive the ADC's A/DIN1 input with the conditioned sensor signal through a 1kHz RC anti-alias filter, and clock the conversion with the host MCU's SPI peripheral. Compared with lower-resolution 10-bit ADCs, the extra 2 bits of plus-sign resolution reduce quantization noise by 4x and improve panel-meter readability by 24 dB.
Рекомендуется
HVAC and Building Automation Sensor Nodes
In HVAC and building-automation sensor nodes, the ADC12L030CIWM/NOPB digitizes temperature, humidity, and pressure sensors with a 12-bit plus sign dynamic range from a 3.3V supply, supporting the 0-10V or 4-20 mA analog inputs common to commercial controls. The 16-SOIC package is hand-solderable and easy to field-replace, which simplifies service calls, and the industrial -40C to +85C rating covers unconditioned equipment rooms. Use the on-chip MUX to scan 1 sensor channel with built-in self-calibration so the node stays accurate across seasonal swings without periodic field-trim visits. Compared with a 24-bit sigma-delta ADC, this 12-bit SAR part is roughly 10x cheaper and consumes less current, which is appropriate where 0.1% absolute accuracy is not required.
Рекомендуется
Remote Sensor Monitoring with I2C/SPI Bridge
Use the ADC12L030CIWM/NOPB at the analog end of a remote sensor node where a host MCU streams MICROWIRE/SPI conversions over a wireless or wired backhaul. The 3.3V single-supply operation, low power, and on-chip sample/hold let the node run from a small solar cell or two AA cells for years. The 12-bit plus sign format covers a wide dynamic range so one ADC handles both the millivolt-level sensor output and the volt-level supply monitor without an external PGA. Compared with a 16-bit SAR, the 12-bit plus sign ADC trades 4 ENOB for a 30-50% lower price and a 2-3x faster sample rate, which fits a remote node that wakes, samples, transmits, and sleeps within 100 ms.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADC12L030CIWM/NOPB — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADC12L032CIWM/NOPB | ADC12L034CIWM/NOPB | ADC12L038CIWM/NOPB | ADC12030CIWM/NOPB | ADC121S021CIMMX |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments (National Semiconductor) | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SOIC (IWM, 7.50 mm) | 16-SOIC (IWM) - same | 16-SOIC (IWM) - same | 16-SOIC (IWM) - same | 16-SOIC (IWM) - same | 16-SOIC (IWM) - same |
| Resolution | 12-bit + sign | 12-bit + sign | 12-bit + sign | 12-bit + sign | 12-bit + sign | 12-bit (no sign) |
| Architecture | SAR | SAR | SAR | SAR | SAR | SAR |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 5 V | 2.7-5.25 V |
| Input Channels | 1 (MUX configurable to 8) | 2 | 4 | 8 | 1 | 1 |
| Self-Calibration | Yes (on power-up and on demand) | Yes | Yes | Yes | Yes | No (auto-zeroed in modern part) |
| Data Interface | MICROWIRE / SPI | MICROWIRE / SPI | MICROWIRE / SPI | MICROWIRE / SPI | MICROWIRE / SPI | SPI |
| Operating Temperature | -40 C to +85 C (industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Lifecycle | NRND | NRND | NRND | NRND | Active | Active |
Ключевые отличия
- Family member with 1 input channel, allows upgrade to 2/4/8 channels without PCB change (против ADC12L038CIWM/NOPB)
- 12-bit plus sign format extends dynamic range without bipolar supply (против ADC121S021CIMMX)
- On-chip self-calibration eliminates external trims and field re-calibration (против ADC12030CIWM/NOPB)
- Wide-body 16-SOIC (IWM) supports hand-soldering and legacy field service (против ADC121S021CIMMX (MSOP-10))
Заметки по проектированию
The ADC12L030CIWM/NOPB operates from a single 3.3V supply, with separate AVDD and DVDD pins to isolate the sensitive analog charge-redistribution DAC from the digital switching currents. Place a 0.1uF ceramic bypass capacitor as close as possible (within 2-3 mm) to each AVDD pin and another on DVDD, and add a 10uF bulk capacitor at the regulator output. A ferrite bead between AVDD and DVDD, or a small RC filter on AVDD, can further reduce digital-noise coupling into the analog reference. Estimated: with VDD=3.3V and active current around 1-2 mA from the family datasheet, dissipation is roughly 3-7 mW, so no heatsinking is required.
Use a star-ground topology: route AGND and DGND as separate traces back to a single point near the ADC's ground pin or the regulator ground, so that the digital return currents of the SPI/MICROWIRE interface do not flow through the analog ground return of the reference. Place the external reference (or TL431ACDBZR equivalent) and its bypass capacitor adjacent to the VREF pin, and keep the MUXOUT1/MUXOUT2/A/DIN1/A/DIN2 traces short and surrounded by AGND guard traces. Avoid routing DOUT, SCLK, and CS parallel to the analog input traces; if they must cross, do so at 90 degrees. For best 12-bit performance, dedicate one PCB layer as a continuous ground plane and place the ADC in the analog-only section of the board.
Add a simple RC anti-alias filter on the A/DIN1 input, with R=100 ohm and C=1nF giving a 1.6 MHz cutoff that comfortably exceeds the SAR sample rate while attenuating broadband noise. Keep DOUT, SCLK, and CS as short as possible, and add a 33 ohm series resistor at SCLK if the host MCU is more than 50 mm away. Drive CS low only during a conversion frame; bouncing CS during a conversion can cause the SAR to reset. Per the family datasheet, allow the self-calibration to complete (one full conversion cycle) before reading the first data word, or the first sample will be invalid.
Common pitfalls to avoid: (1) applying a 5V input to the analog pins when VDD=3.3V, which exceeds the absolute-maximum rating; (2) omitting the bypass capacitors on AVDD, which causes severe gain and linearity error; (3) tying AGND to DGND through a long thin trace, which creates a ground loop that injects digital switching noise into the analog reference; (4) reading the first conversion before the power-up self-calibration has completed, which yields an offset data word; (5) sharing the same reference as a high-current load, which modulates VREF and adds 50/60 Hz mains noise. Estimated: with a 1kHz sample rate and a properly bypassed 3.3V rail, ENOB should be around 11.5 bits when the input is within 0-VREF.
Информация о соответствии
RoHS compliant per TI/National Semiconductor product page. Not AEC-Q100 qualified (industrial temperature grade only). Halogen-free status not explicitly stated in available web data - marked unknown.
