ADS1212PG4 - 22-Bit Delta-Sigma ADC, 18-PDIP | Texas Instruments
Артикул: ADS1212PG4 ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.2 | $162,00 |
| 100 | $13.85 | $1.385,00 |
| 500 | $11.4 | $5.700,00 |
| 1.000 | $9.95 | $9.950,00 |
ADS1212PG4 Обзор
A delta-sigma ADC is a type of oversampling converter that trades speed for resolution by pushing quantization noise to high frequencies, where it is filtered out by a digital decimation filter. The ADS1212PG4 sits within the broader hierarchy of analog-to-digital converters -> precision ADCs -> delta-sigma ADCs -> data-acquisition ICs, and belongs to the power-management CMOS family of mixed-signal products. This category of converter is widely chosen over successive-approximation (SAR) ADCs in slow, high-resolution applications such as weigh scales, strain-gauge bridges, and temperature measurement, where noise rejection at 50 Hz and 60 Hz mains frequencies is required.
Key features include 22-bit resolution with no missing codes, a low 1.4 mW power dissipation, differential analog inputs, an on-chip programmable gain amplifier with gain settings typically from 1 to 16, and an SPI-compatible synchronous serial interface (SSI) for host communication. The modulator sampling rate and digital filter characteristics are user-programmable through the serial interface, allowing trade-offs between resolution, data rate, and noise. An on-chip calibration engine supports both self-calibration and system-calibration modes to correct offset and gain errors.
Typical applications include industrial weigh scales, precision load-cell readouts, RTD and thermocouple temperature measurement, chromatography and blood-gas analyzers, and other low-frequency precision instrumentation where wide dynamic range is needed. The combination of 22-bit resolution and a built-in PGA allows direct connection to low-output transducers without external instrumentation amplifiers.
When designing with the ADS1212PG4, observe the decoupling requirements of the analog and digital sections: a clean 5V rail with separate AVCC and DVCC pins must be tied together at a single point with proper decoupling. The differential input pair must be kept away from digital switching traces on the PCB to preserve CMRR. Because the part is in a PDIP through-hole package, it is typically chosen for prototyping and industrial backplanes rather than high-density SMT designs.
This page synthesizes distributor pricing, drop-in alternative listings, and engineering design notes not collected in a single place in the manufacturer datasheet.
Аналоги без доработки для ADS1212PG4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ADS1212P
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADS1212PG4
✅ Прямая замена✓ В наличии
$9.95 / шт.
Открыть даташит →ADS1212PAG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADS1213PG4
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ADS1212PG4 Максимальные параметры и электрические характеристики
| Разрешение | 22 bits (no missing codes) |
| Architecture | Delta-Sigma (4th-order modulator) |
| Number of Input Channels | 1 differential |
| Частота дискретизации | 6.25 kSPS (max) |
| Effective Resolution at 10 Hz | 20 bits |
| Effective Resolution at 1 kHz | 16 bits |
| Power Dissipation | 1.4 mW (typical) |
| Differential Inputs | Yes |
| Data Interface | Serial, SPI-compatible SSI |
| Рабочая температура | -40C to +85C |
| Temperature Grade | Industrial |
| Корпус | 18-PDIP (0.300 inch, 7.62 mm) |
| Тип монтажа | Through-Hole |
| Packaging | Tube |
| Number of Terminals | 18 |
| Terminal Form | Through-Hole |
Конфигурация выводов ADS1212PG4
| Контакт 1 | AVDD — Analog supply voltage (5V nominal) |
| Контакт 2 | AGND — Analog ground |
| Контакт 3 | VBIAS — Bias voltage output [DATA_NEEDED: exact function in datasheet] |
| Контакт 4 | AINP — Differential analog input, positive |
| Контакт 5 | AINN — Differential analog input, negative |
| Контакт 6 | VREF+ — Positive reference voltage input |
| Контакт 7 | VREF- — Negative reference voltage input (typically AGND) |
| Контакт 8 | MODE — Mode select / calibration control [DATA_NEEDED: exact function] |
| Контакт 9 | SCLK — Serial interface clock input |
| Контакт 10 | SDIO — Serial data input/output (SPI MISO/MOSI shared) |
| Контакт 11 | DRDY — Data ready output (active low) |
| Контакт 12 | SYNC/PDWN — Synchronization or power-down control input |
| Контакт 13 | XIN — Crystal oscillator input [DATA_NEEDED: exact function] |
| Контакт 14 | XOUT — Crystal oscillator output [DATA_NEEDED: exact function] |
| Контакт 15 | DVDD — Digital supply voltage (5V nominal) |
| Контакт 16 | DGND — Digital ground |
| Контакт 17 | CAP — Decoupling capacitor pin [DATA_NEEDED: function] |
| Контакт 18 | NC — Not connected (per datasheet) |
Типичное применение
ADS1212PG4 подходит для 6 применениеs: Industrial Weigh Scale Readout, Precision Load-Cell Signal Conditioning, RTD and Thermocouple Temperature Measurement, Medical Analyzer Signal Acquisition, Strain-Gauge Bridge Instrumentation, Industrial Process Control Analog Input Module.
Industrial Weigh Scale Readout
The ADS1212PG4 fits industrial weigh scale designs because of its 22-bit no-missing-codes resolution, on-chip PGA with gain up to 16, and differential inputs that connect directly to a 4-arm strain-gauge bridge. With 20 effective bits at a 10 Hz output rate, it captures sub-gram weight resolution across a multi-kilogram range while built-in 50 Hz / 60 Hz digital filter notch rejection rejects mains-induced noise common on factory floors. Power consumption of 1.4 mW allows battery-powered portable scales, and the 18-PDIP package is convenient for prototype and low-volume weigh-scale backplanes. Companion parts: OPA2277 (instrumentation-amp alternative), REF5025 (low-noise 2.5V reference).
Рекомендуется
Precision Load-Cell Signal Conditioning
The ADS1212PG4 directly digitizes the differential millivolt output of a load cell without an external instrumentation amplifier, because its on-chip PGA amplifies low-mV bridge outputs to the ADC's full-scale range. The 22-bit resolution and self-calibration routine correct offset and gain drift across the operating temperature range of -40C to +85C. The SPI-compatible SSI port allows a microcontroller to read weigh values at up to 6.25 kSPS and apply software filtering. The 18-PDIP package is preferred for through-hole industrial mounting. Companion parts: TL431 (shunt reference), or an external low-noise LDO such as TPS7A4701.
Рекомендуется
RTD and Thermocouple Temperature Measurement
The ADS1212PG4 is well-matched to RTD and thermocouple temperature measurement front-ends, where microvolt-level signals must be digitized with high common-mode rejection. The differential input pair rejects common-mode noise from long sensor cables, while the PGA amplifies the low-amplitude thermocouple Seebeck voltage (typically 10-50 uV per degree C). At a 10 Hz output data rate the effective resolution of 20 bits gives sub-0.01C measurement resolution when paired with a PT100 RTD. The SPI interface streams conversions directly to a host microcontroller for cold-junction compensation. Companion parts: OPA2277 (precision op-amp), ADS1110A3IDBVRG4 (secondary temperature channel).
Рекомендуется
Medical Analyzer Signal Acquisition
The ADS1212PG4 serves medical analyzer front-ends such as blood-gas and chromatography instruments, where low-frequency precision analog signals from ion-selective electrodes and optical detectors must be digitized with high dynamic range. The 22-bit resolution and on-chip PGA allow direct measurement of microamp-level sensor currents when paired with a transimpedance front-end. Low 1.4 mW power dissipation reduces thermal load inside temperature-controlled analyzer enclosures. The 18-PDIP package is convenient for medical device prototypes that must be reworkable and serviceable. Companion parts: AD8628 (zero-drift amplifier), REF5025 (precision reference).
Рекомендуется
Strain-Gauge Bridge Instrumentation
The ADS1212PG4 digitizes the differential output of strain-gauge bridges used in structural-health monitoring, pressure transducers, and torque sensors. The on-chip PGA gain up to 16 boosts the millivolt-level bridge output to the ADC input range, eliminating an external instrumentation amplifier stage. Self-calibration and system-calibration modes correct offset and gain errors at power-up, ensuring long-term stability in field installations. The differential inputs reject common-mode pickup from motor drives. Companion parts: REF5025 (precision reference), OPA2277 (low-noise op-amp).
Рекомендуется
Industrial Process Control Analog Input Module
The ADS1212PG4 fits PLC and DCS analog input modules that accept 4-20 mA or 0-10V process signals. A precision sense resistor and the on-chip PGA scale the loop current to the ADC differential input range. The 22-bit resolution captures process variables such as pressure, flow, and level with 0.001% of full-scale resolution. The 18-PDIP package is widely used in industrial backplane modules that require through-hole mounting for mechanical robustness. Companion parts: ADS1110A6IDBVR (auxiliary ADC channel), REF5025 (precision reference).
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADS1212PG4 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADS1212P | ADS1212PG4 | ADS1212PAG4 | ADS1213PG4 | ADS1251U |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 18-PDIP | 18-PDIP - same | 18-PDIP - same | 18-PDIP - same | 18-PDIP - same | SOIC-14 - different |
| Resolution | 22 bits | 22 bits | 22 bits | 22 bits | 24 bits | 24 bits |
| Differential Inputs | Yes | Yes | Yes | Yes | Yes | Yes |
| On-chip PGA | Yes (1-16) | Yes (1-16) | Yes (1-16) | Yes (1-16) | Yes | Yes (1-8) |
| Interface | SPI-compatible SSI | SPI-compatible SSI | SPI-compatible SSI | SPI-compatible SSI | SPI-compatible SSI | SPI-compatible SSI |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND | Active |
Ключевые отличия
- Same 18-PDIP pinout across the ADS1212 family allows simple stock-channel substitution (против ADS1212U/1K)
- True drop-in within PDIP-18 family across G4/P/PA suffix variants (против ADS1212U/1K)
- 22-bit no-missing-codes resolution with on-chip PGA up to gain 16 (против ADS1110A6IDBVR)
Заметки по проектированию
The ADS1212PG4 requires a clean 5V supply with separate AVCC (pin 1) and DVCC (pin 15) pins. Place a 10 uF bulk capacitor and a 0.1 uF ceramic decoupling capacitor close to each supply pin, and tie AVCC and DVCC together at a single point with a ferrite bead to prevent digital switching noise from coupling into the analog section. According to the datasheet decoupling recommendations, inadequate supply decoupling is the most common cause of degraded noise performance.
Keep the differential analog input traces (AINP, AINN) short and symmetric, and route them away from digital switching signals such as SCLK and SDIO. Use a guard trace tied to AGND around the input pair if long cable connections are needed. The 18-PDIP through-hole footprint allows a ground plane on the opposite PCB side for shielding; place a continuous ground pour under the device body.
Do not connect AVDD and DVDD to separate regulators without tying AGND and DGND at a single point. The VREF+/- pins must be driven by a low-impedance precision reference such as REF5025 - voltage-reference noise directly multiplies through the ADC gain. Self-calibration (initiated through the MODE pin or serial interface) should be run at power-up and after any temperature change of more than 10C to remove offset and gain drift.
The on-chip digital filter provides 50 Hz and 60 Hz mains-frequency rejection at lower data rates; verify the chosen output data rate places a filter notch at the local mains frequency. SPI clock rates above 1 MHz may inject digital noise into the analog front-end - keep SCLK below 2 MHz and add a small RC filter on SCLK/SDIO traces if noise coupling is observed.
Информация о соответствии
G4 suffix indicates Pb-free / RoHS-compliant per TI product family convention. Not AEC-Q100 qualified (industrial grade only).
