ATMEGA164P-20AQR - 16KB Flash 20MHz AVR MCU | Microchip
Артикул: ATMEGA164P-20AQR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.47 | $1,47 |
| 10 | $1.33 | $13,30 |
| 100 | $1.19 | $119,00 |
| 500 | $1.08 | $540,00 |
| 1.000 | $0.97 | $970,00 |
ATMEGA164P-20AQR Обзор
An 8-bit AVR microcontroller is a single-chip processor based on the AVR enhanced RISC architecture, in which most instructions execute in a single clock cycle to deliver throughput close to 1 MIPS per MHz. Within the embedded systems hierarchy it spans microcontroller -> 8-bit MCU -> AVR ATmega family -> picoPower device class, combining CPU, program memory, data memory, and peripherals in one package for cost- and power-sensitive designs.
Key features include read-while-write flash for safe in-application firmware updates, 32 general-purpose I/O lines, 32 general-purpose working registers, and the picoPower low-power CMOS process for aggressive sleep-mode current targets. Peripherals include USARTs, SPI, two-wire interface (I2C-compatible), a 10-bit ADC with 8 channels, timers/PWM, and an on-chip debug/ICSP path compatible with MPLAB SNAP.
Architecturally, the ATmega164P pairs the AVR RISC core with Harvard memory organization, allowing simultaneous program and data access; the datasheet (Atmel-42742) documents in-system programmable flash and the full peripheral register set. The single-cycle execution model lets designers trade clock speed directly against power consumption.
Typical applications include industrial control nodes, consumer appliances, sensor and actuator interfaces, and battery-powered instrumentation where 5V logic compatibility and 20 MIPS headroom are needed.
Design consideration: pin-compatible migration across the ATmega164P/324P/644P family is supported (see Microchip application note AVR505), so flash footprint can be scaled without a PCB change.
This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для ATMEGA164P-20AQR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA164P-20AQR (тот же форм-фактор и посадочное место) — отличается по Package, EEPROM, Packaging, SRAM, Core Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATMEGA164P-20AUR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ATMEGA164PA-AUR
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$2.05 / шт.
Открыть даташит →ATMEGA164A-AUR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ATMEGA324P-20AUR
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.52 / шт.
Открыть даташит →ATMEGA164P-15AT
✅ Прямая замена✓ В наличии
$2.35 / шт.
Открыть даташит →ATMEGA1608-AUR
✅ Прямая замена✓ В наличии
$0.92 / шт.
Открыть даташит →ATMEGA164P-20AQR Максимальные параметры и электрические характеристики
| Core Architecture | 8-bit AVR RISC |
| Flash Memory | 16 KB (8K x 16) ISP Flash with read-while-write |
| EEPROM | 512 B |
| SRAM | 1 KB |
| Максимальная тактовая частота | 20 MHz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Throughput | Up to 20 MIPS (1 MIPS per MHz) |
| General Purpose I/O | 32 lines |
| Working Registers | 32 general purpose |
| Корпус | 44-TQFP (10x10 mm) |
| Тип монтажа | Surface Mount |
| Packaging | Tape & Reel (R suffix) |
| Debug / Programming | ICSP via 2 I/O pins + reset; MPLAB SNAP compatible |
| Low Power Technology | picoPower |
| Product Status | Active |
Конфигурация выводов ATMEGA164P-20AQR
| Контакт 1 | PB5 — Port B bit 5 / T1 timer input |
| Контакт 2 | PB6 — Port B bit 6 / T2 timer input |
| Контакт 3 | PB7 — Port B bit 7 / OC0A / XTAL2 alternate |
| Контакт 4 | RESET — Active-low reset input (also ICSP) |
| Контакт 5 | VCC — Digital supply voltage |
| Контакт 6 | GND — Digital ground |
| Контакт 7 | XTAL2 — Crystal oscillator output |
| Контакт 8 | XTAL1 — Crystal oscillator input / external clock |
| Контакт 9 | PD0 — Port D bit 0 / RXD0 (USART0 receive) |
| Контакт 10 | PD1 — Port D bit 1 / TXD0 (USART0 transmit) |
| Контакт 11 | PD2 — Port D bit 2 / INT0 external interrupt |
| Контакт 12 | PD3 — Port D bit 3 / INT1 external interrupt |
| Контакт 13 | PD4 — Port D bit 4 / XCK0 / T0 |
| Контакт 14 | VCC — Digital supply voltage |
| Контакт 15 | GND — Digital ground |
| Контакт 16 | PD5 — Port D bit 5 / XCK1 / OC1A |
| Контакт 17 | PD6 — Port D bit 6 / ICP1 input capture |
| Контакт 18 | PD7 — Port D bit 7 / OC2A / OC1B |
| Контакт 19 | PC0 — Port C bit 0 / SCL (two-wire interface clock) |
| Контакт 20 | PC1 — Port C bit 1 / SDA (two-wire interface data) |
| Контакт 21 | PC2 — Port C bit 2 / TCK (JTAG test clock) |
| Контакт 22 | PC3 — Port C bit 3 / TMS (JTAG test mode select) |
| Контакт 23 | PC4 — Port C bit 4 / TDO (JTAG test data out) |
| Контакт 24 | PC5 — Port C bit 5 / TDI (JTAG test data in) |
| Контакт 25 | PC6 — Port C bit 6 / TOSC1 (RTC oscillator in) |
| Контакт 26 | PC7 — Port C bit 7 / TOSC2 (RTC oscillator out) |
| Контакт 27 | AVCC — Analog supply for ADC (connect to VCC via filter) |
| Контакт 28 | GND — Analog ground |
| Контакт 29 | AREF — ADC analog reference input |
| Контакт 30 | PA7 — Port A bit 7 / ADC7 analog input |
| Контакт 31 | PA6 — Port A bit 6 / ADC6 analog input |
| Контакт 32 | PA5 — Port A bit 5 / ADC5 analog input |
| Контакт 33 | PA4 — Port A bit 4 / ADC4 analog input |
| Контакт 34 | PA3 — Port A bit 3 / ADC3 analog input |
| Контакт 35 | PA2 — Port A bit 2 / ADC2 analog input |
| Контакт 36 | PA1 — Port A bit 1 / ADC1 analog input |
| Контакт 37 | PA0 — Port A bit 0 / ADC0 analog input |
| Контакт 38 | PB0 — Port B bit 0 / SS (SPI slave select) |
| Контакт 39 | PB1 — Port B bit 1 / SCK (SPI clock) |
| Контакт 40 | PB2 — Port B bit 2 / MOSI (SPI data out) |
| Контакт 41 | PB3 — Port B bit 3 / MISO (SPI data in) |
| Контакт 42 | PB4 — Port B bit 4 / OC0 PWM output |
| Контакт 43 | VCC — Digital supply voltage |
| Контакт 44 | GND — Digital ground |
Типичное применение
ATMEGA164P-20AQR подходит для 6 применениеs: Industrial Control Nodes, Battery-Powered Instrumentation, Consumer Appliances, Sensor and Actuator Interfaces, Embedded Debug and Education Boards, Motor Control and PWM Systems.
Industrial Control Nodes
The ATMEGA164P-20AQR fits industrial control nodes because its 32 GPIO lines, 20 MHz throughput (up to 20 MIPS), and 5.5V tolerant supply let it directly interface relays, optocouplers, and 5V logic without level shifting. Its two USARTs and SPI allow robust RS-485 or Modbus connectivity via an external transceiver. Using picoPower sleep modes between polling cycles reduces board-level power, and the read-while-write flash supports field firmware updates over the bus. Place the MCU between the transceiver and I/O driver stages with 100 nF decoupling per VCC pin; the trade-off versus a 32-bit MCU is fewer MIPS but far lower complexity and BOM cost.
Рекомендуется
Battery-Powered Instrumentation
For battery-powered meters and portable instruments, the ATMEGA164P's picoPower CMOS technology minimizes current draw in idle and power-down modes, while the 1 MIPS-per-MHz architecture lets designers clock the part at just 1-4 MHz and still meet response deadlines, cutting active current proportionally. The 10-bit ADC with 8 channels handles sensor inputs directly, and the 512 B EEPROM stores calibration constants without external memory. Running from 2.7V allows two-cell alkaline or single Li-ion operation. Use the internal RC oscillator at low speeds and reserve the 20 MHz crystal for measurement bursts; this hybrid clocking strategy is the primary power-optimization lever on this device.
Рекомендуется
Consumer Appliances
Home appliances such as coffee machines, fans, and small heating controllers benefit from the ATMEGA164P-20AQR's combination of 32 GPIO, timer/PWM resources, and 5V I/O for driving TRIAC triggers, buttons, and 7-segment displays. The 16 KB flash accommodates button-debounce state machines, display multiplexing, and safety interlock logic with headroom for OTA-style field updates via read-while-write flash programming. Its commercial temperature grade matches typical indoor appliance environments. PWM outputs from the on-chip timers directly control motor speed or heater duty cycles without external controllers. The AQR tape-and-reel suffix supports automated SMT lines in volume production, keeping per-unit cost near the $1.47 single-unit level.
Рекомендуется
Sensor and Actuator Interfaces
The ATMEGA164P-20AQR serves as an intelligent sensor hub: its 8-channel 10-bit ADC digitizes analog sensors such as thermistors and potentiometers, while the two-wire interface (I2C-compatible) and SPI connect digital sensors like accelerometers or RTCs. Outputs drive actuators through PWM-capable timer pins, and two USARTs bridge to host systems. The 1 KB SRAM buffers sample arrays for local filtering, and EEPROM stores thresholds and compensation tables. Scanning the ADC with the internal reference and sleeping between samples keeps average current low in picoPower silicon. Design caution: keep analog sensor traces away from the SPI/USART clock lines to preserve the ADC's effective resolution.
Рекомендуется
Embedded Debug and Education Boards
Because the ATmega164P supports in-circuit debugging and ICSP through only two I/O pins plus reset via MPLAB SNAP, it is well suited to evaluation boards, university labs, and hobbyist kits. The classic AVR architecture, free toolchains, and 408-page datasheet (Atmel-42742) provide a gentle learning curve, while the 16 KB flash and 20 MHz clock leave room for meaningful student projects such as UART terminals, ADC oscilloscope demos, and SPI experiments. The 44-TQFP package exposes all 32 I/O lines for breadboard adapters. Boards should route a standard 6-pin ISP header and include a socketed or easily replaced MCU to tolerate beginner wiring mistakes.
Рекомендуется
Motor Control and PWM Systems
The ATMEGA164P-20AQR's multiple timer/PWM channels make it effective for small motor control: DC motor speed, servo positioning, and stepper sequencing can be generated on hardware PWM outputs, offloading the CPU for communication and safety logic. The 20 MHz clock gives 8-bit PWM resolution at high carrier frequencies for quiet motor operation, and the interrupt structure handles quadrature encoder inputs on INT0/INT1 pins. Its 5.5V supply ceiling aligns with gate-driver logic levels for external MOSFET bridges. Compare against a dedicated motor-driver MCU: for single-motor 5V systems the AVR's cost and simplicity win, while multi-axis field-oriented control requires a more powerful part.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA164P-20AQR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA164P-20AUR | ATMEGA164PA-AUR | ATMEGA324P-20AUR | ATMEGA164P-15AT |
|---|---|---|---|---|---|
| Package | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 16 KB | 16 KB | 16 KB | 32 KB | 16 KB |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 15 MHz |
| EEPROM | 512 B | 512 B | 512 B | 1 KB | 512 B |
| SRAM | 1 KB | 1 KB | 1 KB | 2 KB | 1 KB |
| Low Power Technology | picoPower | picoPower | picoPower (PA revision, lower current) | picoPower | picoPower |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 1.8 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
Ключевые отличия
- picoPower silicon for lowest standby current (против ATMEGA164A-AUR)
- Full 20 MHz speed grade (против ATMEGA164P-15AT)
- Field-upgradable memory architecture (против ATMEGA324P-20AUR)
- Extended supply range in PA variant (против ATMEGA164PA-AUR)
Заметки по проектированию
Decouple all three VCC pins and the AVCC pin with 100 nF ceramic capacitors placed within 5 mm of each pin, plus one 10 uF bulk capacitor near the supply entry. Connect AVCC to VCC through an LC filter (10 uH + 100 nF) when ADC accuracy matters, and tie AREF to ground through 100 nF when using the internal reference. The 44-TQFP exposed copper is not an exposed pad, so a solid ground plane on layer 2 provides the return path.
Do not exceed 20 MHz when VCC is below 4.5V; per the AVR speed-grade convention, full-speed 20 MHz operation requires the upper part of the 2.7V-5.5V range. Also, the AQR suffix is the commercial temperature grade - using it outdoors in industrial extremes invites field failures; select the AUR variant instead. During ICSP, keep reset pulled low before applying the programmer or the running firmware may reconfigure the ISP pins.
Exploit picoPower sleep modes to cut average current: estimated power calculation - at 5V and roughly 5 mA active at 20 MHz (typical-class figure; verify exact value in datasheet Table 'Current Consumption'), duty-cycling with 99% power-down operation reduces average current to near the sleep-mode value. Label: this estimate uses nominal supply and duty cycle as inputs; consult the datasheet electrical characteristics table for exact per-mode currents before finalizing battery sizing.
Keep the crystal within 10 mm of XTAL1/XTAL2 with short direct traces and guard with ground pour. Route the two-wire interface (PC0/PC1) with 4.7k pull-ups and keep it away from the SPI clock (PB1) to avoid crosstalk-induced NACKs. For migration headroom, follow AVR505 (Microchip application note doc8001) footprint conventions so ATmega324P or ATmega644P can replace this part without layout change.
Информация о соответствии
The Q package suffix in Microchip part numbering denotes RoHS-compliant green packaging; detailed REACH and conflict-minerals declarations were not present in the retrieved web data.