ATMEGA165PV-8AN - 8MHz AVR MCU 16KB Flash TQFP-64 | Microchip
Артикул: ATMEGA165PV-8AN ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.85 | $4,85 |
| 10 | $4.38 | $43,80 |
| 100 | $3.95 | $395,00 |
| 500 | $3.58 | $1.790,00 |
| 1.000 | $3.25 | $3.250,00 |
ATMEGA165PV-8AN Обзор
An 8-bit AVR microcontroller is a reduced-instruction-set (RISC) single-chip processor in the broader hierarchy of embedded processors: microcontroller -> MCU -> embedded processor -> semiconductor. ATmega devices execute most of their 131 powerful instructions in a single clock cycle, achieving up to 16 MIPS throughput in the wider family, and combine flash program memory, EEPROM data memory, SRAM, timers, USARTs, an ADC, and general-purpose I/O on one die.
Key features include the advanced AVR RISC architecture with 32 general-purpose working registers, fully static operation, in-system programmable (ISP) flash with high-endurance non-volatile memory segments, a 10-bit ADC, multiple timers with PWM, and dual USARTs for serial communication. The -8A speed grade specifies 8 MHz maximum clock, and the -V supply option supports a wide 1.8V to 5.5V operating range, allowing battery- and 5V-industrial-compatible designs on the same PCB.
The picoPower-class V variant minimizes active and sleep current, while the industrial temperature grade supports operation in demanding environments. The TQFP-64 gull-wing surface-mount package provides 54 general-purpose I/O lines, simplifying designs with many switches, displays, and peripheral interfaces such as SPI, I2C/TWI, and UART links.
Typical applications include industrial control panels, building automation and HVAC controllers, metering equipment, sensor nodes, and legacy Atmel AVR designs undergoing production restarts where drop-in ATmega165 family continuity matters.
Design consideration: at 8 MHz on a 5V rail, keep decoupling capacitors close to the multiple VCC/GND pin pairs (three on TQFP-64) and route the analog supply through AVCC with an RC filter for best ADC accuracy.
This page synthesizes distributor availability, drop-in alternatives, and practical design guidance not found in a single manufacturer datasheet. Pricing references are estimates as of 2026-09-16.
Аналоги без доработки для ATMEGA165PV-8AN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA165PV-8AN (тот же форм-фактор и посадочное место) — отличается по Package, Timers, Flash Memory, RoHS Status, Communication Interfaces.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATMEGA165PA-AU
✅ Прямая замена✓ В наличии
$2.05 / шт.
Открыть даташит →ATMEGA165A-AU
✅ Прямая замена✓ В наличии
$3.47 / шт.
Открыть даташит →ATMEGA165PV-8AU
✅ Прямая замена✓ В наличии
$2.49 / шт.
Открыть даташит →ATMEGA165P-16ANR
✅ Прямая замена✓ В наличии
$2.18 / шт.
Открыть даташит →ATMEGA165PA-AN
✅ Прямая замена✓ В наличии
$2.19 / шт.
Открыть даташит →ATMEGA165PV-8AN Максимальные параметры и электрические характеристики
| Core Architecture | AVR 8-bit RISC |
| Core Size | 8-bit |
| Максимальная тактовая частота | 8 MHz |
| Flash Memory | 16 KB (8K x 16) in-system programmable |
| EEPROM | 512 B |
| SRAM | 1 KB |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Instruction Set | 131 instructions, most single-cycle |
| Number of I/Os | 54 |
| Корпус | 64-TQFP (14x14 mm), gull wing, square |
| Тип монтажа | Surface Mount |
| Temperature Grade | Industrial |
| Adc | 10-bit ADC present |
| Communication Interfaces | USART, SPI, TWI (I2C) |
| Timers | On-chip timers with PWM |
| Статус RoHS | Compliant (Green package) |
| Program Memory Type | FLASH, high-endurance non-volatile |
Конфигурация выводов ATMEGA165PV-8AN
| Контакт 1 | PE0 (RXD0/PDI) — Port E bit 0 / USART0 receive |
| Контакт 2 | PE1 (TXD0/PDO) — Port E bit 1 / USART0 transmit |
| Контакт 3 | PE2 (XCK0/AIN0) — Port E bit 2 / USART0 clock / analog comparator input 0 |
| Контакт 4 | PE3 (OC3A/AIN1) — Port E bit 3 / Timer3 output compare A / comparator input 1 |
| Контакт 5 | PE4 (OC3B/INT4) — Port E bit 4 / Timer3 output compare B / external interrupt 4 |
| Контакт 6 | PE5 (OC3C/INT5) — Port E bit 5 / Timer3 output compare C / external interrupt 5 |
| Контакт 7 | PE6 (T3/INT6) — Port E bit 6 / Timer3 clock input / external interrupt 6 |
| Контакт 8 | PE7 (ICP3/CLK0/INT7) — Port E bit 7 / Timer3 input capture / interrupt 7 |
| Контакт 9 | GND — Digital ground |
| Контакт 10 | VCC — Digital supply voltage |
| Контакт 11 | PG0 (WR) — Port G bit 0 / external memory write strobe |
| Контакт 12 | PG1 (RD) — Port G bit 1 / external memory read strobe |
| Контакт 13 | PC0 (A8) — Port C bit 0 / external memory address line |
| Контакт 14 | PC1 (A9) — Port C bit 1 / external memory address line |
| Контакт 15 | PC2 (A10) — Port C bit 2 / external memory address line |
| Контакт 16 | PC3 (A11) — Port C bit 3 / external memory address line |
| Контакт 17 | PC4 (A12) — Port C bit 4 / external memory address line |
| Контакт 18 | PC5 (A13) — Port C bit 5 / external memory address line |
| Контакт 19 | PC6 (A14) — Port C bit 6 / external memory address line |
| Контакт 20 | PC7 (A15) — Port C bit 7 / external memory address line |
| Контакт 21 | GND — Digital ground |
| Контакт 22 | VCC — Digital supply voltage |
| Контакт 23 | PD0 (SCL/INT0) — Port D bit 0 / TWI clock / external interrupt 0 |
| Контакт 24 | PD1 (SDA/INT1) — Port D bit 1 / TWI data / external interrupt 1 |
| Контакт 25 | PD2 (RXD1/INT2) — Port D bit 2 / USART1 receive / external interrupt 2 |
| Контакт 26 | PD3 (TXD1/INT3) — Port D bit 3 / USART1 transmit / external interrupt 3 |
| Контакт 27 | PD4 (ICP1) — Port D bit 4 / Timer1 input capture |
| Контакт 28 | PD5 (XCK1) — Port D bit 5 / USART1 external clock |
| Контакт 29 | PD6 (T1) — Port D bit 6 / Timer1 external clock input |
| Контакт 30 | PD7 (T2) — Port D bit 7 / Timer2 external clock input |
| Контакт 31 | PG2 (ALE) — Port G bit 2 / external memory address latch enable |
| Контакт 32 | GND — Digital ground |
| Контакт 33 | VCC — Digital supply voltage |
| Контакт 34 | PA0 (AD0) — Port A bit 0 / ADC channel 0 / external memory data bus |
| Контакт 35 | PA1 (AD1) — Port A bit 1 / ADC channel 1 / external memory data bus |
| Контакт 36 | PA2 (AD2) — Port A bit 2 / ADC channel 2 / external memory data bus |
| Контакт 37 | PA3 (AD3) — Port A bit 3 / ADC channel 3 / external memory data bus |
| Контакт 38 | PA4 (AD4) — Port A bit 4 / ADC channel 4 / external memory data bus |
| Контакт 39 | PA5 (AD5) — Port A bit 5 / ADC channel 5 / external memory data bus |
| Контакт 40 | PA6 (AD6) — Port A bit 6 / ADC channel 6 / external memory data bus |
| Контакт 41 | PA7 (AD7) — Port A bit 7 / ADC channel 7 / external memory data bus |
| Контакт 42 | AVCC — Analog supply voltage for ADC and Port F |
| Контакт 43 | PF0 (ADC0) — Port F bit 0 / ADC channel 0 |
| Контакт 44 | PF1 (ADC1) — Port F bit 1 / ADC channel 1 |
| Контакт 45 | PF2 (ADC2) — Port F bit 2 / ADC channel 2 |
| Контакт 46 | PF3 (ADC3) — Port F bit 3 / ADC channel 3 |
| Контакт 47 | PF4 (ADC4/TCK) — Port F bit 4 / ADC channel 4 / JTAG test clock |
| Контакт 48 | PF5 (ADC5/TMS) — Port F bit 5 / ADC channel 5 / JTAG test mode select |
| Контакт 49 | PF6 (ADC6/TDO) — Port F bit 6 / ADC channel 6 / JTAG test data out |
| Контакт 50 | PF7 (ADC7/TDI) — Port F bit 7 / ADC channel 7 / JTAG test data in |
| Контакт 51 | AREF — Analog reference voltage for ADC |
| Контакт 52 | GND — Analog ground |
| Контакт 53 | AVCC — Analog supply voltage |
| Контакт 54 | PB0 (SS) — Port B bit 0 / SPI slave select |
| Контакт 55 | PB1 (SCK) — Port B bit 1 / SPI serial clock |
| Контакт 56 | PB2 (MOSI) — Port B bit 2 / SPI master data out |
| Контакт 57 | PB3 (MISO) — Port B bit 3 / SPI master data in |
| Контакт 58 | PB4 (OC2A/PCINT4) — Port B bit 4 / Timer2 output compare A / pin change interrupt |
| Контакт 59 | PB5 (OC1A/PCINT5) — Port B bit 5 / Timer1 output compare A / pin change interrupt |
| Контакт 60 | PB6 (OC1B/PCINT6) — Port B bit 6 / Timer1 output compare B / pin change interrupt |
| Контакт 61 | PB7 (OC0A/OC1C/PCINT7) — Port B bit 7 / Timer0 output compare A / Timer1 output compare C / pin change interrupt |
| Контакт 62 | PG3 (TOSC2) — Port G bit 3 / Timer oscillator output (32 kHz RTC crystal) |
| Контакт 63 | PG4 (TOSC1) — Port G bit 4 / Timer oscillator input (32 kHz RTC crystal) |
| Контакт 64 | XTAL1/XTAL2 — Main oscillator pins - verify exact XTAL1/XTAL2 split against datasheet |
Типичное применение
ATMEGA165PV-8AN подходит для 6 применениеs: Industrial Control Panels, Building Automation and HVAC Controllers, Metering and Measurement Equipment, Sensor Nodes and Data Loggers, Legacy Atmel Design Production Restarts, Automotive and Marine Instrument Clusters.
Industrial Control Panels
The ATMEGA165PV-8AN fits industrial control panels because its 54 GPIO lines drive relays, contactors, indicator lamps, and keypad matrices directly, while the 10-bit ADC reads potentiometer-setpoints and sensor channels without an external converter. The dual USARTs allow simultaneous connection of an HMI display and a Modbus RTU link on one chip, and the industrial temperature grade covers cabinet environments. Operating at 8 MHz from a 5V industrial rail provides deterministic single-cycle instruction execution for time-critical interlock logic, and the 16 KB flash holds ladder-style control code with room for bootloader updates via the ISP interface.
Рекомендуется
Building Automation and HVAC Controllers
In building automation and HVAC controllers, the ATMEGA165PV-8AN combines a wide 1.8V-5.5V supply range, TWI (I2C) for temperature and humidity sensors, and timer PWM outputs for damper and valve actuation on a single 64-pin TQFP device. The picoPower-class V variant keeps standby current low so a controller can run from a backup battery during outages, while the 1 KB SRAM handles protocol buffers for networked communication. The 16 KB in-system-programmable flash supports field firmware updates over the serial link, an important serviceability feature for rooftop units, air handlers, and zone controllers deployed for long service lifetimes.
Рекомендуется
Metering and Measurement Equipment
The ATMEGA165PV-8AN suits utility metering and measurement equipment because its 10-bit ADC with AVCC filtering digitizes current-transformer and voltage-divider channels, while timers capture pulse outputs from energy meters. The 8 MHz clock is slow enough for low EMI in dense meter PCBs yet sufficient for RMS computation of 50/60 Hz waveforms. EEPROM retains calibration constants and consumption logs through power loss, and the TQFP-64's many I/O lines interface to LCD segments, optical comm ports, and tamper switches. The wide supply range tolerates the sagging supplies typical of meter power circuits derived from the mains.
Рекомендуется
Sensor Nodes and Data Loggers
For battery-powered sensor nodes and data loggers, the ATMEGA165PV-8AN's V-suffix supply range (1.8V-5.5V) allows direct operation from two alkaline cells or a single lithium cell through the full discharge curve. The picoPower-class design sleeps in power-down mode between samples, waking on timer or external interrupt to convert a sensor with the 10-bit ADC and log results to EEPROM or external flash over SPI. At 8 MHz active processing is brief, so average current is dominated by sleep current - the key figure of merit for multi-year battery life in agricultural monitoring, cold-chain logging, and environmental telemetry deployments.
Рекомендуется
Legacy Atmel Design Production Restarts
Many legacy products designed around the Atmel ATmega165 in the early 2000s require production restarts today. The ATMEGA165PV-8AN is the currently supported Microchip Technology part number for that design: identical die-level function, TQFP-64 footprint, and AVR instruction set, so existing firmware compiled in avr-gcc or IAR rebuilds without porting. BOM managers can also qualify the ATMEGA165PA-AU as a second source on the same land pattern, following Microchip's official alternate-part guidance for ATmega MCUs to mitigate the periodic allocation this legacy family experiences.
Рекомендуется
Automotive and Marine Instrument Clusters
Instrument clusters and dash gauges use the ATMEGA165PV-8AN where its many I/O lines drive stepper-gauge motors and warning lamps, the ADC samples fuel and temperature senders, and USARTs link to the vehicle body controller. The industrial-grade temperature spec and fully static core (operation can be clocked down or stopped safely) fit the harsh electrical environment after load-dump protection circuitry. The 8 MHz rating keeps radiated emissions within limits for EMC-sensitive cabin electronics, and the JTAG interface supports in-circuit firmware updates during vehicle service without removing the cluster from the dashboard.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA165PV-8AN — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA165PA-AU | ATMEGA165A-AU | ATMEGA165PV-8AU | ATMEGA165P-16AN |
|---|---|---|---|---|---|
| Package | 64-TQFP (14x14 mm) | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP (14x14 mm) - same | 64-TQFP - same |
| Brand | Microchip Technology (Atmel) | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology (Atmel) |
| Flash Memory | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| Power Feature | picoPower-class V variant | picoPower A-generation | Standard grade | picoPower V variant | Standard P grade |
| Temperature Grade | Industrial | Industrial | Industrial | Industrial | Industrial |
Ключевые отличия
- Wide 1.8V-5.5V supply range on one design (против ATMEGA165P-16AN)
- More I/O than the ATmega164 subfamily (против ATMEGA164PV-10PU)
- picoPower-class consumption with full family compatibility (против ATMEGA165PA-AU)
Заметки по проектированию
The TQFP-64 ATMEGA165PV-8AN has multiple VCC/GND pin pairs (pins 9/10, 21/22, 32/33); place a 100 nF ceramic capacitor within 2-3 mm of each pair plus one 4.7-10 uF bulk capacitor at the supply entry. Follow the Microchip AVR hardware design considerations application note for the decoupling topology. Poor decoupling on this family shows up as ADC noise and sporadic flash corruption during programming, so treat the decoupling network as a critical, not optional, part of the layout.
Connect AVCC (pins 42/53) to the digital rail through a small RC filter (e.g., 10 ohm series resistor plus 100 nF to ground) and tie AREF to its recommended decoupling when using the internal reference. Never leave AVCC unconnected even if the ADC is unused - the Port F I/O and JTAG cells depend on it. Estimated: keeping analog ripple below 1 LSB of a 10-bit ADC on a 5 V rail means keeping AVCC noise under about 4.9 mV.
Verify the speed grade before substitution: the -8A suffix limits the clock to 8 MHz, while the ATMEGA165P-16AN allows 16 MHz - fitting a 16 MHz crystal to this part will cause out-of-spec operation and unreliable USART timing. Also note the JTAG pins are shared with ADC4-ADC7 on Port F: if your design uses those ADC channels, disable JTAG via the fuse bits after programming, otherwise the pins are held in JTAG mode at reset.
Информация о соответствии
Mouser and DigiKey list the part as 'GRN' (green/halogen-free, RoHS-compliant) package. AEC-Q100 qualification is not indicated in the provided data for this industrial-grade part.
