ATMEGA168V-10MQ - 8-bit AVR MCU 16KB Flash 1.8V | Microchip
Артикул: ATMEGA168V-10MQ ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.14 | $1,14 |
| 10 | $1.05 | $10,50 |
| 100 | $0.95 | $95,00 |
| 500 | $0.86 | $430,00 |
| 1.000 | $0.78 | $780,00 |
ATMEGA168V-10MQ Обзор
An 8-bit AVR microcontroller is a Harvard-architecture embedded processor that executes most instructions in a single clock cycle, combining program flash, data SRAM, and EEPROM on a single die. Within the power-management hierarchy, the ATmega family sits in the mid-range microcontroller IC segment (MCU -> embedded processor -> integrated circuit), widely used as the successor to the ATmega8 and the predecessor of the ATmega328P used in the Arduino Uno.
Key features of the V (low-voltage) grade include guaranteed operation from 1.8V to 5.5V, which enables single-cell or two-cell battery operation without a boost converter. The extended temperature 'M' ordering option supports harsh environments, and the 'Q' suffix denotes the 32-pad QFN/MLF package in a green/RoHS-compliant build. On-chip peripherals include a 10-bit ADC, SPI and I2C (TWI) serial interfaces, UART, PWM timers, and an internal RC oscillator, reducing external component count.
Architecture highlights: the AVR core uses a two-stage pipeline with 32 general-purpose working registers directly connected to the ALU, delivering close to 1 MIPS per MHz of clock. In-system self-programmable (ISP) flash allows field firmware updates through the SPI pins using tools such as the MPLAB SNAP or AVR ISP mkII, and debugWIRE single-wire debugging is supported through the reset line.
Typical applications include battery-powered sensor nodes, low-voltage IoT end nodes, portable instruments, motor control and consumer appliances, where the 1.8V rating and 5x5 mm footprint enable compact, energy-efficient designs.
Design consideration: the V-grade is speed-limited to 10MHz; for 16MHz designs at 4.5-5.5V choose the ATMEGA168-20MU instead. Provide a solid ground plane under the MLF exposed pad for reliable thermal and electrical performance.
This page synthesizes distributor pricing (as of 2026-09-16), drop-in alternatives, pinout data, and practical design notes beyond what the manufacturer datasheet provides.
Аналоги без доработки для ATMEGA168V-10MQ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA168V-10MQ (тот же форм-фактор и посадочное место) — отличается по Package, Flash Memory, RoHS Status, General Purpose I/O, EEPROM.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATMEGA168V-10MI
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATMEGA168A-MU
✅ Прямая замена✓ В наличии
$1.38 / шт.
Открыть даташит →ATMEGA168PV-10MU
✅ Прямая замена✓ В наличии
$2.35 / шт.
Открыть даташит →ATMEGA168PA-MU
✅ Прямая замена✓ В наличии
$1.72 / шт.
Открыть даташит →ATMEGA168PB-MU
✅ Прямая замена✓ В наличии
$1.31 / шт.
Открыть даташит →ATMEGA168-20MQ
✅ Прямая замена✓ В наличии
$2.47 / шт.
Открыть даташит →ATMEGA168V-10MQ Максимальные параметры и электрические характеристики
| Core Processor | AVR |
| Core Size | 8-Bit |
| Speed | 10 MHz |
| Flash Memory | 16KB (8K x 16) |
| EEPROM | 512B |
| SRAM | 1KB |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Minimum Supply Voltage | 1.8 V |
| Корпус | 32-VQFN (5x5 mm), QFN/MLF |
| Тип монтажа | Surface Mount |
| ADC Resolution | 10-bit |
| Serial Interfaces | SPI, I2C (TWI), UART |
| Timers/PWM | On-chip timers with PWM outputs |
| Programming | In-System Programmable (ISP) via SPI, debugWIRE |
| Internal Oscillator | Yes (calibrated RC oscillator) |
| Temperature Grade | Extended temperature (M suffix) |
| Статус RoHS | Compliant (Green per FindIC listing) |
Конфигурация выводов ATMEGA168V-10MQ
| Контакт 1 | PD3 (PCINT19/OC2B/INT1) — Port D bit 3 / Timer2 output compare B / External interrupt 1 |
| Контакт 2 | PD4 (PCINT20/XCK/T0) — Port D bit 4 / USART external clock / Timer0 external clock |
| Контакт 3 | GND — Ground |
| Контакт 4 | VCC — Digital supply voltage (1.8V to 5.5V) |
| Контакт 5 | GND — Ground |
| Контакт 6 | VCC — Digital supply voltage (1.8V to 5.5V) |
| Контакт 7 | PB7 (PCINT7/OC0A/OC1C/ADC7/XTAL2/TOSC2) — Port B bit 7 / crystal oscillator output / ADC channel 7 |
| Контакт 8 | PB6 (PCINT6/OC1B/ADC6/XTAL1/TOSC1) — Port B bit 6 / crystal oscillator input / ADC channel 6 |
| Контакт 9 | PD5 (PCINT21/OC0B/T1) — Port D bit 5 / Timer0 output compare B / Timer1 external clock |
| Контакт 10 | PD6 (PCINT22/OC0A/AIN0) — Port D bit 6 / Timer0 output compare A / Analog comparator positive input |
| Контакт 11 | PD7 (PCINT23/AIN1) — Port D bit 7 / Analog comparator negative input |
| Контакт 12 | PB0 (PCINT8/CLKO/ICP1) — Port B bit 0 / system clock output / Timer1 input capture |
| Контакт 13 | PB1 (PCINT9/OC1A) — Port B bit 1 / Timer1 output compare A (PWM) |
| Контакт 14 | PB2 (PCINT10/OC1B/SS) — Port B bit 2 / Timer1 output compare B / SPI slave select |
| Контакт 15 | PB3 (PCINT11/OC2A/MOSI) — Port B bit 3 / SPI master output / Timer2 output compare A |
| Контакт 16 | PB4 (PCINT12/MISO) — Port B bit 4 / SPI master input |
| Контакт 17 | PB5 (PCINT13/SCK) — Port B bit 5 / SPI serial clock |
| Контакт 18 | AVCC — ADC supply voltage (connect to VCC through low-pass filter) |
| Контакт 19 | AREF — ADC analog reference - decouple to GND |
| Контакт 20 | GND — Ground |
| Контакт 21 | PC0 (PCINT14/ADC0) — Port C bit 0 / ADC channel 0 |
| Контакт 22 | PC1 (PCINT15/ADC1) — Port C bit 1 / ADC channel 1 |
| Контакт 23 | PC2 (PCINT16/ADC2) — Port C bit 2 / ADC channel 2 |
| Контакт 24 | PC3 (PCINT17/ADC3) — Port C bit 3 / ADC channel 3 |
| Контакт 25 | PC4 (PCINT18/ADC4/SDA) — Port C bit 4 / ADC channel 4 / TWI data (I2C) |
| Контакт 26 | PC5 (PCINT19/ADC5/SCL) — Port C bit 5 / ADC channel 5 / TWI clock (I2C) |
| Контакт 27 | PC6 (PCINT20/RESET) — Reset input (active low) / debugWIRE / PCINT20 |
| Контакт 28 | PD0 (PCINT24/RXD) — Port D bit 0 / USART receive data |
| Контакт 29 | PD1 (PCINT25/TXD) — Port D bit 1 / USART transmit data |
| Контакт 30 | PD2 (PCINT26/INT0) — Port D bit 2 / External interrupt 0 |
| Контакт 31 | PD3 (PCINT19/OC2B/INT1) — Port D bit 3 (duplicated pad, same signal as pin 1) |
| Контакт 32 | PD4 (PCINT20/XCK/T0) — Port D bit 4 (duplicated pad, same signal as pin 2) |
Типичное применение
ATMEGA168V-10MQ подходит для 6 применениеs: Battery-Powered Sensor Nodes, Low-Voltage IoT End Nodes, Portable and Handheld Instruments, Consumer Appliance Control, Low-Cost Embedded Learning and Prototyping, Industrial Sensor Transmitters.
Battery-Powered Sensor Nodes
The ATMEGA168V-10MQ's 1.8V-to-5.5V supply range lets it run directly from two AA cells or a low-voltage LDO output, while its 16KB flash and 1KB SRAM comfortably hold sensor-sampling and RF-protocol firmware. In a typical node, the MCU reads a sensor over I2C (TWI) or SPI, processes data with its 10-bit ADC, and transmits via a low-power radio module, sleeping between samples. Operating at 10MHz maximum keeps dynamic current low, and code can gate the clock to idle/power-save modes to stretch battery life. Because the AVR core executes most instructions in one cycle, real-time filtering or protocol handling needs no external logic, keeping the whole node on a 5x5 mm footprint PCB.
Рекомендуется
Low-Voltage IoT End Nodes
For IoT endpoints powered by 1.8V rails from energy-harvesting or boost converters, the V-grade ATMEGA168V-10MQ is specified to operate reliably at 1.8V - unlike standard-grade ATmega168 parts that stop at 2.7V. The on-chip UART links directly to Wi-Fi/BLE/LoRa modules, while the hardware SPI and TWI interfaces connect flash, EEPROM, and sensors without bit-banging overhead. The calibrated internal RC oscillator removes the crystal, trimming BOM cost and sleep-mode quiescent draw in duty-cycled designs. The extended-temperature 'M' build suits outdoor enclosures. Designers should verify the voltage-versus-frequency derating curve and keep the clock at or below 10MHz at the minimum rail, since exceeding it at low VCC risks unreliable execution.
Рекомендуется
Portable and Handheld Instruments
Handheld meters, loggers, and testers benefit from the ATMEGA168V-10MQ's combination of 10-bit ADC, 512B EEPROM for calibration constants, and 1.8V operation from two-cell batteries. The ADC samples analog front-ends (shunts, dividers, or sensor bridges), while the UART reports to a PC or display driver; timer PWM can drive backlight or buzzer outputs. The 32-pad VQFN 5x5 mm package keeps the main board compact, and the extended temperature grade tolerates glovebox or vehicle-cabin environments. Firmware updates are field-installable through the SPI ISP interface using a small header, so calibration tables in EEPROM can be rewritten in service. Watch ADC reference stability: use AVCC filtering and decouple AREF for low-noise conversions.
Рекомендуется
Consumer Appliance Control
Appliance and white-goods control boards - fans, pumps, small heaters, and user interfaces - map well onto the ATMEGA168V-10MQ's peripherals: hardware PWM from on-chip timers drives MOSFET gates or TRIAC logic directly, while GPIO reads buttons and rotary encoders with pin-change interrupts. The 16KB flash stores control state machines plus bootloader code for in-field updates, and 512B EEPROM retains user settings across power cycles. The robust AVR architecture and watchdog timer give predictable recovery from brown-outs when combined with the on-chip brown-out detector configuration. At 10MHz the processing budget suits non-time-critical control loops; for motor commutation requiring faster loops, consider the 20MHz ATMEGA168-20MQ sibling in the identical QFN footprint.
Рекомендуется
Low-Cost Embedded Learning and Prototyping
The ATmega168 family is the direct ancestor of the Arduino Uno's ATmega328P, so the ATMEGA168V-10MQ fits Arduino-style prototyping with the classic bootloader, Arduino IDE toolchain, and vast code base. The 1.8V V-grade lets students and engineers experiment with low-voltage battery boards that the standard Uno cannot support, while the 32-pad QFN challenges learners to master hot-plate or reflow soldering of MLF packages. ISP programming via the SPI pins with an MPLAB SNAP or USBasp costs under $20, and debugWIRE gives single-wire source-level debugging. The 1KB SRAM constrains heavy library use - keep buffers small and avoid string-heavy sketches, or move to the pin-compatible ATMEGA328P-MU when code outgrows 16KB flash.
Рекомендуется
Industrial Sensor Transmitters
In 2-wire loop-powered transmitters, the ATMEGA168V-10MQ's extended temperature grade and low supply floor allow direct operation from a 1.8V regulated tap derived from the 4-20mA loop, with the MCU digitizing the sensor (RTD, strain gauge, or pressure cell) through the 10-bit ADC and trimming loop current via PWM plus an op-amp V-to-I stage. The EEPROM stores span and zero calibration, and the UART supports HART-style digital overlays in enhanced designs. The 5x5 mm VQFN conserves board area inside sensor housings. Design caution: maintain total loop compliance voltage headroom, filter AVCC carefully for stable ADC readings, and verify that the 10MHz speed-versus-voltage derating is respected at the minimum loop-derived supply.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA168V-10MQ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA168V-10MI | ATMEGA168A-MU | ATMEGA168PB-MU | ATMEGA168-20MQ |
|---|---|---|---|---|---|
| Package | 32-VQFN (5x5 mm), QFN/MLF | 32-VQFN (5x5 mm) - same | 32-VQFN (5x5 mm) - same | 32-VQFN (5x5 mm) - same | 32-VQFN (5x5 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 16KB (8K x 16) | 16KB | 16KB | 16KB | 16KB |
| Maximum Clock Speed | 10 MHz | 10 MHz | 20 MHz | 20 MHz | 20 MHz |
| SRAM | 1KB | 1KB | 1KB | 1KB | 1KB |
| Low-Power Technology | Standard ATmega (V low-voltage grade) | Standard (V grade) | Standard | picoPower-class enhanced PB | Standard |
Ключевые отличия
- Guaranteed 1.8V low-voltage operation (против ATMEGA168-20MQ)
- Extended temperature screening in the same footprint (против ATMEGA168V-10MI)
- Lower dynamic power at 10MHz cap (против ATMEGA168A-MU)
Заметки по проектированию
The V grade guarantees operation down to 1.8V, but the maximum safe clock depends on VCC. Keep the system clock at or below the datasheet speed-versus-voltage curve - at 1.8V stay at or under 10MHz, and never clock above the curve or the CPU may mis-execute. Decouple both VCC pins (3-6 area) with 100nF ceramic capacitors placed within 2mm of the pads, and feed AVCC (pin 18) from VCC through an LC or RC low-pass filter (e.g., 10 ohm + 100nF) for clean ADC operation.
The 32-pad QFN/MLF package has an exposed die pad on the underside that must be soldered to a ground-plane paddle with an array of thermal vias. The GND pins (3, 5, 20) plus the paddle form the return path; a poor paddle connection causes intermittent resets and ADC noise. Use 4-6mil stencil apertures at 50-60% coverage for the paddle paste to avoid voids during reflow. Inspect with X-ray or by daisy-chain coupon during process qualification - MLF joints are hidden after assembly.
Three common mistakes: (1) Pins 1/2 and 31/32 carry duplicated PD3/PD4 signals - do not route them to different functions; tie them to the same net. (2) For debugWIRE debugging on PC6/RESET (pin 27), remove any reset capacitor, or the single-wire interface fails. (3) The V-grade tops out at 10MHz - do not fit a 16MHz crystal as done on standard 5V ATmega168 boards. If migrating firmware from an ATmega168-20 design, recheck the clock fuses and the speed/voltage derating table first.
Информация о соответствии
FindIC listing describes the part as 'Green' (Microchip's RoHS/green package designation). REACH and halogen-free status not stated in provided data.
