ATSAMD20J15A-MNT - 32KB Flash Cortex-M0+ MCU | Microchip | 64-QFN
Артикул: ATSAMD20J15A-MNT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.5 | $2,50 |
| 10 | $2.25 | $22,50 |
| 100 | $2.01 | $201,00 |
| 500 | $1.82 | $910,00 |
| 1.000 | $1.63 | $1.630,00 |
| 3.000 | $1.45 | $4.350,00 |
ATSAMD20J15A-MNT Обзор
An ARM Cortex-M0+ microcontroller is a low-power 32-bit processor core designed by ARM Holdings for cost-sensitive embedded applications. The Cortex-M0+ belongs to the ARMv6-M architecture family and is the smallest and most energy-efficient core in the Cortex-M lineup, typically featuring single-cycle I/O, a Wake-up Interrupt Controller (WIC), and optional Micro Trace Buffer (MTB). It sits within a hierarchy of microcontroller → embedded processor → semiconductor device, and combines a CPU core with on-chip memory, peripherals, and interrupt controllers on a single silicon die. The SAM D20J family specifically targets low-power connected applications in home automation, consumer, metering, and industrial segments.
The ATSAMD20J15A-MNT integrates the Cortex-M0+ core with 32KB Flash, 4KB SRAM, and the Microchip peripheral set including SERCOM (I2C/SPI/UART), 12-bit ADC, 10-bit DAC, and a full-speed USB 2.0 device controller on the larger-pin variants. The device supports 1.62V to 3.63V operating voltage, multiple low-power sleep modes (IDLE, STANDBY, BACKUP), and a 32.768kHz RTC. Its 48MHz maximum clock with single-cycle multiplier enables responsive control loops while preserving energy budget.
Architecturally, the SAM D20J uses a single-cycle I/O port structure, an event system for inter-peripheral signaling without CPU wake-ups, and a peripheral touch controller (PTC) supporting hardware-driven capacitive sensing. The device is manufactured on a low-leakage process and uses a bundled peripheral event fabric so GPIO, timers, and SERCOM modules can interact autonomously, offloading the core and reducing average power in sensor-driven designs.
Typical applications include battery-powered IoT sensor nodes, smart home automation hubs, industrial metering, consumer human-interface devices, and low-power wireless companion controllers. The Cortex-M0+ + Cortex-M Software Interface Standard (CMSIS) ecosystem and the MPLAB X IDE / Harmony 3 framework simplify firmware migration within the SAM family and to/from PIC MCUs.
A key design consideration is the QFN-64 (9x9) thermal pad - it MUST be soldered to a properly sized thermal copper pour to meet the datasheet's 64-QFN thermal resistance specifications and ensure reliable operation. Designers migrating from the SAM D20 to the SAM D21 family (Cortex-M0+ to Cortex-M0+ upgrade) gain DMA and faster ADC, but the pinout is largely compatible.
This page synthesizes distributor pricing, drop-in SAM D20J family alternatives, and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для ATSAMD20J15A-MNT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATSAMD20J15A-MNT (тот же форм-фактор и посадочное место) — отличается по Package, SRAM, ADC, Operating Temperature Range, Core Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATSAMD20J16A-MNT
✅ Прямая замена✓ В наличии
$2.18 / шт.
Открыть даташит →ATSAMD20J18A-MNT
✅ Прямая замена✓ В наличии
$3.41 / шт.
Открыть даташит →ATSAMD20J14A-MNT
✅ Прямая замена✓ В наличии
$1.18 / шт.
Открыть даташит →ATSAMD20J15A-MN
✅ Прямая замена✓ В наличии
$0.85 / шт.
Открыть даташит →ATSAMD20G15A-MNT
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ATSAMD20J15A-MNT Максимальные параметры и электрические характеристики
| Core Processor | ARM Cortex-M0+ |
| Core Architecture | ARMv6-M |
| Core Size | 32-Bit Single-Core |
| Максимальная тактовая частота | 48 MHz |
| CoreMark/MHz | 2.14 |
| Program Memory (Flash) | 32 KB (32K x 8) |
| SRAM | 4 KB |
| Operating Voltage Range | 1.62 V to 3.63 V |
| Supply Voltage (Typ.) | 3.3 V |
| Корпус | 64-QFN (9x9 mm) with Exposed Pad |
| Тип монтажа | Surface Mount |
| Connectivity | I2C, SPI, UART/USART |
| Peripherals | Brown-out Detect/Reset, POR, WDT, 12-bit ADC, 10-bit DAC, RTC |
| Number of I/O | 52 |
| Диапазон рабочих температур | -40 C to +85 C (industrial) |
| Уровень MSL | MSL3 |
| Статус RoHS | Compliant |
| Series | SAM D20J |
Руководство по цоколевке ATSAMD20J15A-MNT в корпусе 64-qfn (9x9 mm) with exposed pad
Цоколевка для ATSAMD20J15A-MNT (корпус 64-qfn (9x9 mm) with exposed pad). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для ATSAMD20J15A-MNT.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ATSAMD20J15A-MNT подходит для 6 применениеs: Battery-Powered IoT Sensor Node, Smart Home Automation Hub, Industrial Metering and Data Logging, Consumer Human-Interface Device (HID), Low-Power Wireless Companion Controller, Educational and Maker Electronics Platform.
Battery-Powered IoT Sensor Node
The ATSAMD20J15A-MNT is well-suited for battery-powered IoT sensor nodes thanks to its Cortex-M0+ core's 2.14 CoreMark/MHz efficiency and the SAM D20 family's multiple low-power sleep modes. With a 48MHz max clock and 1.62-3.63V operating range, the MCU can run directly from a single CR2032 coin cell (3V) or single-cell Li-ion (3.7V nominal) without a boost regulator. The integrated 12-bit ADC and SERCOM-based I2C/SPI interfaces let the MCU read sensors while the event system wakes the core only on peripheral triggers, achieving typical sleep currents under 5 uA in STANDBY mode. Compared to an 8-bit AVR at the same task, the Cortex-M0+ reduces active time and extends battery life 2-3x. Recommended companion parts include the ATECC608B secure element for authentication and the SAM R34 LoRa transceiver for sub-GHz connectivity.
Рекомендуется
Smart Home Automation Hub
In smart home automation hubs, the ATSAMD20J15A-MNT serves as a low-cost node controller that aggregates sensor inputs and drives relays, MOSFETs, or TRIAC outputs. The 52 GPIO pins and multiple SERCOM peripherals (I2C/SPI/UART) support concurrent connectivity to Zigbee modules, Wi-Fi co-processors, and multiple sensor chains. The 48MHz clock and 32KB Flash comfortably run protocols like Zigbee 3.0 host stacks, Matter-over-Thread bridge logic, or simple MQTT-SN firmware. The SAM D20 family's peripheral event system allows GPIO interrupts to wake the core from STANDBY in microseconds, enabling ultra-low-power always-listening designs. The 64-QFN (9x9) package integrates cleanly into compact hub PCBs alongside Wi-Fi/BT modules.
Рекомендуется
Industrial Metering and Data Logging
The ATSAMD20J15A-MNT fits industrial metering applications requiring precise analog measurement and reliable data retention. Its 12-bit ADC with up to 12 input channels handles voltage, current, and temperature sensing on electricity, gas, and water meters. The 32KB Flash and 4KB SRAM support metering firmware plus time-stamped logging using the on-chip RTC with 32.768kHz crystal input. The 1.62-3.63V supply range allows direct operation from 3.3V regulated rails common in industrial PLCs, while the industrial -40 C to +85 C temperature rating handles outdoor cabinet environments. Migration paths within the SAM D20 family preserve firmware when scaling meter variants by memory size (D20J14/J15/J16/J18).
Рекомендуется
Consumer Human-Interface Device (HID)
For consumer HIDs such as touch-button appliances, remote controls, and capacitive-touch user interfaces, the ATSAMD20J15A-MNT integrates the Peripheral Touch Controller (PTC) for up to 12 self-capacitive or mutual-capacitive touch channels. The Cortex-M0+ runs at up to 48MHz with deterministic interrupt response, enabling responsive touch decoding at low power. The 12-bit DAC drives audio feedback tones, while SERCOM peripherals connect to LED drivers and small displays. Compared to discrete touch ICs, integrating touch on the MCU reduces BOM cost by 30-50% on consumer products.
Рекомендуется
Low-Power Wireless Companion Controller
The ATSAMD20J15A-MNT operates as a sensor-hub companion to a wireless module such as SAM R34 or RN4870 BLE. The MCU aggregates analog sensor data via its 12-bit ADC, performs local filtering or threshold decisions, and forwards events to the wireless module via UART or SPI. By keeping the wireless radio in deep sleep until the ATSAMD20J15A-MNT wakes it, designers achieve battery life of 1-3 years on a single CR2032 cell. The Cortex-M0+ core's single-cycle I/O port and fast interrupt wake-up (under 1.5 us from STANDBY) make this MCU ideal for event-driven sensor designs.
Рекомендуется
Educational and Maker Electronics Platform
The ATSAMD20J15A-MNT is supported by the open-source Arduino Zero / M0 Pro platform and the Adafruit Feather M0 ecosystem, providing extensive library and tutorial support for education. Its Cortex-M0+ architecture with 32KB Flash and 4KB SRAM offers a stepping stone between 8-bit AVR and higher-end Cortex-M4 designs. The SAM D20's peripheral event system, DMA-like SERCOM, and 12-bit ADC give students hands-on experience with modern 32-bit MCU concepts. The 64-QFN package is breadboard-adaptable via breakout boards, while native Arduino IDE / PlatformIO support reduces onboarding friction.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATSAMD20J15A-MNT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATSAMD20J16A-MNT | ATSAMD20J18A-MNT | ATSAMD20J14A-MNT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same |
| Flash Memory | 32 KB | 32 KB (identical) | 256 KB (+700%) | 16 KB (-50%) |
| SRAM | 4 KB | 4 KB (identical) | 32 KB (+700%) | 2 KB (-50%) |
| Max Clock Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Operating Voltage | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V | 1.62 V to 3.63 V |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Ключевые отличия
- Higher memory in same 64-QFN footprint (против ATSAMD20J18A-MNT)
- Identical die, lower shipping cost (против ATSAMD20J15A-MN)
- Industry-standard Cortex-M0+ toolchain (против PIC16F677-I/P (8-bit PIC))
- Lower memory for cost-optimized designs (против ATSAMD20J14A-MNT)
Заметки по проектированию
The ATSAMD20J15A-MNT uses a 64-QFN package (9x9 mm) with an exposed thermal pad (EP) that MUST be soldered to a PCB copper pour to meet the datasheet's thermal resistance specification. For designs dissipating more than 200 mW continuously, allocate at least 1 square inch of top-layer copper tied to the EP and stitch via arrays to internal ground planes. Without proper EP soldering, junction-to-ambient thermal resistance rises sharply and may trigger thermal shutdown under heavy GPIO loading.
Place a 0.1 uF X7R decoupling capacitor within 2 mm of each VDDCORE and VDDIO pin pair, plus a single 4.7 uF bulk capacitor near the package. The SAM D20 power manager requires POR (power-on-reset) and BOD (brown-out-detector) to be enabled in NVMUSERROW fuses for reliable operation; disable only if external supervisor IC is used. Estimated: the SAM D20's IDLE current is ~2 mA at 48 MHz / 3.3 V; STANDBY current ~5 uA with RTC running.
Do NOT connect unused SAM D20 GPIO pins directly to ground - per Microchip errata and the SAM D20 datasheet, unused pins should be configured as outputs driven low or inputs with internal pull enabled. Floating inputs can cause current spikes up to 100 uA per pin during supply transitions. Also note the I/O drive strength register must be set before high-speed SERCOM operation - default drive strength is too low for >10 MHz SPI reliably.
Route the 32.768 kHz crystal traces (XIN32/XOUT32) as short as possible (under 5 mm) with guard ground on both sides, and place load capacitors (typically 12-22 pF) within 2 mm of the MCU. The DFLL reference (if used) is sensitive to noise; route its reference clock away from switching power and SERCOM lines. Always use a 4-layer PCB or at minimum a 2-layer PCB with a continuous ground plane for SAM D20 designs to minimize EMI on the analog ADC inputs.
Информация о соответствии
RoHS and REACH compliance per Microchip product page. Standard industrial grade (-40 C to +85 C); AEC-Q100 automotive variants are in the SAM D20 -AUT family. MSL3 moisture sensitivity level. Conflict-minerals disclosure filed annually by Microchip.
