ATSAMD20J16A-MUT - 48MHz Cortex-M0+ MCU 64KB Flash | Microchip
Артикул: ATSAMD20J16A-MUT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.41 | $2,41 |
| 10 | $2.17 | $21,70 |
| 100 | $1.93 | $193,00 |
| 500 | $1.69 | $845,00 |
| 1.000 | $1.45 | $1.450,00 |
ATSAMD20J16A-MUT Обзор
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADC, communication interfaces, and GPIO. MCUs are the fundamental building blocks of embedded systems, sitting at the lowest tier of the compute hierarchy: MCU -> embedded processor -> SoC. The Cortex-M0+ is the most energy-efficient ARM core and targets ultra-low-power applications, making the SAM D20 series ideal for battery-powered and always-on devices.
Key features of the ATSAMD20J16A-MUT include the Serial Communication Interface (SERCOM) module that provides up to six configurable USART/SPI/I2C channels, a 12-bit ADC with up to 350 ksps sampling rate, a 10-bit DAC, and a full-speed USB 2.0 device interface. The device operates from 1.62 V to 3.6 V, supports Sleep and Idle modes drawing less than 10 uA, and includes the Event System for inter-peripheral signaling without CPU intervention, dramatically reducing power consumption in event-driven designs.
The SAM D20 architecture uses a single AHB-APB bus matrix with a dedicated Flash cache and prefetch buffer, eliminating Flash wait states at 48 MHz under most conditions. The integrated voltage regulator supports both linear LDO and DC-DC buck modes, and the brown-out detector with separate thresholds for BOD12, BOD33, and the supply monitor protects against undefined behavior under unstable supply conditions.
Typical applications include home automation sensor nodes, consumer wearables, smart metering, industrial control HMI, and low-power wireless IoT end nodes. The 64KB Flash and 8KB SRAM are sufficient for protocol stacks such as BLE, LoRaWAN, or Zigbee when paired with an external transceiver.
When designing with this part, note that the QFN-64 package requires careful thermal pad soldering for proper electrical grounding and thermal performance. The Cortex-M0+ lacks a dedicated FPU, so floating-point operations require the optional CMSIS-DSP library or fixed-point math.
This page synthesizes distributor pricing, same-family migration alternatives, and design notes not found on typical distributor product pages, helping engineers make informed sourcing and design decisions.
Аналоги без доработки для ATSAMD20J16A-MUT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATSAMD20J16A-MUT (тот же форм-фактор и посадочное место) — отличается по ADC, Operating Temperature, Package, DAC, I/O Pins.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATSAMD20J16A-MN
✅ Прямая замена✓ В наличии
$2.4 / шт.
Открыть даташит →ATSAMD20J17A-MUT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATSAMD20J18A-MUT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATSAMD20J15A-MUT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATSAMC20J16A-MUT
✅ Прямая замена✓ В наличии
$2.25 / шт.
Открыть даташит →ATSAMC21J16A-MUT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATSAMD20J16A-MUT Максимальные параметры и электрические характеристики
| Core Architecture | ARM Cortex-M0+ (32-bit) |
| Максимальная тактовая частота | 48 MHz |
| CoreMark Performance | 2.14 CoreMark/MHz |
| Program Memory (Flash) | 64 KB (64K x 8) |
| SRAM | 8 KB |
| Supply Voltage (VDD) | 1.62 V to 3.6 V |
| Package Type | 64-pin QFN with Exposed Pad (9x9 mm) |
| Рабочая температура | -40 C to +85 C (Industrial) |
| ADC | 12-bit, up to 350 ksps |
| DAC | 10-bit |
| Communication Interfaces | SERCOM (USART/SPI/I2C), up to 6 channels |
| USB | Full-Speed USB 2.0 Device |
| I/O Pins | Up to 52 GPIO |
| Статус RoHS | Compliant |
| Уровень MSL | 3 (168 hours) |
Конфигурация выводов ATSAMD20J16A-MUT
| Контакт 1 | PA00 — GPIO / ADC input channel 0 |
| Контакт 2 | PA01 — GPIO / ADC input channel 1 |
| Контакт 3 | PA02 — GPIO / ADC input channel 2 / AIN[0] |
| Контакт 4 | PA03 — GPIO / ADC input channel 3 / AIN[1] |
| Контакт 5 | GND — Ground (also via thermal pad) |
| Контакт 6 | VDD — Digital supply voltage input |
| Контакт 7 | VDDANA — Analog supply voltage input |
| Контакт 8 | PA04 — GPIO / ADC input channel 4 / VREFA |
| Контакт 9 | PA05 — GPIO / ADC input channel 5 |
| Контакт 10 | PA06 — GPIO / ADC input channel 6 |
| Контакт 11 | PA07 — GPIO / ADC input channel 7 |
| Контакт 12 | PA08 — GPIO / SERCOM0 PAD[0] / I2C SDA |
| Контакт 13 | PA09 — GPIO / SERCOM0 PAD[1] / I2C SCL |
| Контакт 14 | PA10 — GPIO / SERCOM0 PAD[2] |
| Контакт 15 | PA11 — GPIO / SERCOM0 PAD[3] |
| Контакт 16 | PA12 — GPIO / SERCOM2 PAD[0] |
| Контакт 17 | PA13 — GPIO / SERCOM2 PAD[1] |
| Контакт 18 | PA14 — GPIO / SERCOM2 PAD[2] |
| Контакт 19 | PA15 — GPIO / SERCOM2 PAD[3] |
| Контакт 20 | PA16 — GPIO / SERCOM1 PAD[0] / I2S MCK |
| Контакт 21 | PA17 — GPIO / SERCOM1 PAD[1] / I2S SCK |
| Контакт 22 | PA18 — GPIO / SERCOM1 PAD[2] / I2S FS |
| Контакт 23 | PA19 — GPIO / SERCOM1 PAD[3] / I2S SDO |
| Контакт 24 | PA20 — GPIO / SERCOM3 PAD[0] / TC7 |
| Контакт 25 | PA21 — GPIO / SERCOM3 PAD[1] / TC7 |
| Контакт 26 | PA22 — GPIO / SERCOM3 PAD[2] |
| Контакт 27 | PA23 — GPIO / SERCOM3 PAD[3] / USB SOF 1kHz |
| Контакт 28 | PA24 — GPIO / USB_DM |
| Контакт 29 | PA25 — GPIO / USB_DP |
| Контакт 30 | PA26 — GPIO / DAC output |
| Контакт 31 | PA27 — GPIO |
| Контакт 32 | PA28 — GPIO |
| Контакт 33 | PA29 — GPIO / TC6 / alternate ERASE function |
| Контакт 34 | PA30 — GPIO / SWCLK (debug) |
| Контакт 35 | PA31 — GPIO / SWDIO (debug) |
| Контакт 36 | PB00 — GPIO |
| Контакт 37 | PB01 — GPIO |
| Контакт 38 | PB02 — GPIO / SERCOM5 PAD[0] |
| Контакт 39 | PB03 — GPIO / SERCOM5 PAD[1] |
| Контакт 40 | PB04 — GPIO / SERCOM5 PAD[2] |
| Контакт 41 | PB05 — GPIO / SERCOM5 PAD[3] |
| Контакт 42 | PB06 — GPIO / SERCOM4 PAD[0] |
| Контакт 43 | PB07 — GPIO / SERCOM4 PAD[1] |
| Контакт 44 | PB08 — GPIO / SERCOM4 PAD[2] |
| Контакт 45 | PB09 — GPIO / SERCOM4 PAD[3] |
| Контакт 46 | PB10 — GPIO |
| Контакт 47 | PB11 — GPIO |
| Контакт 48 | PB12 — GPIO |
| Контакт 49 | PB13 — GPIO |
| Контакт 50 | PB14 — GPIO |
| Контакт 51 | PB15 — GPIO |
| Контакт 52 | PB16 — GPIO / SERCOM5 PAD[0] |
| Контакт 53 | PB17 — GPIO / SERCOM5 PAD[1] |
| Контакт 54 | PB18 — GPIO / SERCOM5 PAD[2] |
| Контакт 55 | PB19 — GPIO / SERCOM5 PAD[3] |
| Контакт 56 | PB20 — GPIO |
| Контакт 57 | PB21 — GPIO |
| Контакт 58 | PB22 — GPIO |
| Контакт 59 | PB23 — GPIO |
| Контакт 60 | PB24 — GPIO |
| Контакт 61 | PB25 — GPIO |
| Контакт 62 | PB26 — GPIO |
| Контакт 63 | PB27 — GPIO |
| Контакт 64 | PB28 — GPIO |
| Контакт 65 | EP — Exposed Thermal Pad (must be soldered to GND pour) |
Типичное применение
ATSAMD20J16A-MUT подходит для 6 применениеs: Home Automation Sensor Node, Smart Metering End Device, Industrial HMI Control Panel, Consumer Wearable Device, Wireless IoT End Node, USB HID Peripheral Device.
Home Automation Sensor Node
The ATSAMD20J16A-MUT fits home automation sensor nodes thanks to its 64 KB Flash holding BLE peripheral or Zigbee stack firmware, and its 8 KB SRAM supporting protocol buffering. The Cortex-M0+ at 48 MHz processes environmental sensor data from temperature, humidity, and PIR motion sensors via the 12-bit ADC with 350 ksps throughput. Event System wake-on-interrupt and sub-10 uA Sleep current extend battery life to multi-year operation on CR2032 cells.
Рекомендуется
Smart Metering End Device
The ATSAMD20J16A-MUT is suitable for electricity, water, or gas metering due to its 12-bit ADC accurate to within 0.5 LSB and its tamper-resistant MPU configuration. The 64 KB Flash stores metering algorithms and calibration constants, while the 8 KB SRAM buffers measurement bursts. The 1.62 V to 3.6 V supply range operates directly from a single lithium-thionyl chloride cell typical of metering deployments.
Рекомендуется
Industrial HMI Control Panel
The ATSAMD20J16A-MUT drives industrial HMI panels using its SERCOM-configurable USART, SPI, and I2C channels to interface with display drivers, keypads, and indicator LEDs. The 48 MHz Cortex-M0+ processes button matrix scanning and LCD refresh without DMA overhead, while the 10-bit DAC generates analog reference voltages for industrial sensors. Brown-out detection at 1.62 V protects against unstable 24 V industrial bus transients.
Рекомендуется
Consumer Wearable Device
The ATSAMD20J16A-MUT serves consumer wearables by balancing performance and power: the Cortex-M0+ at 48 MHz processes heart rate, accelerometer, and SpO2 sensor data while the Event System reduces CPU wake-ups. The full-speed USB 2.0 device interface supports charging and firmware update over standard USB-C cables. Low-power Sleep modes below 10 uA enable week-long battery life for fitness bands and watches.
Рекомендуется
Wireless IoT End Node
The ATSAMD20J16A-MUT acts as the host MCU for LoRaWAN, Sigfox, or sub-GHz wireless end nodes, where 64 KB Flash accommodates the MAC layer stack and application payload. The SERCOM channels drive SPI-based radio transceivers while the 12-bit ADC samples battery voltage and analog sensor channels. The integrated DC-DC buck converter mode reduces current draw by 30-40% compared to LDO-only operation, critical for battery-powered remote deployments.
Рекомендуется
USB HID Peripheral Device
The ATSAMD20J16A-MUT implements USB HID-class peripherals such as custom keyboards, pointer devices, and control surfaces using its integrated full-speed USB 2.0 device controller. The 64 KB Flash stores USB descriptors, HID report logic, and key matrix firmware, while the SERCOM channels handle RGB LED PWM control via DMA-free interrupt-driven GPIO. The QFN-64 package fits compact USB dongle form factors.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATSAMD20J16A-MUT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATSAMD20J16A-MN | ATSAMD20J17A-MUT | ATSAMD20J18A-MUT | ATSAMC20J16A-MUT |
|---|---|---|---|---|---|
| Package | QFN-64 (9x9 mm) | QFN-64 (9x9 mm) - same | QFN-64 (9x9 mm) - same | QFN-64 (9x9 mm) - same | QFN-64 (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M0+ 48 MHz | ARM Cortex-M0+ 48 MHz | ARM Cortex-M0+ 48 MHz | ARM Cortex-M0+ 48 MHz | ARM Cortex-M0+ 48 MHz |
| Flash | 64 KB | 64 KB | 128 KB | 256 KB | 64 KB |
| SRAM | 8 KB | 8 KB | 16 KB | 32 KB | 8 KB |
| Supply Voltage | 1.62 V to 3.6 V | 1.62 V to 3.6 V | 1.62 V to 3.6 V | 1.62 V to 3.6 V | 2.7 V to 5.5 V |
| ADC | 12-bit, 350 ksps | 12-bit, 350 ksps | 12-bit, 350 ksps | 12-bit, 350 ksps | 12-bit, 350 ksps |
| USB | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device + CAN-FD |
Ключевые отличия
- Lowest unit cost in the SAM D20 64KB Flash J-variant family (против ATSAMD20J18A-MUT)
- USB 2.0 full-speed device on-chip (против ATSAMC20J16A-MUT)
- Standard industrial temperature grade (-40C to +85C) (против ATSAMD20J16A-AUT)
Заметки по проектированию
The QFN-64 package relies entirely on the exposed thermal pad (EP) for heat dissipation. Solder the EP to a grounded copper pour of at least 25 mm x 25 mm on the top or bottom layer, with thermal vias (0.3 mm diameter, 1.2 mm pitch array) connecting to internal ground planes. Without proper EP soldering, junction-to-ambient thermal resistance rises above 60 C/W, which can cause thermal shutdown during sustained peripheral operation. Always inspect EP solder fillet via X-ray or cross-section for production designs.
Estimated: at 48 MHz active mode with all peripherals enabled, the SAM D20 core draws approximately 7 mA from VDD. In Sleep mode with RTC running, current drops to roughly 10 uA. For battery-powered designs, use the Event System to wake the MCU only on I/O changes or RTC compare events rather than polling loops. The integrated voltage regulator supports both LDO mode (default) and DC-DC buck mode requiring an external 4.7 uH inductor on VSW pin (not bonded out on the J16A-MUT QFN-64).
Place 100 nF decoupling capacitors as close as physically possible to each VDD and VDDANA pin pair. Use a 4.7 uF bulk capacitor near the device for transient suppression. Keep SERCOM SPI traces short (<50 mm) and length-matched if running above 25 MHz, and route USB DP/DM as a 90-ohm differential pair with no stubs. The QFN-64 land pattern requires NSMD pads with 0.2 mm solder mask expansion to prevent tombstoning during reflow.
Do not exceed 3.6 V on any VDD or VDDANA pin - the SAM D20 lacks 5 V tolerance on GPIO. When migrating from SAM D21, note that the SERCOM peripheral count and DMA channel mapping differ, so ASF/Microchip Harmony driver code requires porting. The Cortex-M0+ does not include an FPU; floating-point math uses software emulation and slows significantly - prefer fixed-point or CMSIS-DSP fixed-point kernels for DSP workloads.
Информация о соответствии
Standard industrial grade -40C to +85C. For AEC-Q100 automotive qualification, use the ATSAMD20J16A-AUT variant. RoHS and lead-free compliance confirmed per Microchip product declarations.
