ATSAMD51J19A-MFT - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
Артикул: ATSAMD51J19A-MFT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $9.84 | $9,84 |
| 10 | $8.86 | $88,60 |
| 100 | $7.89 | $789,00 |
| 500 | $6.91 | $3.455,00 |
| 1.000 | $5.94 | $5.940,00 |
ATSAMD51J19A-MFT Обзор
A microcontroller (MCU) is a single-chip processor that combines a CPU core, program and data memory, peripherals, and I/O interfaces on one die, enabling embedded systems to perform deterministic control and signal-processing tasks with low BOM cost. The SAM D51 sits in the 32-bit MCU hierarchy above 8-bit (AVR/PIC) and 16-bit (MSP430) cores, below microprocessor units that require external memory, and uses the ARM Cortex-M4F core with FPU for compute-bound motor control, audio, and IoT-edge workloads.
Key features include the 120 MHz Cortex-M4F core with hardware FPU, 512 KB ECC Flash, 192 KB ECC SRAM, integrated USB 2.0 Full-Speed with PHY, an I2S/serial audio interface, up to 6 SERCOM (serial communication) peripherals configurable as UART/SPI/I2C, a 12-bit ADC up to 1 MSPS, a 10-bit DAC, and a built-in cryptographic accelerator supporting AES, SHA, and True Random Number Generator (TRNG). The device supports 1.71V to 3.6V core operation with an on-chip DC-DC buck converter and extensive low-power modes.
Architecturally, the SAM D51 uses a Harvard-style bus matrix connecting the Cortex-M4F core to tightly-coupled memories (TCM) and AHB/APB peripheral bridges, with the dual-panel Flash allowing simultaneous read-while-write and the ECC blocks detecting/correcting single-bit memory faults. The MFT suffix indicates the 64-QFN package plus an industrial temperature grade (-40C to +125C), making it suitable for harsh-environment designs.
Typical applications include industrial motor control (FOC for BLDC/PMSM), USB-based human-interface devices, audio processing and digital signal processing (DSP) overlays, secure IoT edge nodes, and graphical HMI panels. The integrated cryptographic accelerator and TRNG also make it a fit for TLS-enabled IoT devices.
When designing with this device, supply the 1.62-3.6V VDDCORE from the on-chip DC-DC converter output on the correct pin pair, place 4.7uF X7R ceramics at each VDD pin, and route the USB DP/DM traces as a 90-ohm differential pair. Use Atmel Studio / MPLAB X with the ASF4 or Harmony framework to enable SERCOM remapping and avoid pin conflicts.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including cross-package traps (QFN-64 vs TQFP-64) and same-footprint SAMD51 family variants for supply-chain resilience.
Аналоги без доработки для ATSAMD51J19A-MFT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATSAMD51J19A-MFT (тот же форм-фактор и посадочное место) — отличается по ADC, Package, DAC, SRAM, USB.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATSAMD51J19A-MF
✅ Прямая замена✓ В наличии
$5.4 / шт.
Открыть даташит →ATSAMD51G19A-MFT
✅ Прямая замена✓ В наличии
$4.02 / шт.
Открыть даташит →ATSAMD51J19A-AFT
✅ Прямая замена✓ В наличии
$4.8 / шт.
Открыть даташит →ATSAMD51J19A-MFT Максимальные параметры и электрические характеристики
| Core | ARM Cortex-M4F with FPU |
| Maximum CPU Clock | 120 MHz |
| Flash Memory | 512 KB with ECC (dual-panel) |
| SRAM | 192 KB with ECC |
| Supply Voltage (VDD) | 1.71 V to 3.6 V |
| Рабочая температура | -40C to +125C (industrial, -MFT suffix) |
| Корпус | 64-pin QFN (9x9 mm) |
| USB | USB 2.0 Full-Speed with on-chip PHY |
| ADC | 12-bit, up to 1 MSPS |
| DAC | 10-bit, 350 kSPS |
| Serial Communication | 6 SERCOM (UART/SPI/I2C configurable) |
| I2S / Audio | Yes (I2S controller) |
| Cryptography | AES-128/256, SHA-256, TRNG (hardware accelerator) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Руководство по цоколевке ATSAMD51J19A-MFT в корпусе 64-pin qfn (9x9 mm)
Цоколевка для ATSAMD51J19A-MFT (корпус 64-pin qfn (9x9 mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для ATSAMD51J19A-MFT.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ATSAMD51J19A-MFT подходит для 6 применениеs: BLDC / PMSM Motor Control with Field-Oriented Control (FOC), USB Human-Interface Device (HID) and Audio Class Dongle, Secure IoT Edge Node with TLS 1.3 and OTA Updates, Industrial HMI Panel with TFT Display, Medical Sensor Hub with Signal Conditioning, Audio Processing and DSP Effects Unit.
BLDC / PMSM Motor Control with Field-Oriented Control (FOC)
The ATSAMD51J19A-MFT is a natural fit for BLDC and PMSM motor drives running field-oriented control because its 120 MHz Cortex-M4F with single-precision FPU executes the Park/Clarke transforms and PI loops in a single PWM cycle. The integrated 12-bit ADC up to 1 MSPS samples three-phase shunt currents synchronously with the TCC timer, while six SERCOM peripherals handle UART isolators, SPI encoder feedback, and I2C HMI bridges. Hardware AES/SHA accelerates secure boot, and ECC Flash/SRAM supports IEC 61508 SIL-2 designs.
Рекомендуется
USB Human-Interface Device (HID) and Audio Class Dongle
With USB 2.0 Full-Speed PHY integrated, the ATSAMD51J19A-MFT can deliver Audio Class 1.0, HID, CDC, and vendor-specific interfaces without an external PHY, shrinking the BOM by approximately USD 0.85 versus discrete-PHY competitors. The I2S controller can drive a 24-bit stereo CODEC at 48 kHz while the FPU executes dynamics processing such as biquad filtering. The 192 KB SRAM buffers USB isochronous packets without under-runs in portable audio designs.
Рекомендуется
Secure IoT Edge Node with TLS 1.3 and OTA Updates
The ATSAMD51J19A-MFT's hardware AES-256, SHA-256, and True Random Number Generator (TRNG) execute TLS 1.3 handshakes in approximately one-third of the time of a software-only implementation, conserving power in battery-backed IoT endpoints. The dual-panel Flash with ECC supports secure bootloader patterns where a secondary image is validated cryptographically before swap, enabling in-field OTA updates. Six SERCOM peripherals drive concurrent I2C sensors, SPI radios, and UART modems.
Рекомендуется
Industrial HMI Panel with TFT Display
Driving a 480x272 WQVGA TFT panel over the parallel SMC interface, the ATSAMD51J19A-MFT renders 60 fps UIs while the FPU accelerates bitmap blits and anti-aliased fonts. ECC memory catches bit-flip faults common in electrically noisy industrial cabinets, and the -40C to +125C temperature grade (MFT suffix) tolerates cabinet interior heat near power contactors. The I2S interface plays touch-feedback tones alongside the visual UI.
Рекомендуется
Medical Sensor Hub with Signal Conditioning
The ATSAMD51J19A-MFT's 12-bit ADC at 1 MSPS conditions PPG, ECG, or SpO2 signals with hardware DSP features, while its hardware AES secures HIPAA-compliant patient data. ECC memory is a strong fit for IEC 60601-1 risk-management files. The integrated USB PHY enables USB-IF cable-connected patient monitoring stations. Power consumption of 9 mA active at 120 MHz aligns with battery-powered wearable medical device budgets.
Рекомендуется
Audio Processing and DSP Effects Unit
The ATSAMD51J19A-MFT executes 1024-point FFT or convolution reverb in real time on 16-bit / 48 kHz audio streams thanks to the 120 MHz Cortex-M4F with FPU and 192 KB SRAM. The I2S controller sources/clocks external CODECs up to 24-bit and the 10-bit DAC can drive analog headphone-monitoring line-out directly. The 64-QFN package footprint keeps mass-market audio products under tight PCB real estate budgets while -40C to +125C meets rack-mount pro-audio environmental classes.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATSAMD51J19A-MFT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATSAMD51J19A-MF | ATSAMD51G19A-MFT | ATSAMD51J19A-AFT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin QFN (9x9 mm) | 64-pin QFN (9x9 mm) - identical footprint | 64-pin QFN (9x9 mm) - identical footprint | 64-pin TQFP (10x10 mm) - same family, different footprint |
| Core | ARM Cortex-M4F, 120 MHz | ARM Cortex-M4F, 120 MHz | ARM Cortex-M4F, 120 MHz | ARM Cortex-M4F, 120 MHz |
| Flash Memory | 512 KB with ECC | 512 KB with ECC | 512 KB WITHOUT ECC | 512 KB with ECC |
| SRAM | 192 KB with ECC | 192 KB with ECC | 192 KB WITHOUT ECC | 192 KB with ECC |
| Temperature Grade | -40C to +125C (industrial) | 0C to +70C (commercial) | -40C to +125C (industrial) | -40C to +125C (industrial) |
| Cryptographic Accelerator | AES-256 + SHA-256 + TRNG | AES-256 + SHA-256 + TRNG | AES-256 + SHA-256 + TRNG | AES-256 + SHA-256 + TRNG |
| USB | USB 2.0 FS with on-chip PHY | USB 2.0 FS with on-chip PHY | USB 2.0 FS with on-chip PHY | USB 2.0 FS with on-chip PHY |
| Approximate Unit Price @100 | USD 7.89 | USD 7.45 (commercial, lower cost) | USD 7.30 (no-ECC, lower cost) | USD 8.10 (TQFP variant) |
Ключевые отличия
- ECC on Flash and SRAM (vs SAMD51G19A base variant) (против ATSAMD51G19A-MFT)
- Industrial -40C to +125C temperature grade (против ATSAMD51J19A-MF)
- Compact 9x9 mm QFN footprint (против ATSAMD51J19A-AFT)
Заметки по проектированию
Estimated: The ATSAMD51J19A-MFT typically runs from a 3.3V rail and uses its internal DC-DC converter to generate VDDCORE. Place a 4.7uF X7R ceramic on each VDD pin and a 10uH power inductor (L1) between L1/VSW and VDD for the on-chip buck; poor inductor selection (high DCR) causes VDDCORE ripple and ADC reference noise. Decouple VDDCORE with a 1uF + 0.1uF ceramic pair within 5 mm of the pin pair.
Estimated: At 120 MHz / 1.71V the part consumes approximately 9 mA active plus peripherals; the 64-QFN (9x9 mm) Theta-JA from the SAM D5X/E5X datasheet is roughly 28 C/W on a 4-layer JEDEC test board. Derate by 1 mW per degree Celsius above 25C ambient; for sealed enclosures >60C, attach a copper pour of at least 1 sq. inch under the exposed pad. Do not rely on default -MFT industrial temp if heat-sinking is insufficient.
Common pitfalls when designing with the ATSAMD51J19A-MFT: (1) configuring SERCOM pads without GCLK_SEL and locking the bus, (2) forgetting to set FPU lazy stacking to avoid HARD FAULT on interrupt entry for Cortex-M4F, (3) using the same DFLL48M reference for USB and ADC without enabling the USB SOF recovery, which causes ADC jitter. The On-chip DC-DC requires careful inductor selection - reference the SAM D5X/E5X schematics in ASF4 for a known-good circuit.
Route the USB DP/DM pair as a 90-ohm differential with no splits, length-matching within 150 mil. Provide a solid 4-layer ground plane under the 64-QFN exposed pad and stitch vias on a 1-mm grid. Keep the SD-Card or QSPI traces at 50 ohm single-ended, no stubs, with series resistors at the source only if the SI-TDR scan shows ringing above 6 dB. Per the SAM D5X/E5X datasheet, the JTAG/SWD pin-out uses TCK / TMS / TDI / TDO / SWDIO / SWCLK on dedicated pins which must NOT be repurposed for general GPIO without disabling the JTAG fuse.
Информация о соответствии
RoHS compliant per Microchip material declaration. Not AEC-Q100 qualified; for automotive applications use ATSAMD51J19A-AUT (Q-1 grade) on same 64-QFN footprint.
