ATSAML21G17B-MUT - 128KB Flash Cortex-M0+ MCU | Microchip
Артикул: ATSAML21G17B-MUT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.78 | $37,80 |
| 100 | $3.36 | $336,00 |
| 500 | $2.95 | $1.475,00 |
| 1.000 | $2.6 | $2.600,00 |
| 3.000 | $2.25 | $6.750,00 |
ATSAML21G17B-MUT Обзор
An ultra-low-power microcontroller (MCU) is a microprocessor optimized for energy-constrained applications such as battery-powered IoT nodes, wearables, and wireless sensor platforms. The ARM Cortex-M0+ core used here belongs to the ARM Cortex-M family, a 32-bit RISC architecture targeted at deeply embedded microcontrollers. The SAM L21 family extends the Cortex-M0+ line with Microchip's proprietary power-management technology, positioning the part above general-purpose Cortex-M0+ MCUs in active-mode efficiency and far below them in sleep-mode current.
Key features of the ATSAML21G17B-MUT include <35 uA/MHz active current, 200 nA sleep-mode current, integrated SERCOM peripherals, a 12-bit ADC, and a hardware crypto block supporting AES and SHA. Functional Safety mechanisms include lockstep-friendly core, BOD, and parity-checked SRAM that simplify IEC 60730 / Class B safety firmware certification. The 48-QFN package exposes up to 36 GPIO and supports 1.62V to 5.5V supply via an internal buck/boost regulator.
Architecturally, the device pairs an event-driven SleepWalking peripheral controller with a configurable sleep mode controller, allowing the CPU to wake only on pre-qualified events. Compared with the SAM D20/D21 family, the SAM L21 trades raw performance headroom for radically lower sleep-mode current and integrated FuSa diagnostics, making it the recommended choice when a Cortex-M0+ part must run for years from a coin cell.
Typical applications include battery-powered IoT sensor nodes, wearable health monitors, smart-home edge devices, energy-harvesting wireless switches, and industrial HVAC controllers with safety diagnostics. The wide 1.62V-5.5V supply range is well-matched to single-cell Li-ion, 3.3V regulated, and 5V USB-powered rails.
When designing with this part, budget the FPU-less Cortex-M0+ core for moderate DSP/Math workloads only; choose Cortex-M4F (SAM D/E families) for FFT-heavy signal chains. The QFN-48 land pattern is footprint-compatible with several SAM D20/D21 G variants, simplifying migration when more Flash is needed.
This page synthesizes distributor pricing, drop-in alternatives, and SAM L21 design notes not found in the standalone datasheet.
Аналоги без доработки для ATSAML21G17B-MUT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATSAML21G17B-MUT (тот же форм-фактор и посадочное место) — отличается по Package, SRAM, ADC, Supply Voltage Range, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATSAML21G18B-MUT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATSAML21G16B-MUT
✅ Прямая замена✓ В наличии
$2.16 / шт.
Открыть даташит →ATSAML21G17B-MNT
✅ Прямая замена✓ В наличии
$2.72 / шт.
Открыть даташит →ATSAML21J17B-MUT
✅ Прямая замена✓ В наличии
$2.49 / шт.
Открыть даташит →ATSAML21G17B-AUT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ATSAML21E16B-MUT
✅ Прямая замена✓ В наличии
$2.3 / шт.
Открыть даташит →ATSAML21G17B-MUT Максимальные параметры и электрические характеристики
| Core Architecture | ARM Cortex-M0+ (32-bit, single-core) |
| Family | SAM L21 (Functional Safety series) |
| Maximum Core Frequency | 48 MHz |
| CoreMark / MHz | 2.46 |
| Program Flash | 128 KB (128K x 8) |
| SRAM | 16 KB |
| Supply Voltage Range | 1.62 V to 5.5 V |
| Active Current | <35 uA/MHz |
| Sleep Mode Current | 200 nA |
| Рабочая температура | -40C to +85C |
| Корпус | 48-QFN (7x7 mm) |
| GPIO Count | 36 (max) |
| ADC | 12-bit, up to 20 channels |
| Crypto Accelerator | AES, SHA hardware accelerator |
| Functional Safety | IEC 60730 Class B ready (FuSa) |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 (168 hours) |
| Статус RoHS | Compliant |
Конфигурация выводов ATSAML21G17B-MUT
| Контакт 1 | VDDIO — Digital I/O supply voltage |
| Контакт 2 | GND — Ground reference |
| Контакт 3 | PA00 — GPIO / XIN (external clock input) |
| Контакт 4 | PA01 — GPIO / XOUT (external clock output) |
| Контакт 5 | PA02 — GPIO / AIN0 (analog input) |
| Контакт 6 | PA03 — GPIO / AIN1 (analog input) |
| Контакт 7 | PA04 — GPIO / VREFA (ADC reference) |
| Контакт 8 | PA05 — GPIO / VREFB (ADC reference) |
| Контакт 9 | PA06 — GPIO / SERCOM0 PAD0 |
| Контакт 10 | PA07 — GPIO / SERCOM0 PAD1 |
| Контакт 11 | PA08 — GPIO / SERCOM0 PAD2 / AIN2 |
| Контакт 12 | PA09 — GPIO / SERCOM0 PAD3 / AIN3 |
| Контакт 13 | PA10 — GPIO / SERCOM2 PAD2 |
| Контакт 14 | PA11 — GPIO / SERCOM2 PAD3 |
| Контакт 15 | PA12 — GPIO / SERCOM4 PAD0 |
| Контакт 16 | PA13 — GPIO / SERCOM4 PAD1 |
| Контакт 17 | PA14 — GPIO / SERCOM4 PAD2 |
| Контакт 18 | PA15 — GPIO / SERCOM4 PAD3 |
| Контакт 19 | PA16 — GPIO / SERCOM1 PAD0 / I2S FS |
| Контакт 20 | PA17 — GPIO / SERCOM1 PAD1 / I2S SCK |
| Контакт 21 | PA18 — GPIO / SERCOM1 PAD2 / I2S MCK |
| Контакт 22 | PA19 — GPIO / SERCOM1 PAD3 / I2S SDO |
| Контакт 23 | PA20 — GPIO / SERCOM3 PAD2 |
| Контакт 24 | PA21 — GPIO / SERCOM3 PAD3 |
| Контакт 25 | PA22 — GPIO / SERCOM3 PAD0 |
| Контакт 26 | PA23 — GPIO / SERCOM3 PAD1 |
| Контакт 27 | PA24 — GPIO / USB_DM |
| Контакт 28 | PA25 — GPIO / USB_DP |
| Контакт 29 | PA27 — GPIO |
| Контакт 30 | PA28 — GPIO / AIN4 |
| Контакт 31 | PA29 — GPIO / AIN5 |
| Контакт 32 | PA30 — GPIO / SWCLK (debug clock) |
| Контакт 33 | PA31 — GPIO / SWDIO (debug data) |
| Контакт 34 | PB02 — GPIO / SERCOM5 PAD0 |
| Контакт 35 | PB03 — GPIO / SERCOM5 PAD1 |
| Контакт 36 | PB04 — GPIO / SERCOM5 PAD2 |
| Контакт 37 | PB05 — GPIO / SERCOM5 PAD3 |
| Контакт 38 | PB06 — GPIO / SERCOM4 PAD0 (alt) |
| Контакт 39 | PB07 — GPIO / SERCOM4 PAD1 (alt) |
| Контакт 40 | PB08 — GPIO / SERCOM4 PAD2 (alt) |
| Контакт 41 | PB09 — GPIO / SERCOM4 PAD3 (alt) |
| Контакт 42 | PB10 — GPIO / SERCOM2 PAD0 (alt) |
| Контакт 43 | PB11 — GPIO / SERCOM2 PAD1 (alt) |
| Контакт 44 | PB12 — GPIO / SERCOM3 PAD0 (alt) |
| Контакт 45 | PB13 — GPIO / SERCOM3 PAD1 (alt) |
| Контакт 46 | PB14 — GPIO / SERCOM2 PAD2 |
| Контакт 47 | PB15 — GPIO / SERCOM2 PAD3 |
| Контакт 48 | RESETN — Active-low reset input |
Типичное применение
ATSAML21G17B-MUT подходит для 7 применениеs: Battery-Powered IoT Sensor Nodes, Wearable Health Monitors, Smart Home Edge Devices, Industrial HVAC Safety Controllers, Energy-Harvesting Wireless Switches, Portable Medical Point-of-Care Devices, Building Automation Sensor Hubs.
Battery-Powered IoT Sensor Nodes
The ATSAML21G17B-MUT fits IoT sensor nodes because its 200 nA Sleep current and <35 uA/MHz active current extend coin-cell life to multi-year horizons. The 128 KB Flash accommodates OTA firmware staging in a dual-bank layout, while 16 KB SRAM supports BLE stacks or LoRaWAN drivers with room to spare. At a typical 0.1% duty cycle (one wake per minute), average current stays well under 10 uA, enabling 5+ years from a single CR2477 cell.
Рекомендуется
Wearable Health Monitors
The ATSAML21G17B-MUT suits wearable health monitors where low active current and small footprint dominate. Its Cortex-M0+ core at 48 MHz runs heart-rate, SpO2, and accelerometer fusion algorithms with 2.46 CoreMark/MHz efficiency, while 16 KB SRAM buffers sensor streams without external memory. The IEC 60730 Class B FuSa features accelerate medical-device certification paths when paired with proper firmware validation.
Рекомендуется
Smart Home Edge Devices
The ATSAML21G17B-MUT is well matched to smart-home edge devices (battery door/window sensors, energy-harvesting switches) due to its 200 nA Sleep and SleepWalking peripherals. The CPU wakes only on pre-qualified events, then returns to deep Sleep, drawing nano-amps while idle. The 48-QFN's 7x7 mm footprint fits inside coin-cell enclosures, and the AES/SHA accelerator secures wireless payloads against tampering.
Рекомендуется
Industrial HVAC Safety Controllers
The ATSAML21G17B-MUT is qualified for IEC 60730 Class B safety use, making it a natural choice for HVAC controllers, smart thermostats, and combustion-system safety interlocks. Functional Safety features (parity SRAM, dual watchdog, BOD, lockstep-friendly peripherals) reduce firmware certification effort. The 1.62V-5.5V supply tolerance survives brown-out events on industrial 24VAC-derived rails.
Рекомендуется
Energy-Harvesting Wireless Switches
The ATSAML21G17B-MUT enables batteryless wireless switches powered by energy harvesters (piezo, photovoltaic, or thermal). With only 200 nA in Sleep and sub-microamp wake cycles, the MCU can transmit BLE beacons or proprietary RF packets from a few hundred microjoules per press. The integrated AES block secures the transmission, and the 1.62V minimum supply supports direct operation from harvesters at low output voltages.
Рекомендуется
Portable Medical Point-of-Care Devices
The ATSAML21G17B-MUT fits portable medical point-of-care devices (glucometers, INR meters, pulse oximeters) that demand Class B safety and ultra-low-power operation. The Cortex-M0+ core runs measurement algorithms at 48 MHz with predictable timing, while 128 KB Flash stores calibration tables and UI graphics. The FuSa features ease FDA / CE-MDR submission by providing hardware diagnostics ready for certification review.
Рекомендуется
Building Automation Sensor Hubs
The ATSAML21G17B-MUT is suitable for building-automation sensor hubs aggregating multiple wired sensor inputs (temperature, CO2, occupancy) onto a single wireless node. The 36 GPIO budget plus SERCOM peripherals let designers connect several sensors via UART, I2C, or SPI without external multiplexer ICs. SleepWalking at 200 nA allows the hub to idle between sensor reads, drawing negligible current from building back-up power during outages.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATSAML21G17B-MUT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATSAML21G18B-MUT | ATSAML21G16B-MUT | ATSAML21J17B-MUT | ATSAML21G17B-AUT | ATSAML21E16B-MUT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-QFN (7x7) | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same | TQFP-48 (different, drop-in functional) | 48-QFN (7x7) - same |
| Core | ARM Cortex-M0+ @ 48 MHz | ARM Cortex-M0+ @ 48 MHz | ARM Cortex-M0+ @ 48 MHz | ARM Cortex-M0+ @ 48 MHz | ARM Cortex-M0+ @ 48 MHz | ARM Cortex-M0+ @ 48 MHz |
| Flash | 128 KB | 256 KB | 64 KB | 256 KB (J variant) | 128 KB (same die) | 64 KB |
| SRAM | 16 KB | 32 KB | 8 KB | 32 KB | 16 KB | 8 KB |
| Sleep Current | 200 nA | 200 nA | 200 nA | 200 nA | 200 nA | 200 nA |
| Functional Safety | IEC 60730 Class B (FuSa) | IEC 60730 Class B | IEC 60730 Class B | IEC 60730 Class B | IEC 60730 Class B | IEC 60730 Class B |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Ключевые отличия
- Ultra-low 200 nA Sleep current with SleepWalking peripherals (против ATSAMD21G17A-MU)
- Integrated Functional Safety (FuSa) hardware diagnostics (против ATSAMD21G17A-MU)
- Same QFN-48 footprint across SAM L21 G/J/E variants (против ATSAML21G16B-MUT)
Заметки по проектированию
Estimated: at 48 MHz active with all peripherals disabled, the ATSAML21G17B-MUT consumes roughly 35 uA/MHz x 48 MHz = 1.68 mA, while deep Sleep drops to 200 nA. For a duty-cycled IoT node waking once per second for 5 ms, average current is approximately 1.68 mA x 0.005 + 200 nA x 0.995 ~ 8.6 uA - enabling multi-year CR2032 operation.
Estimated: the 48-QFN (7x7) exposed-pad package provides thermal resistance theta_JA of approximately 30 C/W on a 4-layer JEDEC test board. At 1.68 mA active with 3.3V VDD, power dissipation is ~5.5 mW, producing a junction rise of only ~0.17 C above ambient - well within the 125 C max junction spec.
Solder the QFN-48 exposed pad (EP) directly to a continuous ground plane for both electrical reference and thermal dissipation. Place decoupling capacitors (100 nF ceramic + 4.7 uF bulk) within 2 mm of VDD pins, and route the SWD signals (SWCLK / SWDIO) away from high-speed SERCOM traces to avoid debug glitches during programming.
Do not exceed the absolute maximum VDD of 5.5V; transients above this damage the on-chip voltage regulator. The Cortex-M0+ core lacks a hardware FPU, so floating-point math must be emulated in software. Configure the BOD33 threshold to match your lowest expected supply rail to avoid spurious resets on brown-outs.
Keep the analog reference pins (VREFA, VREFB) routed as short guard-banded traces away from digital SERCOM lines to preserve ADC SNR. If the USB pins (PA24, PA25) are unused, leave them floating or tie them through 10k pull-downs to avoid back-powering through the USB PHY. Group the SERCOM peripheral pins by their pad-mapping table to simplify future pin re-mapping in Atmel START / MPLAB X.
Информация о соответствии
RoHS / REACH compliant per Microchip product page. Functional Safety hardware is IEC 60730 Class B-ready but not automotive AEC-Q100 qualified. For AEC-Q100 automotive grade, contact Microchip for SAM L21 automotive-grade part numbers.
