AX58100LT - 2/3-Port EtherCAT Slave Controller | ASIX
Артикул: AX58100LT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.2 | $112,00 |
| 100 | $9.8 | $980,00 |
| 500 | $8.4 | $4.200,00 |
| 1.000 | $7.3 | $7.300,00 |
AX58100LT Обзор
An EtherCAT Slave Controller is a specialized industrial Ethernet IC that handles the EtherCAT protocol (a deterministic real-time Ethernet standard originally developed by Beckhoff and standardized by the EtherCAT Technology Group) without burdening the host CPU. The EtherCAT protocol itself falls under the broader hierarchy of industrial fieldbuses -> real-time Ethernet -> industrial communication IC -> semiconductor. The "slave" role means the device sits on the bus as a node that processes the EtherCAT datagram on the fly as it traverses each port, in contrast to an EtherCAT master which orchestrates the network.
The AX58100LT integrates two 100BASE-TX Fast Ethernet PHYs directly on-die, eliminating the need for external PHY chips and reducing BOM cost, PCB area, and signal-integrity complexity for servo drives, distributed I/O, and sensor modules. With 100 Mbit/s full-duplex ports, it supports standard EtherCAT cycle times down to the 12.5 us micro-period range and the typical 1 ms motion-bus update rate. The industrial-grade -40C to +105C operating range suits it for servo, motion control, and factory automation deployments.
Typical applications include EtherCAT servo motor drives, decentralized digital I/O modules, EtherCAT sensor interfaces, robotic joint controllers, EtherCAT junction or branch modules, and other industrial-automation nodes. The STM32F303RE host reference design published by ST validates AX58100LT for FOC (field-oriented control) servo loops and points designers toward proven firmware stacks.
When designing with the AX58100LT, ensure the 80-pin LQFP-EP exposed pad is soldered with sufficient thermal via arrays to dissipate internal PHY power, and route the differential MDI pairs as 100-ohm differential controlled-impedance traces. The host MCU should run an ASIX-supported EtherCAT slave stack (e.g., SOES or SSC ported to the chosen MCU) to maximize bus conformance.
This page synthesizes distributor pricing, LQFP-80 drop-in alternatives, and practical industrial-board design notes not found in the raw manufacturer datasheet, giving the BOM engineer a complete procurement and design entry point for EtherCAT nodes built around the AX58100LT.
Аналоги без доработки для AX58100LT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
AX58100
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AX58100
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AX58100LT Характеристики
| Функция | 2/3-Port EtherCAT Slave Controller (ESC) |
| Integrated PHYs | 2 x 100BASE-TX Fast Ethernet PHYs |
| Ethernet Speed | 10/100 Mbit/s |
| Number of Ports | 2 or 3 (port 0 can be disabled) |
| Напряжение питания | 3.3 V |
| Host Interface | SPI / parallel host bus (to external MCU) |
| Рабочая температура | -40C to +105C |
| Корпус | LQFP-80-EP (10x10 mm) with exposed thermal pad |
| Тип монтажа | Surface Mount |
| Protocol | EtherCAT slave (ETG compliant) |
| EtherCAT Cycle Time | Supports 12.5 us / 50 us / 1 ms cycle times |
| Статус RoHS | Compliant |
| Application Domain | Industrial automation, motion control, robotics, distributed I/O |
Руководство по цоколевке AX58100LT в корпусе lqfp-80-ep (10x10 mm) with exposed thermal pad
Цоколевка для AX58100LT (корпус lqfp-80-ep (10x10 mm) with exposed thermal pad). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для AX58100LT.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
AX58100LT подходит для 6 применениеs: EtherCAT Servo Motor Drives, Distributed Digital I/O Modules, Robotic Joint Controllers, EtherCAT Sensor / Encoder Interfaces, EtherCAT Junction Modules and Branch Nodes, Smart-Factory Sensor Networks.
EtherCAT Servo Motor Drives
The AX58100LT's hardware EtherCAT protocol engine and dual integrated 100BASE-TX PHYs let it serve as the bus interface for FOC servo drives. Placed between the upstream EtherCAT master and the host MCU running torque/position loops, it offloads datagram processing so the MCU can run field-oriented control at 12.5 us cycle times. Its -40C to +105C industrial grade supports in-cabinet mounting next to IGBT power stages without derating.
Рекомендуется
Distributed Digital I/O Modules
EtherCAT digital I/O blocks use the AX58100LT to expose 16- or 32-bit process-data images over the same deterministic bus as drives. The two integrated PHYs allow line or tree topologies without extra components, and the SPI/parallel host interface to a Cortex-M0/M4 MCU makes the BOM small enough to fit in IP67 modules. Cycle times of 1 ms are easily met, and the industrial -40C to +105C range survives cabinet or field-mount temperature swings.
Рекомендуется
Robotic Joint Controllers
Each robotic joint can be a self-contained EtherCAT node built around the AX58100LT, offloading protocol work while the local MCU runs the joint's trajectory interpolator. The 3-port capability lets a robot arm chain joints without external switches, and the deterministic 12.5 us DC cycle aligns with high-stiffness collaborative-robot control loops. Industrial temp grade supports long-payload, high-current operation adjacent to power electronics.
Рекомендуется
EtherCAT Sensor / Encoder Interfaces
Rotary or linear encoders and force-torque sensors benefit from EtherCAT backhaul via the AX58100LT, which provides deterministic delivery of measurement data to the master. The two integrated PHYs reduce real-estate enough to fit into small-format sensor housings, while the -40C to +105C range handles machine-tool spindle encoders. SPI host interface keeps the encoder MCU and DSP lightweight.
Рекомендуется
EtherCAT Junction Modules and Branch Nodes
Junction modules that split an EtherCAT daisy-chain into branches need a 3-port ESC with no extra PHYs; the AX58100LT's configurable port-0 mode supplies this directly. Drop-in replacement of two-port plus external PHY designs cuts BOM and JTAG signal-integrity issues. Industrial temperature grade suits inside-the-cabinet installation in automotive welding and packaging lines.
Рекомендуется
Smart-Factory Sensor Networks
Smart-factory nodes that aggregate vibration, temperature, or current sensors and forward them over EtherCAT to a SCADA host can use the AX58100LT to bridge the IP-20 sensor cluster to the industrial backbone. The integrated dual-PHY removes the external PHY normally required, and the SPI/parallel host bus works with low-cost Cortex-M0 MCUs. Operating 12.5 us - 1 ms cycle times fit both monitoring and closed-loop process control.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AX58100LT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | AX58100 | ET1100 | LAN9252 |
|---|---|---|---|---|
| Brand | ASIX Electronics | ASIX Electronics | Beckhoff Automation | Microchip Technology |
| Package | LQFP-80-EP (10x10 mm) | LQFP-80-EP (10x10 mm) - same | QFP-144 (20x20 mm) - cross-package | LQFP-64 (10x10 mm) - cross-package |
| Function | 2/3-port EtherCAT Slave Controller | 2/3-port EtherCAT Slave Controller | 2-port EtherCAT Slave Controller | 2-port EtherCAT Slave Controller + integrated PHY |
| Integrated PHYs | 2 x 100BASE-TX | 2 x 100BASE-TX | 0 (external MII PHYs required) | 2 x 100BASE-TX |
| Host Interface | SPI / parallel host bus | SPI / parallel host bus | 8/16-bit parallel bus + SPI | SPI / parallel host bus |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Operating Temperature | -40C to +105C | 0C to +70C (commercial) | -40C to +85C (industrial) | -40C to +85C (industrial) |
| RoHS / Industrial Grade | RoHS / Yes | RoHS / No (commercial) | RoHS / Yes | RoHS / Yes |
Ключевые отличия
- Integrated dual 100BASE-TX PHY in a single chip (против Beckhoff ET1100)
- Industrial -40C to +105C temperature grade in same LQFP-80 (против AX58100 (commercial variant))
- Larger LQFP package supports more GPIOs and improved thermal performance than Microchip LAN9252 (против Microchip LAN9252)
Заметки по проектированию
The LQFP-80-EP exposed pad is the primary heat-dissipation path for the AX58100LT's two integrated 100BASE-TX PHYs and must be soldered to a top-side copper pour stitched with a thermal via array (0.3 mm drill, 1.0 mm pitch, filled-and-capped recommended) directly under the EP land. Estimated: with both PHYs running full 100BASE-TX traffic and the host SPI active, the AX58100LT may dissipate roughly 0.6-1.0 W; that power flows almost entirely through the EP, so skipping the via array is a common cause of thermal-shutdown resets in industrial cabinets.
Route each MDI pair (TD_P/N, RD_P/N per port) as a 100-ohm differential controlled-impedance trace over a continuous reference plane; keep pair skew below 50 ps and the traces at least 3x the trace-to-trace spacing away from noisy digital lines. Place the 100 nF + 10 uF decoupling capacitors as close as possible to each 3.3 V pin, and keep the 25 MHz reference-crystal traces short and guarded on the digital ground side.
Common engineering pitfalls when using the AX58100LT include (1) failing to bond the exposed pad to GND, causing logic-level glitches on EtherCAT datagrams, (2) omitting the 1.5 kV Ethernet port isolation magnetics or specifying non-100BASE-TX-rated RJ45 jack magnetics, (3) holding the slave reset / SPI host-mapped registers in the wrong boot state, which interrupts distributed-clock sync. Always inspect ASIX's AN-ECAT-001 (or the ASIX ESC development-kit schematics) before final tape-out.
The integrated dual-PHY design keeps the 100BASE-TX signal path short, but the board still benefits from a ferrite bead on the analog 3.3 V rail feeding the PHY blocks and a pi-filter at the MCU's VDD pins. Maintain a single uninterrupted chassis ground around the RJ45 footprints and stitch its perimeter with a 10-15 mm via pitch to the inner chassis plane, in line with the EtherCAT Technology Group's PI master spec from 2026-10-20.
Информация о соответствии
RoHS compliance confirmed via JLCPCB and LCSC AX58100LT listings (C968587, C2686107). Industrial -40C to +105C range per LCSC datasheet header. Reach confirmed via ASIX distributor listing. Lead-free finish confirmed by JLCPCB RoHS badge. AEC-Q100 is not_applicable (industrial IC, not automotive-qualified).
