BQ40Z80RSMR - 2-6S Li-Ion Battery Pack Manager | Texas Instruments
Артикул: BQ40Z80RSMR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.45 | $6,45 |
| 10 | $5.78 | $57,80 |
| 100 | $5.12 | $512,00 |
| 500 | $4.62 | $2.310,00 |
| 1.000 | $4.1 | $4.100,00 |
| 3.000 | $3.65 | $10.950,00 |
BQ40Z80RSMR Обзор
A battery pack manager is the heart of a smart battery; it measures individual cell voltages, pack current, and temperature, then derives remaining capacity and state-of-health while enforcing protection limits. The BQ40Z80 belongs to the category hierarchy battery management IC > gas gauge + protector > battery pack manager > power management IC, complementing the charger and protection MOSFETs in the system. Impedance Track is TI's patented coulomb-counting-plus-modeling approach that learns cell impedance at every cycle to deliver accurate runtime prediction even under varying loads and aging.
Key features include 2S to 6S cell support, integrated CC-CV charge profile control via SMBus, hardware secondary protection, 18-bit integrated delta-sigma A/D for cell voltage measurement, on-chip cell balancing drivers, SHA-1/ECC authentication with secure memory, and eight multifunction pins configurable as thermal inputs, GPIO, LEDs, or display-button. Integrated sense resistors and a high-side N-FET drive architecture simplify protection MOSFET selection.
The device communicates over SMBus v1.1 with optional 400 kHz I²C compatibility and offers an LED display driver for 4- or 5-segment SOC indication. On-chip non-volatile memory stores chemistry profiles, learned parameters, and a 64-bit pack ID for traceability. The 4x4 mm QFN footprint enables compact pack designs while providing a thermal pad for heat spreading during high-discharge balancing.
Typical applications include cordless power tool packs, robotic vacuum cleaners, e-bike and e-scooter battery packs, medical infusion pumps, and hot-swap server backup modules. The wide 4.5 V to 32 V operating range tolerates the inductive transients common in motor-driven systems. Designers select the BQ40Z80 when an integrated gauge+protector+authenticator saves PCB area versus discrete solutions like separate AFE plus MCU.
When designing, observe the SMBus address selection pin to avoid collisions with a system charger, and follow the cell-balancing resistor sizing in the datasheet to keep balance current within thermal limits. Pair this gauge with TI's BQ25620 charger IC for a complete pack+system solution.
This page synthesizes distributor pricing, drop-in alternatives within the same 32-VQFN package, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для BQ40Z80RSMR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с BQ40Z80RSMR (тот же форм-фактор и посадочное место) — отличается по Authentication, Cell Balancing, Communication Interface, Gas Gauging Algorithm, Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
BQ40Z80RSMT
✅ Прямая замена✓ В наличии
$5.45 / шт.
Открыть даташит →BQ40Z80RSMR
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.65 / шт.
Открыть даташит →BQ40Z60RHBR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
BQ40Z50RSMR-R2
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
BQ4050RSMR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
BQ40Z80RSMR Характеристики
| Battery Type Supported | Li-Ion / Li-Polymer |
| Number of Cells Supported | 2S to 6S (up to 6 series cells) |
| Рабочее напряжение питания | 4.5 V to 32 V |
| Battery Pack Voltage | Up to 25.2 V (6S Li-Ion) |
| Communication Interface | SMBus v1.1 (I²C-compatible, 100/400 kHz) |
| Gas Gauging Algorithm | Impedance Track™ (TI proprietary) |
| Authentication | SHA-1 / ECC with secure memory |
| Cell Balancing | Internal FET drivers (external N-FETs) |
| Protection Features | OV, UV, OC, SC, OT, charge timeout, watchdog |
| Charge Control | SMBus-controlled CC/CV profile |
| Multifunction Pins | 8 pins (thermal, GPIO, LED, button input) |
| Рабочая температура | -40 °C to +85 °C |
| Корпус | 32-VQFN (RSM) 4x4 mm |
| Тип монтажа | Surface Mount |
| Уровень MSL | 2 (1 year) |
| Статус RoHS | Compliant |
| LED Display Driver | 4- or 5-segment SOC indicator |
Конфигурация выводов BQ40Z80RSMR
| Контакт 1 | VC1 — Cell 1 voltage sense (positive) |
| Контакт 2 | VC2 — Cell 2 voltage sense (positive) |
| Контакт 3 | VC3 — Cell 3 voltage sense (positive) |
| Контакт 4 | VC4 — Cell 4 voltage sense (positive) |
| Контакт 5 | VC5 — Cell 5 voltage sense (positive) |
| Контакт 6 | VC6 — Cell 6 voltage sense (positive) |
| Контакт 7 | BAT — Battery pack voltage sense (top of stack) |
| Контакт 8 | SRP — Current sense positive input |
| Контакт 9 | SRN — Current sense negative input |
| Контакт 10 | GND — Analog ground |
| Контакт 11 | P1 — Multifunction pin 1 (thermal/GPIO/LED/button) |
| Контакт 12 | P2 — Multifunction pin 2 |
| Контакт 13 | P3 — Multifunction pin 3 |
| Контакт 14 | P4 — Multifunction pin 4 |
| Контакт 15 | P5 — Multifunction pin 5 |
| Контакт 16 | P6 — Multifunction pin 6 |
| Контакт 17 | P7 — Multifunction pin 7 |
| Контакт 18 | P8 — Multifunction pin 8 |
| Контакт 19 | SDA — SMBus data |
| Контакт 20 | SCL — SMBus clock |
| Контакт 21 | PRES — Pack presence pin |
| Контакт 22 | ALERT — SMBus alert output |
| Контакт 23 | DISP — Display button input |
| Контакт 24 | CHG — Charge FET gate drive |
| Контакт 25 | DSG — Discharge FET gate drive |
| Контакт 26 | PACK+ — Pack positive terminal sense |
| Контакт 27 | FUSE — Fuse blow output |
| Контакт 28 | TS1 — Thermal sense input 1 |
| Контакт 29 | TS2 — Thermal sense input 2 |
| Контакт 30 | TS3 — Thermal sense input 3 |
| Контакт 31 | VCC — Internal supply (decouple) |
| Контакт 32 | EP — Exposed thermal pad (ground) |
Типичное применение
BQ40Z80RSMR подходит для 6 применениеs: Cordless Power Tool Battery Packs, E-Bike and E-Scooter Battery Packs, Medical Infusion Pumps and Carts, Industrial UPS and Battery Backup Modules, Robotic Vacuum Cleaner Battery Packs, Portable Solar Power Stations.
Cordless Power Tool Battery Packs
The BQ40Z80RSMR is engineered for 18 V (5S) and 36 V (10S) cordless power tool packs that demand precise state-of-charge reporting and rugged protection. Its 32 V operating ceiling tolerates inductive kickback from brushed and brushless motors, while integrated SHA-1/ECC authentication blocks counterfeit cell replacement. Place the gauge on the pack PCM with high-side N-FETs, balancing resistors sized for 100-200 mA per cell, and an SMBus link to the tool's motor controller for runtime prediction. Unlike discrete AFE+MCU solutions, the BQ40Z80 consolidates gauge, protection, balancing, and auth in one chip.
Рекомендуется
E-Bike and E-Scooter Battery Packs
For 24 V (7S) to 48 V (13S) e-mobility battery packs, the BQ40Z80RSMR delivers the voltage headroom, accurate Impedance Track™ gauging, and SMBus interface needed for pedal-assist and throttle control. The wide 4.5-32 V operating range and 85 °C thermal limit handle sustained motor currents and pack heating, while integrated balancing extends runtime across cell groups. The eight multifunction pins can drive an LED SOC indicator on the pack housing, and the 32-VQFN footprint fits inside slim down-tube enclosures. Pair with a BQ25620 charger and CAN-translator MCU to surface pack data to the e-bike dashboard.
Рекомендуется
Medical Infusion Pumps and Carts
Medical infusion pumps and mobile workstation carts require reliable runtime prediction for IEC 60601-1 patient-safety compliance. The BQ40Z80RSMR's accurate Impedance Track™ algorithm provides clinically meaningful SOC percentage and time-to-empty figures, and its hardware protections (OV/UV/OC/OT) satisfy fault-tolerant design expectations. The 32-VQFN 4x4 mm footprint fits compact pack assemblies where space is at a premium, and the wide operating temperature range supports hospital, ambulance, and home-health environments. Use the SHA-1 authentication to ensure only OEM-approved cells can be installed in service-replaceable packs.
Рекомендуется
Industrial UPS and Battery Backup Modules
Industrial UPS racks and telecom backup batteries using 6S Li-Ion configurations benefit from the BQ40Z80RSMR's integrated protection and SMBus telemetry to the rack controller. The gauge reports SOC, time-to-empty, and cell-level health, allowing predictive replacement cycles and reducing truck-roll cost. Hardware OV/UV/OC protections disconnect the pack during faults, while on-chip ECC authentication prevents service bypass. Industrial EMC immunity is supported by the VQFN-32 ground pad layout that provides low-impedance return for the SMBus clock and data lines.
Рекомендуется
Robotic Vacuum Cleaner Battery Packs
Robotic vacuum cleaners use 4S Li-Ion packs that need compact, accurate gauging in a 4x4 mm VQFN footprint. The BQ40Z80RSMR provides precise SOC reporting to the robot's main MCU over SMBus, and the eight multifunction pins drive 4- or 5-segment LED indicators on the dock or robot body. Integrated cell balancing extends pack cycle life across repeated charge/discharge cycles typical of daily cleaning duty. Pair with a TI wireless charger and BMS-friendly charging profile.
Рекомендуется
Portable Solar Power Stations
Portable power stations with 6S Li-Ion packs benefit from the BQ40Z80RSMR's wide 32 V operating ceiling, accurate gauging across variable solar charge currents, and integrated balancing for cells that see uneven aging from partial state-of-charge operation. The gauge communicates pack SOC and fault conditions over SMBus to the inverter's host MCU, while the SHA-1/ECC authentication prevents unauthorized cell-pack retrofits in field-deployed stations. Use external balancing resistors sized for the high-charge currents typical of MPPT solar input.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для BQ40Z80RSMR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | BQ40Z80RSMT | BQ40Z60RHBR | BQ40Z50RSMR-R2 | BQ4050RSMR | LTC6813IWE |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 32-VQFN (RSM) 4x4 mm | 32-VQFN (RSM) 4x4 mm - same | 32-VQFN (RHB) - same VQFN-32 family | 32-VQFN (RSM) 4x4 mm - same | 32-VQFN (RSM) 4x4 mm - same | 48-LQFP - different package |
| Cell Support | 2S to 6S Li-Ion/Li-Poly | 2S to 6S | 2S to 6S | 1S to 4S | 1S to 4S | 6S to 18S |
| Authentication | SHA-1 / ECC | SHA-1 / ECC | SHA-1 only | SHA-1 only | None | None |
| Operating Voltage | 4.5 V to 32 V | 4.5 V to 32 V | 4.5 V to 32 V | 4.5 V to 20 V | 4.5 V to 20 V | 4.5 V to 60 V |
| Communication Interface | SMBus v1.1 (I²C) | SMBus v1.1 | SMBus v1.1 | SMBus v1.1 | SMBus v1.1 | SPI (host-MCU managed) |
| Internal Balancing Drivers | Yes (external N-FETs) | Yes | Yes | Yes | Yes | No - external MCU controlled |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
| Approx. Unit Price (qty 1) | USD 6.45 | USD 6.45 | USD 5.95 | USD 5.40 | USD 4.85 | USD 8.20 |
Ключевые отличия
- ECC authentication with secure memory for anti-counterfeit protection (против BQ40Z60RHBR)
- Higher cell count support up to 6S without external balancing hardware (против BQ40Z50RSMR-R2)
- Integrated SMBus-controlled CC/CV charge profile (против LTC6813IWE)
- Eight multifunction pins configurable as thermal, GPIO, LED, or display button (против BQ4050RSMR)
Заметки по проектированию
Provide a low-impedance BAT pin connection to the top of the cell stack with a 1 µF X7R bypass close to the IC, and a 100 nF in parallel for high-frequency noise. The BQ40Z80 internally regulates VCC from BAT; keep cell voltage traces short to avoid ripple coupling into the analog front-end. For 6S packs with significant load transients, add a 10 µF bulk cap on BAT to stabilize the internal LDO during heavy discharge pulses.
The 32-VQFN exposed thermal pad (pin 32) MUST be soldered to a copper pour connected to analog ground to provide thermal dissipation and a low-impedance return. Allocate at least 25 mm² of 1 oz copper on the top layer tied to AGND for heat spreading during sustained cell balancing. Differential routing of SRP/SRN (sense resistor traces) with matched length and 50 Ω impedance improves coulomb-counting accuracy in high-discharge power-tool packs.
Do not exceed 32 V on the BAT pin - hot-plug and motor kickback can exceed this. Place TVS protection (e.g., SMBJ33CA) on the pack input if inductive transients are expected. The SMBus SDA/SCL pins require external pull-ups (typ. 10 kΩ to a clean 3.3 V supply) - missing pull-ups are a common board bring-up failure. Ensure the PRES pin is correctly bonded to indicate pack insertion per TI's reference designs.
Estimated: at 6S, 30 V VIN and 100 mA continuous balancing per cell, the BQ40Z80 dissipates approximately 0.3 W via the exposed pad. With a 4-layer PCB and 1 oz copper on top, theta_JA is approximately 35 °C/W, giving a 10 °C junction rise. For industrial 70 °C ambient operation, this leaves comfortable thermal margin. In enclosed packs without airflow, derate balancing current to 50 mA per cell to limit self-heating.
Информация о соответствии
RoHS and REACH compliant per TI product page. Lead-free and halogen-free reflow compatible. For AEC-Q100 automotive qualified version, order BQ40Z80RSMR with Q1 suffix; standard RSMR is industrial/commercial grade.
