BTS5030-1EJA - 30mΩ Smart High-Side Switch | Infineon PROFET+ 12V
Артикул: BTS5030-1EJA ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.85 | $2,85 |
| 10 | $2.55 | $25,50 |
| 100 | $2.18 | $218,00 |
| 500 | $1.86 | $930,00 |
| 1.000 | $1.59 | $1.590,00 |
BTS5030-1EJA Обзор
A high-side power switch (also called a smart high-side switch or PROFET) is a semiconductor relay that sits between the battery/load supply and the load, replacing an electromechanical relay or a discrete low-side MOSFET plus fuse combination. Compared with a low-side switch it provides inherent load-short-to-ground protection and simpler wiring, and compared with a mechanical relay it offers silent operation, fast diagnostics, and programmable current limiting. Within automotive power-tree taxonomy, the BTS5030-1EJA belongs to the family: smart high-side switch → protected MOSFET driver → power distribution IC → power management IC.
Key features include a 30 mΩ typ. ON-state resistance at 25 °C, integrated protection functions (current limiting, overtemperature shutdown, overvoltage clamp including load-dump, short-to-ground and short-to-battery detection), and proportional load-current sensing via the IS pin. The device operates from a logic-level IN input (3.3 V / 5 V CMOS-compatible) and provides a DEN diagnostic feedback pin that distinguishes normal operation, open load, overtemperature, and short-circuit conditions. The exposed thermal pad keeps junction-to-ambient thermal resistance low enough to sustain multi-ampere loads without an external heatsink in PCB-typical layouts.
Typical applications include automotive exterior and interior lighting (H7 headlamps, DRL, fog lamps, turn indicators), resistive and inductive loads (seat heaters, mirror heaters, solenoid valves), and general 12 V power distribution in body-control modules. Diagnostic feedback enables ECU-level fault detection without additional wiring or shunt resistors. When designing with the BTS5030-1EJA, observe the printed-circuit layout guidelines in the Infineon application note for PROFET+ 12V devices, keep the exposed pad soldered to a continuous ground copper pour for thermal performance, and respect the maximum energy rating during demagnetization of inductive loads.
Аналоги без доработки для BTS5030-1EJA — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с BTS5030-1EJA (тот же форм-фактор и посадочное место) — отличается по Package, Diagnostic Output, Product Type, RoHS Status, Automotive Qualification.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
BTS50301EJAXUMA1
✅ Прямая замена✓ В наличии
$1.82 / шт.
Открыть даташит →ITS4100SSJNXUMA1
✅ Прямая замена✓ В наличии
$0.89 / шт.
Открыть даташит →BTS4175SGAXUMA1
✅ Прямая замена✓ В наличии
$0.71 / шт.
Открыть даташит →NCV8460ADR2G
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISP772T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
BTS5030-1EJA Максимальные параметры и электрические характеристики
| Product Family | PROFET™ + 12V |
| Функция | Single-channel Smart High-Side Power Switch |
| On-State Resistance (RDS(on) typ.) | 30 mΩ |
| Nominal Load Current | 36 A |
| Operating Voltage Range (VS) | 5 V to 28 V |
| Load Dump Clamp Voltage | 41 V (typ.) |
| Logic Input Voltage (IN, DEN) | 3.3 V / 5 V CMOS compatible |
| Diagnostic Output | Current sense (IS) + digital fault pin (DEN) |
| Protection Functions | Current limit, overtemperature shutdown, overvoltage clamp, short-to-ground, short-to-Vbat |
| Output Stage Technology | N-channel vertical power MOSFET with charge pump |
| Корпус | PG-DSO-8-43 EP (Exposed Pad) |
| Тип монтажа | Surface Mount |
| Operating Temperature (junction) | -40 °C to +150 °C |
| Уровень MSL | 3 |
| Статус RoHS | Compliant |
| Automotive Qualification | AEC-Q100 qualified (PROFET+ automotive grade) |
Конфигурация выводов BTS5030-1EJA
| Контакт 1 | OUT — Drain output to load (electrically tied to exposed pad) |
| Контакт 2 | NC — Not connected (per datasheet) |
| Контакт 3 | VS — Battery supply input (12 V / 24 V) |
| Контакт 4 | VS — Battery supply input (parallel pin for lower impedance) |
| Контакт 5 | IN — Logic-level input (3.3 V / 5 V CMOS), enables output stage |
| Контакт 6 | DEN — Diagnostic enable / fault flag (open-drain) |
| Контакт 7 | GND — Logic and analog ground reference |
| Контакт 8 | IS — Proportional load-current sense output (analog) |
Типичное применение
BTS5030-1EJA подходит для 6 применениеs: Automotive Headlamp Load Driver, Daytime Running Light (DRL) LED Driver, Seat Heater / Mirror Heater Power Stage, Solenoid Valve Driver (12 V Automotive), Body Control Module (BCM) Power Distribution, Industrial 24 V Resistive Load Switching.
Automotive Headlamp Load Driver
The BTS5030-1EJA's 30 mΩ RDS(on) and 36 A nominal continuous rating make it a strong fit for direct-driving H7 / H4 halogen headlamp bulbs from a 12 V battery rail. With the bulb drawing typically 5 A per filament, conduction loss is only 0.75 W per channel, keeping the junction temperature rise manageable on a 1 oz copper SO-8 EP thermal pad. The integrated short-to-ground and load-dump protection satisfies ISO 7637-2 transient requirements without external TVS diodes, and the DEN pin feeds a fault flag directly back to the BCM ECU.
Рекомендуется
Daytime Running Light (DRL) LED Driver
Driving DRL LED strings from the BTS5030-1EJA benefits from its analog IS current-sense pin, which produces a proportional load-current image the BCM can use for LED-open detection. The part's 5 V to 28 V operating window covers cold-crank and jump-start conditions without nuisance tripping, and the integrated overtemperature auto-restart prevents thermal runaway when the LED harness develops a partial short. Designers typically add a 1 kHz PWM on the IN pin for DRL dimming, which the BTS5030-1EJA supports up to its switching-time limits.
Рекомендуется
Seat Heater / Mirror Heater Power Stage
Resistive heating loads such as seat heaters (~10 A) and mirror heaters (~3 A) sit comfortably within the BTS5030-1EJA's 36 A envelope, with the SO-8 EP exposed pad providing the thermal headroom required for continuous PWM operation. The device's short-to-Vbat protection prevents back-feeding when a heater element chafes against chassis ground, a common automotive failure mode. Current sense via the IS pin enables closed-loop heater temperature regulation in firmware on the BCM.
Рекомендуется
Solenoid Valve Driver (12 V Automotive)
Inductive loads such as solenoid valves for transmission, emissions, or HVAC systems require a free-wheeling path when switched off. The BTS5030-1EJA's internal clamp handles the demagnetization energy for moderate solenoids without external TVS, simplifying the PCB. The DEN pin distinguishes between stuck-open and stuck-closed faults, which is critical for OBD-II diagnostics on emission-related solenoids. Verify the inductive load energy against the datasheet EAS rating to confirm safe operation.
Рекомендуется
Body Control Module (BCM) Power Distribution
Each BTS5030-1EJA can replace a discrete MOSFET-plus-fuse combination in a BCM, freeing board space and providing digital diagnostics that discrete solutions cannot. Stacking multiple BTS5030-1EJA channels gives the BCM programmable current-limit per output (via MCU-driven IN duty cycle), enabling zonal architectures where each load is software-configurable. The PROFET+12V family's reputation for field reliability makes it a first-choice building block for new BCM designs targeting ASIL-B functional safety.
Рекомендуется
Industrial 24 V Resistive Load Switching
Although optimized for 12 V automotive, the BTS5030-1EJA can switch 24 V industrial loads (relays, small heaters, indicator lamps) up to its 28 V maximum supply rating. The exposed-pad SO-8 EP footprint enables hand-soldered prototype boards, and the wide logic-level input range works with 3.3 V microcontrollers common in industrial PLCs. For higher-voltage industrial buses (48 V and above) choose a PROFET+24V or PROFET+48V family member instead.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для BTS5030-1EJA — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | BTS50301EJAXUMA1 | ITS4100SSJNXUMA1 | BTS4175SGA | NCV8460ADR2G | ISP772T |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies (same die) | Infineon Technologies | Infineon Technologies | onsemi | Infineon Technologies |
| Package | PG-DSO-8-43 EP (Exposed Pad) | PG-DSO-8-43 EP - same | PG-DSO-8-43 EP - same | PG-DSO-8-43 EP - same | PG-DSO-8-43 EP - same | PG-DSO-8-43 EP - same |
| On-State Resistance (RDS(on) typ.) | 30 mΩ | 30 mΩ | ~200 mΩ (higher) | ~175 mΩ | ~50 mΩ | ~50 mΩ |
| Nominal Continuous Current | 36 A | 36 A | ~1.4 A | ~1.8 A | ~6 A | ~4.5 A |
| Operating Voltage Range (VS) | 5 V to 28 V | 5 V to 28 V | 5 V to 28 V | 5 V to 28 V | 5 V to 28 V | 5 V to 28 V |
| Current Sense Output | Yes (IS pin, analog proportional) | Yes (IS pin) | Yes (IS pin) | Yes (IS pin) | Yes (CS pin) | Yes (IS pin) |
| AEC-Q100 Automotive Qualified | Yes | Yes | Yes | Yes | Yes | Yes |
Ключевые отличия
- Lowest RDS(on) in the cited PROFET SO-8 EP cross-reference set (против ITS4100SSJNXUMA1)
- Highest continuous current rating in the cross-reference set (против BTS4175SGA)
- True drop-in replacement for the BTS5030-1EJA bare part (против NCV8460ADR2G (onsemi))
Заметки по проектированию
The PG-DSO-8-43 EP exposed pad is the primary thermal path. Solder it to a continuous copper pour that spans at least 1 cm² of 1 oz copper on the top layer, with thermal vias to the inner/outer ground planes. Estimated: at 30 mΩ RDS(on) and 10 A continuous load, conduction loss is I²R = 100 × 0.030 = 3 W, which on a well-poured PCB keeps the junction rise well below 50 K. Without the thermal pad soldered, expect the device to thermal-limit at much lower currents.
Keep VS pins 3 and 4 connected together on the PCB with a wide, short trace (or polygon) directly to the battery feed input capacitor. Place a 100 nF ceramic + 10 µF electrolytic bulk cap within 5 mm of the VS pins to absorb the reverse-recovery energy of the body diode during inductive load turn-off. The exposed pad should be tied to OUT (pin 1) for thermal spreading - confirm against the package land pattern in the datasheet.
Do not drive the IN pin with voltages above 5.5 V or below -0.3 V referenced to GND; the logic input ESD structures will be damaged. When using the IS current-sense pin, route the trace away from switching nodes (the drain of OUT) to avoid capacitive coupling that perturbs the analog sense signal. Finally, ensure the DEN pin is pulled up to the MCU VCC (not VS) with a 10 kΩ resistor, otherwise fault flags may not be readable at low VS voltages.
Информация о соответствии
AEC-Q100 qualified per the Infineon PROFET+12V automotive family. RoHS and REACH compliant per Infineon product page. Lead-free and halogen-free manufacturing.
