C8051F022 - 25MHz Mixed-Signal MCU | Silicon Labs
Артикул: C8051F022 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
C8051F022 Обзор
A microcontroller such as the C8051F022 integrates a processor core, memory, digital I/O, timers, and analog conversion functions on one mixed-signal system-on-chip. The 8051 architecture belongs to the broader 8-bit microcontroller hierarchy and is suited to compact control systems that require deterministic peripheral integration without a separate external ADC or DAC. Its mixed-signal feature set is particularly useful when analog measurements, control outputs, and digital communications must share one device.
The C8051F022 combines 25 MHz processing performance with 64 kB Flash and 4.25 kB RAM. The 10-bit ADC supports eight channels at up to 100 ksps, while the 12-bit DAC provides two channels for analog output generation. Two comparators support thresholding and basic signal decisions, and five 16-bit timers help implement timing, waveform generation, and periodic control functions. The manufacturer product page identifies the device as analog-intensive and provides the key feature selection for the C8051F02x family.
The device is designed around the CIP-51 8051-compatible core, with integrated mixed-signal peripherals intended to reduce external component count. A 100-pin QFP package provides access to the device's digital and analog resources, but the high pin count also requires careful PCB routing and decoupling. Verified distributor data identifies the commercial orderable variant as C8051F022-GQ in a 100-TQFP package measuring 14 x 14 mm.
Typical uses include industrial measurement and control, data-acquisition systems, analog signal generation, communications equipment, and embedded products requiring simultaneous MCU and analog-peripheral operation. The ADC can sample multiple external inputs, the DAC can produce programmable analog outputs, and the comparators can monitor thresholds without requiring separate comparator ICs. Firmware selection should account for the peripheral mix and the required I/O count rather than treating the MCU only as a general-purpose controller.
For PCB implementation, place bypass capacitors close to the power pins and route sensitive analog signals away from high-current switching paths. The manufacturer documentation should be used to confirm the complete package pinout, electrical limits, programming method, and peripheral multiplexing before layout release. This page combines verified manufacturer and distributor facts with application-oriented design guidance and explicitly flags information not present in the supplied data.
Аналоги без доработки для C8051F022 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с C8051F022 (тот же форм-фактор и посадочное место) — отличается по ADC Resolution, Package, DAC Resolution, Digital I/O Pins, Product Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
C8051F022-GQ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
C8051F021
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →C8051F230-GQ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
C8051F022 Максимальные параметры и электрические характеристики
| Core | 8051-compatible CIP-51 core |
| Processor Architecture | 8-bit |
| Максимальная тактовая частота | 25 MHz |
| Flash Memory | 64 kB |
| RAM | 4.25 kB |
| ADC Resolution | 10-bit |
| ADC Channels | 8 channels |
| ADC Sampling Rate | 100 ksps |
| DAC Resolution | 12-bit |
| DAC Channels | 2 channels |
| Comparators | 2 |
| Timers | 5 x 16-bit timers |
| Digital I/O | 64 digital I/O pins |
| Напряжение питания | 2.7 V to 3.6 V |
| Корпус | 100-TQFP (14 x 14 mm) |
| Тип монтажа | Surface Mount |
| Programming Interface | In-system programmable Flash MCU |
| Analog Features | 10-bit SAR ADC, 12-bit DAC, and 2 comparators |
| Communication Interfaces | Additional communication interfaces; specific list not provided |
| RoHS | Unknown; no verified compliance statement supplied |
| REACH | Unknown; no verified compliance statement supplied |
Руководство по цоколевке C8051F022 в корпусе 100-tqfp (14 x 14 mm)
Цоколевка для C8051F022 (корпус 100-tqfp (14 x 14 mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для C8051F022.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
C8051F022 подходит для 6 применениеs: Industrial Process Measurement, Data-Acquisition Controller, Programmable Analog Output, Embedded Communications Equipment, Automatic Test and Control Equipment, Sensor and Monitoring Node.
Industrial Process Measurement
The C8051F022 fits industrial measurement systems that need local sensor acquisition, control logic, and analog outputs in one device. Its 10-bit, eight-channel ADC can digitize pressure, temperature, level, or current-sensor outputs at up to 100 ksps, while the 8051 core handles scaling, filtering, alarm logic, and digital communication. The 12-bit, two-channel DAC can provide programmable reference or actuator signals where the datasheet-defined output range is sufficient. Compared with a discrete MCU-plus-converter architecture, the integrated mixed-signal peripherals can reduce board area and firmware coordination overhead, although the 10-bit ADC may not satisfy high-accuracy measurement requirements without calibration.
Рекомендуется
Data-Acquisition Controller
The C8051F022 can serve as a compact data-acquisition controller for analog sensors and digital status inputs. The eight-channel, 10-bit ADC provides a practical sampling path for slowly changing or moderately bandwidth-limited signals, while 64 digital I/O pins allow the controller to coordinate triggers, interlocks, and external logic. Firmware can collect samples, apply calibration and filtering, and expose results through the device's communication interfaces. Designers should verify the actual communication peripheral list, package pin multiplexing, and ADC acquisition timing in the official datasheet before assigning channels or planning high-rate signal capture.
Рекомендуется
Programmable Analog Output
The C8051F022 is suitable for embedded systems that require firmware-generated analog references or control outputs. Its 12-bit, two-channel DAC allows two independent output values to be updated by software, which can support stimulus generation, setpoint control, or test-interface functions. The MCU core can calculate output levels from sensor inputs and timer events, while the comparators can provide fast threshold decisions around the generated or measured signals. Because the supplied data does not specify DAC output range, reference voltage, settling time, or output-drive capability, the official electrical specifications must be checked before loading the outputs or designing precision analog front ends.
Рекомендуется
Embedded Communications Equipment
The C8051F022 can support communications-oriented embedded products because the manufacturer identifies additional communication interfaces in addition to its analog peripherals. A system can use the 8051 core for protocol handling, the ADC for incoming analog signals, the DAC for output generation, and the digital I/O for modem, interface, or status signaling. The supplied verified data does not name the available communication peripherals or their package assignments, so interface selection must be confirmed before schematic capture. This makes the device a candidate for compact industrial communications equipment, but not a substitute for a dedicated transceiver or radio front end.
Рекомендуется
Automatic Test and Control Equipment
The C8051F022's combination of ADC, DAC, comparators, timers, and digital I/O makes it relevant to automatic test equipment and embedded control fixtures. A firmware sequence can acquire an analog value, compare it against programmed limits, update a DAC output, and drive digital control lines through timed events. The two comparators are useful for threshold detection, while the five 16-bit timers can support timing and sequencing functions. For accurate stimulus and measurement paths, engineers must verify input range, output range, comparator response, timer resources, and calibration requirements in the manufacturer datasheet; the summary data does not provide those electrical limits.
Рекомендуется
Sensor and Monitoring Node
The C8051F022 can implement a compact sensor-monitoring node when a design needs both measurement and local control. Eight ADC channels can monitor multiple analog sensors, while 64 digital I/O pins provide digital inputs, outputs, and interface connections. The 25 MHz core supports responsive firmware filtering and control, and the DAC offers a way to generate an analog indication or setpoint where suitable. A practical design should budget ADC settling time, account for sensor excitation and noise, and place analog traces away from noisy digital or power paths. The device is most appropriate when integration and local mixed-signal control matter more than very high ADC resolution.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для C8051F022 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | C8051F022-GQ | C8051F021 | C8051F230-GQ |
|---|---|---|---|---|
| Package | 100-TQFP (14 x 14 mm) | 100-TQFP (14 x 14 mm) | QFP100; exact package confirmation required | QFP100; exact package confirmation required |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
Ключевые отличия
- Integrated mixed-signal resources (против C8051F021)
- High integration with 64 digital I/O (против C8051F230-GQ)
- Confirmed orderable package variant (против C8051F022)
Заметки по проектированию
Use the official C8051F022 package drawing to assign all 100 package pins before routing. The verified distributor listing confirms a 100-TQFP, 14 x 14 mm package, but the supplied data does not include the complete pin table. Place decoupling capacitors close to the device power pins and preserve the manufacturer-recommended exposed-pad or thermal land pattern, if applicable to the exact GQ package.
Route analog inputs and DAC outputs as short, quiet traces, keeping them away from digital clocks, high-current outputs, and switching-regulator paths. The ADC can sample up to 100 ksps, so source impedance, acquisition time, and settling behavior must be checked in the official datasheet. For comparator inputs, use controlled routing and guard or shielding techniques when the source signal is high impedance.
Design the supply around the verified 2.7 V to 3.6 V operating range, but do not infer current consumption from the 25 MHz clock frequency. The final regulator, bulk capacitance, and decoupling arrangement should follow the manufacturer power recommendations and the enabled peripheral set. Confirm analog and digital power requirements, startup behavior, and maximum supply tolerances before releasing the power tree.
Do not treat C8051F021 or C8051F230-GQ as drop-in replacements without checking the complete package pinout and peripheral resources. The supplied cross-reference results identify comparison pages but do not verify electrical equivalence. Likewise, the phrase 'additional communication interfaces' does not identify the exact peripheral list, so UART, SPI, I2C, and other interface assignments must be confirmed from the official datasheet.
Информация о соответствии
The supplied verified data does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements for C8051F022. Obtain current manufacturer documentation for the exact orderable suffix.
