CD4060BM - 14-Bit Counter/Divider | Texas Instruments
Артикул: CD4060BM ✓ АктивенCD4060BM Обзор
A CMOS binary counter is a sequential logic device that increments a binary value on each active clock transition. The CD4060BM belongs to the counter and divider hierarchy, within logic ICs and digital timing ICs. Its ripple-counter architecture provides multiple frequency-division outputs, while the oscillator section determines the source frequency used by the internal counting stages. This combination can reduce the need for separate oscillator and divider components in low-to-moderate timing systems.
The verified device information identifies a 14-stage ripple-carry architecture, a 14-bit counter output, 3 V to 18 V supply operation, and operation up to 24 MHz. The 16-SOIC package is a surface-mount package from the SOIC family. The counter uses negative-edge triggering, as identified in the DigiKey listing, which must be considered when connecting it to external clock and reset circuitry. Individual timing-pin and output-pin assignments are not available in the supplied source snippets.
The CD4060BM architecture is useful when a system needs several divided versions of one clock. Each ripple stage provides a progressively divided frequency, allowing a design to obtain multiple timing references without cascading separate divider ICs. Because the device is implemented in CMOS, it belongs to the low-power logic family and can be used in battery-operated or low-leakage digital systems when operated within the documented voltage and frequency limits.
Typical uses include digital clock dividers, pulse-generation circuits, industrial timing modules, periodic-event generators, microcontroller clock subsystems, waveform counters, and laboratory timer boards. In these applications, the integrated oscillator reduces component count, while the divided outputs provide convenient frequencies for counters, displays, control logic, or communication timing. External component selection determines whether the oscillator uses an RC network or a crystal-based arrangement.
Designers should verify oscillator-component values, output-drive requirements, reset timing, and unused-output handling directly against the TI CD4060B datasheet. Maximum operating frequency varies with supply voltage and operating conditions, so a 24 MHz design should not be assumed to work identically across the complete 3 V to 18 V range. Decoupling and unused-input treatment should also follow the manufacturer's recommendations.
This product record combines verified manufacturer, distributor, and cross-reference information with practical selection guidance, packaging details, pricing context, and an honest assessment of drop-in replacement availability. It distinguishes documented electrical facts from parameters that still require confirmation from the complete manufacturer datasheet.
Аналоги без доработки для CD4060BM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиCD4060BM Максимальные параметры и электрические характеристики
| Counter Type | 14-stage ripple-carry binary counter/divider |
| Logic Family | CMOS |
| Number of Count Elements | 1 element |
| Counter Output Width | 14 bit |
| Counting Edge | Negative edge |
| Operating Supply Voltage Range | 3 V to 18 V |
| Maximum Listed Operating Frequency | 24 MHz |
| Oscillator Functions | RC or crystal oscillator circuit support |
| Divider Architecture | 14-stage ripple-carry |
| Package Type | 16-SOIC |
| Тип монтажа | Surface mount |
| Количество выводов | 16 pins |
| Manufacturer | Texas Instruments |
| Device Category | Counter IC |
Руководство по цоколевке CD4060BM в корпусе 16-soic
Цоколевка для CD4060BM (корпус 16-soic). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для CD4060BM.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
CD4060BM подходит для 6 применениеs: Digital Clock Divider, Industrial Periodic Event Generator, Microcontroller Clock and Timer Support, Pulse and Tone Generation, Battery-Powered Sequencing Controller, Test and Measurement Counter.
Digital Clock Divider
The CD4060BM fits digital clock-divider designs because it combines an oscillator with 14 ripple-counting stages in one 16-SOIC package. A single timing network can drive the internal counter, while selected stages provide progressively divided clock outputs for counters, display refresh, and control logic. The device operates from 3 V to 18 V and is listed for operation up to 24 MHz, allowing it to cover both low-voltage logic and faster timing applications. Designers should verify frequency-versus-voltage behavior, reset recovery time, and output loading against the TI datasheet, and should use multiple outputs only when each load remains within the device's specified drive capability.
Рекомендуется
Industrial Periodic Event Generator
The CD4060BM can generate periodic events in industrial control and automation modules by dividing a stable oscillator frequency across its 14 counter stages. This arrangement is useful when different subsystems need related but slower timing intervals without separate divider chains. Its 3 V to 18 V operating range allows use across widely separated logic voltage domains, subject to interface level compatibility. For production designs, engineers must account for oscillator tolerance, reset synchronization, temperature drift, and output rise-time effects. The verified 24 MHz maximum is not a substitute for the complete operating and timing specification, so the selected external timing network and control logic must be checked against the manufacturer datasheet.
Рекомендуется
Microcontroller Clock and Timer Support
The CD4060BM is useful beside a microcontroller when the design requires a divided auxiliary clock, periodic interrupt source, or delayed system event that is independent of the main processor timer. Its negative-edge counting behavior and multiple divided outputs can support sampling, watchdog, communication, or housekeeping timing functions. The 16-SOIC package is convenient for compact industrial-control boards, while the 3 V to 18 V range permits operation across common logic supplies. The generated clock must remain synchronized with firmware expectations, so designers should validate startup, reset release, frequency accuracy, and maximum usable frequency at the actual supply voltage before integrating it into a critical timing path.
Рекомендуется
Pulse and Tone Generation
The integrated oscillator and 14-stage divider make the CD4060BM a practical building block for repetitive pulse or tone generation. A selected counter output can establish the repetition rate, while upstream digital logic determines when that output is gated into the final waveform. Using the SOIC-16 package allows the generator to be placed close to receiving logic and away from long analog paths. The design should account for oscillator jitter, counter propagation delay through the ripple stages, reset pulse width, and output symmetry. Since the supplied information does not include detailed transition-time specifications, engineers should verify waveform quality at the intended supply voltage and output loading using the TI datasheet.
Рекомендуется
Battery-Powered Sequencing Controller
The CD4060BM can support low-power sequencing and periodic housekeeping functions because it is a CMOS logic counter/divider with an integrated oscillator and a 3 V to 18 V operating range. It can initiate delayed actions or create divided timing references without continuously running a more complex processor timing subsystem. For battery equipment, the designer should still evaluate total quiescent current, oscillator duty cycle, leakage, and the load presented by external logic. Those parameters are not available in the supplied snippets and must be taken from the manufacturer datasheet. The device is best suited to low-frequency control functions where its fixed ripple-divider architecture is simpler than a programmable timer.
Рекомендуется
Test and Measurement Counter
The CD4060BM can serve as the timing core of a simple bench counter or periodic-signal measurement instrument by providing an oscillator reference and several divided outputs. Dividers or detection logic can then compare an input event against a known timing interval, while output stages trigger displays or indicators. Its 16-SOIC package simplifies compact instrument construction and its 3 V to 18 V range supports multiple internal logic levels. Measurement accuracy will depend mainly on the reference oscillator and comparator path, not just the counter's stage count. Designers should calibrate the reference, control counter propagation delay, and confirm input and output timing margins against the manufacturer specifications.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для CD4060BM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Ключевые отличия
- Integrated oscillator and divider in one device (против A basic standalone binary counter)
- Broad CMOS supply range (против A 5 V-only TTL counter)
- Fourteen available division stages (против A smaller binary counter)
Заметки по проектированию
Decouple the supply close to the CD4060BM with the capacitance and routing recommended by the TI CD4060B datasheet. Place the device in the logic-voltage portion of the board rather than routing long supply traces between the oscillator and counter sections. Because the verified operating range is 3 V to 18 V, confirm that every connected output remains within the selected supply domain. The supplied excerpts do not contain the complete absolute-maximum table or dynamic-current graph, so those values must be checked before finalizing the power budget.
Place the oscillator's timing components close to the associated CD4060BM pins and keep the oscillator loop compact to reduce sensitivity to board capacitance and nearby switching noise. Route the reset and clock signals away from the oscillator network where possible. The verified sources confirm a 16-SOIC package and negative-edge counting, but they do not provide the individual pin mapping, so the board layout must be checked against the complete manufacturer pinout before routing and before assigning every divided output.
Account for ripple propagation delay when using outputs from different counter stages, especially in zero-delay or synchronous-looking systems. A later stage may not change at the same instant as an earlier stage, and the supplied snippets do not quantify propagation delay or transition time. Use output buffering where multiple destinations, long traces, or high fan-out could disturb timing. Validate the assembled circuit at the intended 3 V to 18 V supply range and at the highest frequency relevant to the design rather than relying only on the listed 24 MHz maximum.
Do not substitute CD4060, MC14527, or TC4060 solely because search results call them equivalent oscillator/counter devices. Confirm the package, pin-by-pin function, reset behavior, supply range, maximum frequency, and output timing against the TI CD4060B datasheet. The supplied cross-reference result explicitly advises checking compatibility. Also avoid assuming that a generic CD4000-family counter has the same pinout, since oscillator and divider arrangements can differ even when the counter width and broad function appear similar.
Информация о соответствии
The supplied verified excerpts do not explicitly state the target part's RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The device is a general-purpose logic IC and is therefore not treated as an AEC-Q100-qualified automotive part.
