DSPIC30F6014AT-30I/PT - 30 MIPS 16-bit DSC, 144KB Flash, TQFP-80
Артикул: DSPIC30F6014AT-30I/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $16.82 | $16,82 |
| 10 | $14.95 | $149,50 |
| 100 | $13.42 | $1.342,00 |
| 500 | $12.2 | $6.100,00 |
| 1.000 | $11.1 | $11.100,00 |
DSPIC30F6014AT-30I/PT Обзор
A Digital Signal Controller (DSC) is a hybrid device that combines the deterministic interrupt response and ease-of-use of a microcontroller with the computational throughput of a Digital Signal Processor (DSP). The dsPIC30F family, sitting in the taxonomy of microcontrollers > MCU > 16-bit MCU > DSC, targets real-time embedded control loops where both fast I/O servicing and math-intensive signal processing must run concurrently on a single chip. Unlike a pure DSP, the dsPIC30F retains a RISC-style Harvard architecture with full C-compiler support, allowing engineers to mix control code with DSP algorithms without managing separate processors.
Key features include 30 MIPS execution (40 MHz oscillator), four 16-bit timers, an 8-channel 10-bit ADC with 200 ksps conversion rate, two UART modules, two SPI ports, one I2C bus, a CAN module, and a 6-channel PWM with up to 16-bit resolution. The device supports 60 digital I/O pins, operates from 4.5V to 5.5V supply, and is rated for the industrial temperature range of -40C to +125C. The on-chip DSP engine accelerates operations such as FIR/IIR filters, FFTs, and matrix math via dedicated MAC (multiply-accumulate) hardware, executing a 16x16-bit MAC in a single cycle.
Typical applications include AC induction motor and BLDC motor control, uninterruptible power supplies (UPS), power factor correction (PFC) controllers, audio processing, sensorless motor control, automotive body controllers, industrial automation (PLC, sensor conditioning), and medical instrumentation such as hearing aids and patient monitors. The CAN interface makes the part particularly suited to automotive networking nodes, while the dual PWM with fault inputs enables three-phase inverter drive.
When designing with this DSC, ensure your firmware uses the dsPIC30F instruction set with the correct PLL configuration (the 30 MIPS rating assumes the internal 4x PLL is engaged from a 7.37 MHz crystal or 10 MHz external source). Use the ICD/ICSP programming interface for in-circuit debug and the DSP library (DSPIC30F DSP Library, Microchip application note CE001) to accelerate algorithm development.
This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для DSPIC30F6014AT-30I/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC30F6014AT-30I/PT (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Package, Core Architecture, ADC, Program Memory (Flash).
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC30F6014A-30I/PT
✅ Прямая замена✓ В наличии
$11.85 / шт.
Открыть даташит →DSPIC30F6014AT-30I/PF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DSPIC30F6014AT-20E/PT
✅ Прямая замена✓ В наличии
$8.55 / шт.
Открыть даташит →DSPIC30F6014A-30I/PF
✅ Прямая замена✓ В наличии
$8.65 / шт.
Открыть даташит →DSPIC30F6014A-20I/PF
✅ Прямая замена✓ В наличии
$9.75 / шт.
Открыть даташит →DSPIC30F6014A-20E/PF
✅ Прямая замена✓ В наличии
$9.45 / шт.
Открыть даташит →DSPIC30F6014AT-30I/PT Максимальные параметры и электрические характеристики
| Core Architecture | dsPIC30F (16-bit DSC) |
| Program Memory (Flash) | 144 KB |
| RAM | 8 KB |
| Maximum CPU Speed | 30 MIPS |
| Clock Frequency | 40 MHz max (with 4x PLL) |
| Supply Voltage (VDD) | 4.5 V to 5.5 V |
| I/O Pins | 60 |
| PWM Channels | 6 (up to 16-bit resolution) |
| UART | 2 |
| SPI | 2 |
| I2C | 1 |
| CAN | 1 |
| Timers (16-bit) | 4 |
| Рабочая температура | -40C to +125C (Industrial) |
| Корпус | TQFP-80 (PT), 12x12 mm |
| Тип монтажа | Surface Mount |
| Lead-Free / RoHS | Yes (LEAD FREE) |
| DSP Engine | Yes (single-cycle 16x16 MAC) |
Конфигурация выводов DSPIC30F6014AT-30I/PT
| Контакт 1 | RGND — Reference ground for ADC (separate analog ground) |
| Контакт 2 | AN0 — Analog input 0 / VREF+ |
| Контакт 3 | AN1 — Analog input 1 |
| Контакт 4 | AN2 — Analog input 2 |
| Контакт 5 | AN3 — Analog input 3 |
| Контакт 6 | AN4 — Analog input 4 |
| Контакт 7 | AN5 — Analog input 5 |
| Контакт 8 | AN6 — Analog input 6 |
| Контакт 9 | AN7 — Analog input 7 |
| Контакт 10 | VDD — Digital supply (4.5V-5.5V) |
| Контакт 11 | VSS — Digital ground |
| Контакт 12 | OSC1 — Crystal oscillator input or external clock in |
| Контакт 13 | OSC2 — Crystal oscillator output |
| Контакт 14 | MCLR — Master clear reset (active-low) |
| Контакт 15 | PGED1 — ICSP programming data line 1 |
| Контакт 16 | PGEC1 — ICSP programming clock line 1 |
| Контакт 17 | PGED2 — ICSP programming data line 2 / I/O |
| Контакт 18 | PGEC2 — ICSP programming clock line 2 / I/O |
| Контакт 19 | PWM1H — PWM channel 1 high-side output |
| Контакт 20 | PWM1L — PWM channel 1 low-side output |
| Контакт 21 | PWM2H — PWM channel 2 high-side output |
| Контакт 22 | PWM2L — PWM channel 2 low-side output |
| Контакт 23 | PWM3H — PWM channel 3 high-side output |
| Контакт 24 | PWM3L — PWM channel 3 low-side output |
| Контакт 25 | FLTA — PWM fault input A (active-low) |
| Контакт 26 | FLTB — PWM fault input B (active-low) |
| Контакт 27 | U1RX — UART1 receive |
| Контакт 28 | U1TX — UART1 transmit |
| Контакт 29 | U2RX — UART2 receive / I/O |
| Контакт 30 | U2TX — UART2 transmit / I/O |
| Контакт 31 | SDI1 — SPI1 data in / I/O |
| Контакт 32 | SDO1 — SPI1 data out / I/O |
| Контакт 33 | SCK1 — SPI1 clock / I/O |
| Контакт 34 | SS1 — SPI1 slave select / I/O |
| Контакт 35 | SDI2 — SPI2 data in / I/O |
| Контакт 36 | SDO2 — SPI2 data out / I/O |
| Контакт 37 | SCK2 — SPI2 clock / I/O |
| Контакт 38 | SS2 — SPI2 slave select / I/O |
| Контакт 39 | SDA — I2C data |
| Контакт 40 | SCL — I2C clock |
| Контакт 41 | C1RX — CAN1 receive / I/O |
| Контакт 42 | C1TX — CAN1 transmit / I/O |
| Контакт 43 | IC1 — Input capture 1 / I/O |
| Контакт 44 | IC2 — Input capture 2 / I/O |
| Контакт 45 | IC3 — Input capture 3 / I/O |
| Контакт 46 | IC4 — Input capture 4 / I/O |
| Контакт 47 | OC1 — Output compare 1 / I/O |
| Контакт 48 | OC2 — Output compare 2 / I/O |
| Контакт 49 | OC3 — Output compare 3 / I/O |
| Контакт 50 | OC4 — Output compare 4 / I/O |
| Контакт 51 | T1CK — Timer1 clock / I/O |
| Контакт 52 | T2CK — Timer2 clock / I/O |
| Контакт 53 | T3CK — Timer3 clock / I/O |
| Контакт 54 | T4CK — Timer4 clock / I/O |
| Контакт 55 | INT0 — External interrupt 0 / I/O |
| Контакт 56 | INT1 — External interrupt 1 / I/O |
| Контакт 57 | INT2 — External interrupt 2 / I/O |
| Контакт 58 | INT3 — External interrupt 3 / I/O |
| Контакт 59 | INT4 — External interrupt 4 / I/O |
| Контакт 60 | AVDD — Analog supply (4.5V-5.5V), bond to VDD |
| Контакт 61 | AVSS — Analog ground, bond to VSS |
| Контакт 62 | VDD — Digital supply |
| Контакт 63 | VSS — Digital ground |
| Контакт 64 | RB0 — Port B bit 0 / I/O |
| Контакт 65 | RB1 — Port B bit 1 / I/O |
| Контакт 66 | RB2 — Port B bit 2 / I/O |
| Контакт 67 | RB3 — Port B bit 3 / I/O |
| Контакт 68 | RB4 — Port B bit 4 / I/O |
| Контакт 69 | RB5 — Port B bit 5 / I/O |
| Контакт 70 | RB6 — Port B bit 6 / I/O |
| Контакт 71 | RB7 — Port B bit 7 / I/O |
| Контакт 72 | RC0 — Port C bit 0 / I/O |
| Контакт 73 | RC1 — Port C bit 1 / I/O |
| Контакт 74 | RC2 — Port C bit 2 / I/O |
| Контакт 75 | RC3 — Port C bit 3 / I/O |
| Контакт 76 | RC4 — Port C bit 4 / I/O |
| Контакт 77 | RC5 — Port C bit 5 / I/O |
| Контакт 78 | RD0 — Port D bit 0 / I/O |
| Контакт 79 | RD1 — Port D bit 1 / I/O |
| Контакт 80 | RD2 — Port D bit 2 / I/O |
Типичное применение
DSPIC30F6014AT-30I/PT подходит для 7 применениеs: Three-Phase PMSM / BLDC Motor Control, Uninterruptible Power Supply (UPS) Control, Automotive Body and HVAC Control, Power Factor Correction (PFC) Controller, Industrial PLC and Sensor Conditioning, Audio and Speech Processing, Industrial Servo and Stepper Drive.
Three-Phase PMSM / BLDC Motor Control
The DSPIC30F6014AT-30I/PT is purpose-built for three-phase brushless motor control, delivering 30 MIPS of deterministic execution and a 16-bit DSP engine capable of 30 MMACS throughput per the Microchip dsPIC30F datasheet. Its six 16-bit PWM outputs with programmable dead-time and fault inputs directly drive a three-phase inverter bridge, while the eight 10-bit ADC channels sample phase currents via dual sample-and-hold. The MCU runs Field-Oriented Control (FOC) algorithms - Park/Clarke transforms, PID current loop, space-vector PWM - in real time, supporting sensorless operation when paired with BEMF ADCs. Drop the part into FOC firmware based on Microchip application note AN1078 to accelerate development.
Рекомендуется
Uninterruptible Power Supply (UPS) Control
Digital UPS controllers use the DSPIC30F6014AT-30I/PT to implement real-time inverter control and grid-synchronization loops. The device's 30 MIPS core and DSP engine perform RMS calculations, SOGI-PLL phase tracking, and sinusoidal PWM generation at 16 kHz switching frequency per Microchip's CE005 reference design. Six PWM channels drive the IGBT/MOSFET half-bridge inverter legs, while four 16-bit timers trigger ADC samples synchronized to the grid zero-crossing. With 144 KB Flash and 60 I/O, the part supports multiple relay-control routines, LCD UI scanning, and CAN/SCPI communication simultaneously. Industrial -40C to +125C operation covers telecom-grade UPS bays.
Рекомендуется
Automotive Body and HVAC Control
Automotive body modules (HVAC blend doors, seat controllers, BCM nodes) leverage the DSPIC30F6014AT-30I/PT for its on-chip CAN 2.0B module, six PWM channels, and 10-bit ADC integration. The DSC reads LIN/CAN frames, drives BLDC blowers or DC motors through MOSFET bridges, and samples temperature/blend-pot sensors at 200 ksps. The 144 KB Flash accommodates CANopen, UDS diagnostics, and motor-control loops concurrently. Operating from 4.5V to 5.5V, the part handles automotive load-dump transients when paired with TVS protection. Reference firmware is available in Microchip's AN2159 automotive networking guide.
Рекомендуется
Power Factor Correction (PFC) Controller
DSPIC30F6014AT-30I/PT implements digital PFC stages for switch-mode power supplies running boost, interleaved, or bridgeless topologies. The device's ADC samples input voltage and inductor current at the PWM switching frequency, executing average-current-mode control and harmonic compensation in the DSP engine per Microchip application note AN1106. With six PWM outputs the controller manages main PFC plus auxiliary synchronous-rectifier channels, while CAN or UART telemetry communicates with the system supervisor. The 30-MIPS throughput supports PFC + LLC two-stage SMPS firmware in a single MCU.
Рекомендуется
Industrial PLC and Sensor Conditioning
The DSPIC30F6014AT-30I/PT integrates sensor signal conditioning, ladder-logic execution, and field-bus comms in a single chip for compact industrial PLC nodes. The DSP engine applies digital filtering (FIR/IIR) to analog inputs sampled by the 10-bit ADC, rejecting mains-frequency hum and sensor noise. Its two UART, two SPI, and one I2C interface connect to RS-485 transceivers, SD cards, and I/O expansion chips; the CAN channel links the node to higher-level fieldbus networks. With 144 KB Flash and 8 KB RAM, the part supports IEC 61131-3 runtime libraries and custom control logic concurrently.
Рекомендуется
Audio and Speech Processing
The DSPIC30F6014AT-30I/PT is well-suited for audio front-ends such as digital hearing aids, voice-recognition front-ends, and intercom systems. The DSP engine accelerates FFT, Goertzel, and biquad filter banks at 30 MMACS per the dsPIC30F library manual, enabling real-time spectral analysis and noise reduction. SPI/I2S channels feed digital audio DACs/ADCs; the 10-bit ADC handles analog mic preamp inputs. Operating from 5V with 144 KB Flash for audio algorithms and 8 KB RAM for buffer storage, the part delivers balanced DSP power and MCU integration in a single TQFP-80 chip.
Рекомендуется
Industrial Servo and Stepper Drive
DSPIC30F6014AT-30I/PT implements closed-loop servo and stepper drives for CNC machines, robotics, and laboratory automation. Six PWM channels drive stepper or servo power stages; the encoder interface (QEI) connects directly to incremental encoders through the dsPIC's input-capture modules. The DSP engine runs PI/PID position, velocity, and torque loops at multi-kHz update rates, while CANopen or EtherCAT (via companion chip) coordinates multi-axis systems. Industrial temperature rating supports factory-floor deployment per Microchip AN1162 servo control guide.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC30F6014AT-30I/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC30F6014A-30I/PT | DSPIC30F6014AT-30I/PF | DSPIC30F6014AT-20E/PT | DSPIC30F6014A-30I/PF | DSPIC30F6014A-20I/PF | DSPIC30F6014A-20E/PF |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-80 (PT) 12x12 mm | TQFP-80 (PT) 12x12 mm | TQFP-80 (PF) 12x12 mm | TQFP-80 (PT) 12x12 mm | TQFP-80 (PF) 12x12 mm | TQFP-80 (PF) 12x12 mm | TQFP-80 (PF) 12x12 mm |
| Core Speed | 30 MIPS (40 MHz) | 30 MIPS | 30 MIPS | 20 MIPS (-33%) | 30 MIPS | 20 MIPS (-33%) | 20 MIPS (-33%) |
| Flash Program Memory | 144 KB | 144 KB | 144 KB | 144 KB | 144 KB | 144 KB | 144 KB |
| RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| Operating Temperature | -40C to +125C (Industrial) | -40C to +125C | -40C to +125C | -40C to +125C (E grade) | -40C to +125C | -40C to +125C | -40C to +125C (E grade) |
| Supply Voltage | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V |
| DSP Engine / MAC | Yes (16x16 single-cycle MAC) | Yes | Yes | Yes | Yes | Yes | Yes |
| PWM Channels | 6 (16-bit) | 6 | 6 | 6 | 6 | 6 | 6 |
Ключевые отличия
- Industrial temperature rating and active life-cycle status (против DSPIC30F6014AT-20E/PT)
- Highest throughput 16-bit DSC in TQFP-80 family (против DSPIC30F6012AT-30I/PF)
- Pin-compatible with tray-packaged DSPIC30F6014A-30I/PT (против DSPIC30F6014A-30I/PT)
Заметки по проектированию
Decouple each VDD/VSS pair with a 100 nF X7R ceramic plus a bulk 10 uF tantalum or aluminum-polymer capacitor placed within 5 mm of the package. The DSPIC30F6014AT-30I/PT draws up to ~120 mA peak at 30 MIPS with all peripherals active; use a 5V LDO rated for at least 250 mA headroom. AVDD/AVSS must be bonded to the digital supply with separate traces if analog noise must be isolated, with a ferrite bead in series and dedicated decoupling for ADC accuracy.
Place the 7.37 MHz or 10 MHz crystal within 10 mm of OSC1/OSC2 and guard the traces with a grounded copper pour. Keep ADC analog traces (AN0-AN7, RGND) away from PWM and switching I/O to avoid digital-coupling noise. The exposed thermal pad on the TQFP-80 is internally connected to VSS and must be soldered to a copper pad of at least 1 square inch for thermal dissipation at full 30 MIPS.
Do not omit the MCLR pull-up (10 kohm to VDD) - the DSC will not start up reliably without it. Ensure the ICSP connector (PGED1/PGEC1) is brought to a 6-pin header for in-circuit firmware update and debug; failure to do so blocks field upgrades. When using the CAN module, an external transceiver (e.g. MCP2551) is mandatory - the on-chip CAN controller is a logic-level peripheral only and cannot drive the bus directly.
Estimated: at 30 MIPS, 5V VDD, and full peripheral activity, total power dissipation is approximately 250-300 mW. With a TQFP-80 junction-to-ambient thermal resistance of around 50 C/W on a 4-layer PCB with 1 sq inch copper, junction temperature rise is ~15C, well inside the +125C industrial limit. For sealed enclosures with no airflow, derate CPU utilization to 50% or switch to a -20E variant for additional margin.
Информация о соответствии
Lead-free per Microchip datasheet; RoHS compliant. AEC-Q100 not applicable for industrial-grade DSC. For automotive-grade equivalent consider dsPIC33F devices qualified to AEC-Q100.