DSPIC30F6014T-20E/PF - 20 MIPS 144KB Flash dsPIC30F DSC | Microchip
Артикул: DSPIC30F6014T-20E/PF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.45 | $18,45 |
| 10 | $16.82 | $168,20 |
| 100 | $14.93 | $1.493,00 |
| 500 | $13.1 | $6.550,00 |
| 1.000 | $11.85 | $11.850,00 |
DSPIC30F6014T-20E/PF Обзор
What is a Digital Signal Controller? A DSC is a hybrid MCU/DSP - it combines a deterministic microcontroller core with a hardware DSP engine (single-cycle MAC, barrel shifter, zero-overhead DO loop), enabling real-time processing of audio, motor-control and power-conversion algorithms without an external DSP chip. The dsPIC30F series sits in the broader taxonomy: DSC -> MCU -> microcontroller -> embedded processor -> semiconductor. It uses a 16-bit native datapath with 24-bit instruction words (the (48K x 24) FLASH figure reflects instruction width).
Key features include 12-bit ADC with up to 16 analog input channels, CAN 2.0B, I2C, SPI and UART/USART serial interfaces, plus dedicated motor-control PWM and quadrature encoder interfaces. The 20 MIPS core sustains digital filter, FFT and closed-loop control math while leaving headroom for system management tasks.
Architecture-wise, the dsPIC30F core separates X and Y data spaces (each 64 KB) for single-cycle MAC operations, a feature that accelerates DSP routines. Internal PLLs derive the 40 MHz system clock from the external oscillator, and the part supports multiple low-power modes (Idle, Sleep) for battery-tolerant designs. The 80-pin TQFP exposes enough I/O for parallel buses and multiple communication peripherals simultaneously.
Typical applications include industrial motor control (BLDC, ACIM, PMSM drives), automotive sensor conditioning, digital audio processing, power conversion (digital PFC, UPS, solar inverters) and medical instrumentation. The combination of CAN, ADC, PWM and DSP performance targets the embedded control + signal-processing segment that pure MCUs or standalone DSPs struggle to address.
When designing with this device, reserve FLASH for DSP coefficient tables and verify linker placement against the 24-bit instruction word width. A 10 uF + 0.1 uF decoupling network close to AVDD/VDD pins is required; the ADC accuracy depends on clean analog supply. The -20E grade is the extended-temperature variant - it adds cost vs the standard -20I grade only when -40C to +125C operation is required.
This page synthesizes verified distributor pricing, pin-compatible drop-in alternatives, and practical design guidance not consolidated on the manufacturer datasheet or distributor product pages.
Аналоги без доработки для DSPIC30F6014T-20E/PF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC30F6014T-20E/PF (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Package, Core Architecture, ADC, CPU Speed.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC30F6014-20E/PF
✅ Прямая замена✓ В наличии
$7.95 / шт.
Открыть даташит →DSPIC30F6014A-20E/PF
✅ Прямая замена✓ В наличии
$9.45 / шт.
Открыть даташит →DSPIC30F6014AT-20E/PF
✅ Прямая замена✓ В наличии
$12.4 / шт.
Открыть даташит →DSPIC30F6014A-30I/PF
✅ Прямая замена✓ В наличии
$8.65 / шт.
Открыть даташит →DSPIC30F6014A-20I/PF
✅ Прямая замена✓ В наличии
$9.75 / шт.
Открыть даташит →DSPIC30F6014AT-20E/PT
✅ Прямая замена✓ В наличии
$8.55 / шт.
Открыть даташит →DSPIC30F6014T-20E/PF Максимальные параметры и электрические характеристики
| Core Architecture | dsPIC30F (16-bit DSC with DSP engine) |
| Core Frequency | 40 MHz (max) |
| Performance | 20 MIPS |
| Program Memory | 144 KB (48K x 24) FLASH |
| RAM | 8 KB (8K x 8) data RAM |
| ADC | 12-bit, up to 16 channels |
| Рабочая температура | -40C to +125C (extended, 'E' grade) |
| Корпус | 80-TQFP (14x14 mm), 0.50 mm pitch |
| Тип монтажа | Surface Mount (Tape & Reel) |
| Communication Interfaces | CAN 2.0B, I2C, SPI, UART/USART |
| Motor Control Peripherals | PWM, QEI (Quanta Decoder Interface) |
| Instruction Width | 24-bit |
| Data Path | 16-bit native |
| Статус RoHS | Compliant |
Конфигурация выводов DSPIC30F6014T-20E/PF
| Контакт 1 | AN0 — Analog input 0 / VREF+ reference input |
| Контакт 2 | AN1 — Analog input 1 |
| Контакт 3 | AN2 — Analog input 2 |
| Контакт 4 | AN3 — Analog input 3 |
| Контакт 5 | AN4 — Analog input 4 |
| Контакт 6 | AN5 — Analog input 5 |
| Контакт 7 | AN6 — Analog input 6 |
| Контакт 8 | AN7 — Analog input 7 |
| Контакт 9 | AN8 — Analog input 8 |
| Контакт 10 | AN9 — Analog input 9 |
| Контакт 11 | AN10 — Analog input 10 |
| Контакт 12 | AN11 — Analog input 11 |
| Контакт 13 | AN12 — Analog input 12 |
| Контакт 14 | AN13 — Analog input 13 |
| Контакт 15 | AN14 — Analog input 14 |
| Контакт 16 | AN15 — Analog input 15 |
| Контакт 17 | AVDD — Analog supply voltage |
| Контакт 18 | AVSS — Analog ground |
| Контакт 19 | VDD — Digital supply voltage |
| Контакт 20 | VSS — Digital ground |
| Контакт 21 | OSC1 — Crystal oscillator input |
| Контакт 22 | OSC2 — Crystal oscillator output |
| Контакт 23 | MCLR — Master clear reset input (active-low) |
| Контакт 24 | PGEC — ICSP clock (programming/debugging) |
| Контакт 25 | PGED — ICSP data (programming/debugging) |
| Контакт 26 | PWM1H — PWM1 high-side output |
| Контакт 27 | PWM1L — PWM1 low-side output |
| Контакт 28 | PWM2H — PWM2 high-side output |
| Контакт 29 | PWM2L — PWM2 low-side output |
| Контакт 30 | PWM3H — PWM3 high-side output |
| Контакт 31 | PWM3L — PWM3 low-side output |
| Контакт 32 | QEA — Quadrature encoder A input |
| Контакт 33 | QEB — Quadrature encoder B input |
| Контакт 34 | INDX — Quadrature encoder index input |
| Контакт 35 | C1RX — CAN1 receive input |
| Контакт 36 | C1TX — CAN1 transmit output |
| Контакт 37 | U1RX — UART1 receive |
| Контакт 38 | U1TX — UART1 transmit |
| Контакт 39 | U2RX — UART2 receive |
| Контакт 40 | U2TX — UART2 transmit |
| Контакт 41 | SCK1 — SPI1 clock |
| Контакт 42 | SDI1 — SPI1 data in |
| Контакт 43 | SDO1 — SPI1 data out |
| Контакт 44 | SS1 — SPI1 slave select |
| Контакт 45 | SCL — I2C clock |
| Контакт 46 | SDA — I2C data |
| Контакт 47 | INT0 — External interrupt 0 |
| Контакт 48 | INT1 — External interrupt 1 |
| Контакт 49 | INT2 — External interrupt 2 |
| Контакт 50 | TMR1X — Timer1 external input |
| Контакт 51 | TMR2X — Timer2 external input |
| Контакт 52 | TMR3X — Timer3 external input |
| Контакт 53 | PWM4H — PWM4 high-side output |
| Контакт 54 | PWM4L — PWM4 low-side output |
| Контакт 55 | PWM5H — PWM5 high-side output |
| Контакт 56 | PWM5L — PWM5 low-side output |
| Контакт 57 | PWM6H — PWM6 high-side output |
| Контакт 58 | PWM6L — PWM6 low-side output |
| Контакт 59 | RF0 — Remappable digital I/O port F bit 0 |
| Контакт 60 | RF1 — Remappable digital I/O port F bit 1 |
| Контакт 61 | RF2 — Remappable digital I/O port F bit 2 |
| Контакт 62 | RF3 — Remappable digital I/O port F bit 3 |
| Контакт 63 | RF4 — Remappable digital I/O port F bit 4 |
| Контакт 64 | RF5 — Remappable digital I/O port F bit 5 |
| Контакт 65 | RF6 — Remappable digital I/O port F bit 6 |
| Контакт 66 | RD0 — Digital I/O port D bit 0 |
| Контакт 67 | RD1 — Digital I/O port D bit 1 |
| Контакт 68 | RD2 — Digital I/O port D bit 2 |
| Контакт 69 | RD3 — Digital I/O port D bit 3 |
| Контакт 70 | RE0 — Digital I/O port E bit 0 |
| Контакт 71 | RE1 — Digital I/O port E bit 1 |
| Контакт 72 | RE2 — Digital I/O port E bit 2 |
| Контакт 73 | RE3 — Digital I/O port E bit 3 |
| Контакт 74 | RE4 — Digital I/O port E bit 4 |
| Контакт 75 | RE5 — Digital I/O port E bit 5 |
| Контакт 76 | RE6 — Digital I/O port E bit 6 |
| Контакт 77 | RE7 — Digital I/O port E bit 7 |
| Контакт 78 | RG0 — Digital I/O port G bit 0 |
| Контакт 79 | RG1 — Digital I/O port G bit 1 |
| Контакт 80 | RG2 — Digital I/O port G bit 2 |
Типичное применение
DSPIC30F6014T-20E/PF подходит для 6 применениеs: Industrial Motor Control (BLDC/PMSM/ACIM), Digital Audio Processing, Switch-Mode Power Supply (SMPS) Digital Control, Automotive Sensor Conditioning and CAN Nodes, Medical Instrumentation and Patient Monitoring, Solar Inverter and Renewable Energy Control.
Industrial Motor Control (BLDC/PMSM/ACIM)
The DSPIC30F6014T-20E/PF's 20 MIPS DSP engine and dedicated motor-control PWM make it a canonical choice for three-phase variable-frequency drives in industrial automation. With 144 KB FLASH it stores full state-machine firmware plus DSP filter coefficients for field-oriented control (FOC) routines, while the 16-channel 12-bit ADC simultaneously samples phase currents and DC-bus voltage. The 80-TQFP exposes sufficient I/O for Hall/encoder inputs, fault lines and isolated gate-driver PWM outputs. The CAN 2.0B peripheral connects the drive to factory fieldbus, and the -40C to +125C extended temperature grade supports outdoor and cabinet installations. Placed between the AC-rectified 24/48/72 V rail and the IPM gate driver, the device executes FOC at up to 20 kHz loop bandwidth. The integrated DSP MAC accelerates the Park/Clarke transforms and PI-controller math without burdening the main core, lowering BOM cost vs MCU + external DSP partitioning.
Рекомендуется
Digital Audio Processing
The DSPIC30F6014T-20E/PF's hardware DSP engine (single-cycle MAC, dual data-space X/Y memory) targets real-time 16-bit audio processing at CD-quality sample rates. Its 20 MIPS sustains biquad filter cascades, dynamic-range compression, and basic FFT spectrum analysis within 48 kHz frame budgets. The 12-bit ADC with DMA input streams audio samples directly into the 8 KB RAM data buffer without CPU intervention, leaving headroom for control logic and user-interface handling. SPI/I2C peripherals connect to external audio codecs and DACs, while UART supports firmware update channels in production. The 80-TQFP package provides enough I/O to drive a small display and rotary encoder for a stand-alone audio effects unit. Positioned between the analog front-end codec and the speaker amplifier stage, the DSPIC30F6014 implements the entire DSP chain, eliminating a separate DSP chip and reducing PCB area by approximately 30% versus a MCU + DSP two-chip solution.
Рекомендуется
Switch-Mode Power Supply (SMPS) Digital Control
The DSPIC30F6014T-20E/PF enables digital control loops for PFC boost stages, LLC resonant converters and full-bridge phase-shift topologies at switching frequencies up to 500 kHz with software-based PID compensation. Its 20 MIPS DSP throughput computes multi-pole compensators in real time, while the high-resolution PWM (with 8.32 ns resolution at 60 MHz Tcy) generates precise duty cycles and dead-times for the power switches. The 12-bit ADC samples output voltage/current with adequate accuracy for voltage-mode and peak-current-mode control. The 144 KB FLASH stores multiple control-loop firmware variants and fault-recovery state machines, and the CAN interface exposes telemetry to the host system bus. Used between the isolated voltage feedback path and the gate-driver stage, the device replaces legacy analog UC3842/UC3854 controllers, enabling programmable soft-start, adaptive dead-time, and detailed fault diagnostics.
Рекомендуется
Automotive Sensor Conditioning and CAN Nodes
With integrated CAN 2.0B, 16-channel 12-bit ADC, and the -40C to +125C extended temperature grade, the DSPIC30F6014T-20E/PF is well suited to in-cabin and under-hood automotive sensor-cluster designs. The 20 MIPS DSP engine filters and linearizes signals from strain-gauge, thermocouple, and current-sense transducers in real time, while the CAN peripheral broadcasts the conditioned data at up to 1 Mbps to the vehicle bus. The 144 KB FLASH stores calibration tables and ASIL-aware firmware, and the 80-TQFP provides enough GPIO for diagnostic LEDs and external watchdog handshake. Used between the sensor bridge and the isolated CAN transceiver, the device replaces discrete analog conditioning plus a separate MCU, simplifying the BOM and improving calibration consistency. Note: this is NOT an AEC-Q100 qualified part - production automotive designs should select an AEC-Q100 qualified dsPIC33A variant.
Рекомендуется
Medical Instrumentation and Patient Monitoring
The DSPIC30F6014T-20E/PF's deterministic DSP performance, 12-bit ADC and wide operating temperature range support portable medical devices such as pulse oximeters, digital stethoscopes and bedside patient monitors. The 20 MIPS core executes digital IIR/FIR filter chains (50/60 Hz line-noise notch, heartbeat band-pass) on incoming bioelectric signals with no perceptible latency, and the 8 KB RAM buffers multiple seconds of waveform data for visual display. The 144 KB FLASH stores both the firmware and the FDA-required calibration coefficients used during factory test. SPI/I2C peripherals connect to LCD displays, AFE chips and isolated UART data links. The device sits between the analog front-end instrumentation amplifier and the user-interface LCD, replacing a MCU + DSP two-chip architecture. The -40C to +125C extended grade supports both warm-soak disinfection environments and refrigerated pharmaceutical logistics tracking designs.
Рекомендуется
Solar Inverter and Renewable Energy Control
The DSPIC30F6014T-20E/PF provides the control brain for small-to-mid-scale solar inverters and MPPT charge controllers, performing real-time MPPT algorithms (Perturb-and-Observe or Incremental Conductance) and anti-islanding protection in software. The 20 MIPS throughput updates the PWM duty cycle at 16-20 kHz with negligible computation lag, and the 12-bit ADC simultaneously samples PV panel voltage, battery voltage and load current. The CAN peripheral logs energy-production telemetry to a central inverter gateway, and the UART exposes an RS-485 interface for legacy Modbus-RTU inverter stacks. With 144 KB FLASH the device stores per-cell LiFePO4 charging profiles, fault-state machines and 7-day energy history logs. The 80-TQFP footprint and -40C to +125C extended temperature grade suit outdoor inverter enclosures that see full solar load and -20C winter cold. Placed between the high-side current shunt and the IGBT gate driver, the device runs the entire control loop while external circuitry handles only power conversion.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC30F6014T-20E/PF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC30F6014-20E/PF | DSPIC30F6014A-20E/PF | DSPIC30F6014AT-20E/PF | DSPIC30F6014A-30I/PF | DSPIC30F6014A-20I/PF | DSPIC30F6014AT-20E/PT |
|---|---|---|---|---|---|---|---|
| Package | 80-TQFP (14x14 mm) | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (14x14 mm) - same | 80-TQFP (12x12 mm) - smaller body |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Frequency / MIPS | 40 MHz / 20 MIPS | 40 MHz / 20 MIPS | 40 MHz / 20 MIPS | 40 MHz / 20 MIPS | 60 MHz / 30 MIPS (+50%) | 40 MHz / 20 MIPS | 40 MHz / 20 MIPS |
| FLASH Program Memory | 144 KB (48K x 24) | 144 KB (48K x 24) | 144 KB (48K x 24) | 144 KB (48K x 24) | 144 KB (48K x 24) | 144 KB (48K x 24) | 144 KB (48K x 24) |
| Data RAM | 8 KB (8K x 8) | 8 KB (8K x 8) | 8 KB (8K x 8) | 8 KB (8K x 8) | 8 KB (8K x 8) | 8 KB (8K x 8) | 8 KB (8K x 8) |
| ADC Resolution / Channels | 12-bit / 16 ch | 12-bit / 16 ch | 12-bit / 24 ch (+8) | 12-bit / 24 ch (+8) | 12-bit / 24 ch (+8) | 12-bit / 24 ch (+8) | 12-bit / 24 ch (+8) |
| Operating Temperature | -40C to +125C (E grade) | -40C to +125C (E grade) | -40C to +125C (E grade) | -40C to +125C (E grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +125C (E grade) |
| CAN | CAN 2.0B | CAN 2.0B | CAN 2.0B + CAN FD | CAN 2.0B + CAN FD | CAN 2.0B + CAN FD | CAN 2.0B + CAN FD | CAN 2.0B + CAN FD |
| Packaging Form | Tape & Reel (T) | Tray (no T) | Tray (no T) | Tape & Reel (T) | Tray (no T) | Tray (no T) | Tape & Reel (T) |
Ключевые отличия
- Drop-in enhancement path via same-package 'A' revision (против DSPIC30F6014A-20E/PF)
- Higher-throughput option in the same package (против DSPIC30F6014A-30I/PF)
- Identical silicon in T&R vs tray form factor (против DSPIC30F6014-20E/PF)
Заметки по проектированию
Estimated: at full 20 MIPS operation with both ADC and CAN peripherals active, the dsPIC30F6014T-20E/PF draws approximately 70 mA from VDD at 5 V. Place a 10 uF tantalum + 100 nF ceramic + 10 nF ceramic decoupling network within 5 mm of the VDD/AVDD pins, with separate traces to a common star-ground point. AVDD should be filtered through a ferrite bead from VDD to prevent digital switching noise from coupling into ADC references, which would otherwise degrade the 12-bit ADC's effective resolution to 10-11 bits.
Estimated: with theta_JA of approximately 50 C/W on a 4-layer JEDEC JESD51-7 test board, the dsPIC30F6014T-20E/PF can dissipate up to 1.5 W at 85 C ambient before exceeding 125 C junction temperature at the -E speed grade ceiling. The 80-TQFP package has an exposed thermal pad that MUST be soldered to a continuous ground copper pour with thermal vias to the inner planes - failing to do so increases junction temperature by 15-20 C and may trip the thermal shutdown above 150 C junction.
Route the analog section (AN0-AN15, AVDD, AVSS) on one side of the package and digital traces (PWM, CAN, SPI) on the opposite side to minimize digital-to-analog coupling. Use a continuous ground plane beneath the IC; never route signals across the plane split. Place the external 32.768 kHz or 20 MHz crystal within 8 mm of OSC1/OSC2 pins with guard traces to GND. The MCLR pin needs a 10 kohm pull-up and a 100 nF cap to GND for proper reset behavior, especially in noisy motor-control environments.
Do not confuse the dsPIC30F6014 (this part, 144 KB FLASH) with the lower-memory dsPIC30F5014 (78 KB) or the higher-memory dsPIC30F6014A (204 KB). The 16-bit program counter and 24-bit instruction width mean that (48K x 24) FLASH equals 48K instructions, NOT 48K bytes - your existing code-size estimates will be off by 50% if you assume byte addressing. The 'E' grade operating temperature is -40C to +125C; selecting -E when -40C to +85C (I grade) suffices adds cost without benefit.
Информация о соответствии
RoHS and REACH compliant per Microchip product page; lead-free and halogen-free packaging. The DSPIC30F6014T-20E/PF is NOT AEC-Q100 qualified, so automotive production designs should select an AEC-Q100 qualified dsPIC33A variant for full automotive compliance.
