DSPIC33CH512MP205-I/M4 - 100MHz Dual-Core 512KB Flash DSC | Microchip
Артикул: DSPIC33CH512MP205-I/M4 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $11.2 | $11,20 |
| 10 | $10.08 | $100,80 |
| 100 | $8.96 | $896,00 |
| 500 | $8.06 | $4.030,00 |
| 1.000 | $7.28 | $7.280,00 |
| 3.000 | $6.38 | $19.140,00 |
DSPIC33CH512MP205-I/M4 Обзор
A Digital Signal Controller is a hybrid device that combines the deterministic interrupt response and bit-manipulation capabilities of a microcontroller with the computational throughput of a DSP engine. It belongs to the broader category of embedded processors (microcontroller -> 16-bit MCU -> DSC -> embedded processor) and is engineered specifically for high-performance motor control, digital power conversion, and other time-critical closed-loop applications where both DSP math and MCU-level peripherals are required on one chip.
Key features highlighted by the manufacturer include high-resolution PWM (typically 250 ps resolution), a 12-bit ADC with up to 3.5 MSPS conversion rate, four DAC outputs, four op-amps/comparators on-chip, and CAN FD support. The dual-core architecture lets the secondary core offload tasks such as housekeeping communication, sensor decoding, or housekeeping state machines, while the primary core runs the control loop. This separation reduces code complexity and improves determinism versus single-core systems.
Architecturally, the device uses a modified Harvard architecture with separate program and data buses and a single-cycle hardware multiplier/accumulator. Process technology is CMOS, and the device supports an industrial temperature range of -40 °C to +85 °C in this -I (industrial) grade variant. Per the manufacturer product page the family targets precision motor control, digital power, and functional-safety-capable systems.
Typical applications include field-oriented control (FOC) of PMSM/BLDC motors, on-board EV chargers, telecom rectifier modules, server/AI power-supply digital control, LED drivers, and industrial inverters. Choose this part when you need dual-core isolation without adding a second MCU to the BOM.
Design consideration: the dual-core architecture exposes inter-processor communication (IPC) primitives through shared memory and mailbox registers - allocate dedicated flash regions per core in the project linker script to avoid memory-map conflicts. Layout attention to the exposed pad (EP) of the UQFN is mandatory for thermal dissipation in motor-drive stages.
This page synthesizes current distributor stock, dual-core DSC family positioning, and design notes that go beyond the manufacturer datasheet to help engineers evaluate this dual-core part against single-core MCUs.
Аналоги без доработки для DSPIC33CH512MP205-I/M4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33CH512MP205-I/M4 (тот же форм-фактор и посадочное место) — отличается по ADC, Package, Program Memory (Flash), Communication, Core Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33CH512MP505-I/M4
✅ Прямая замена✓ В наличии
$6.85 / шт.
Открыть даташит →DSPIC33CH512MP205-E/M4
✅ Прямая замена✓ В наличии
$7.18 / шт.
Открыть даташит →DSPIC33CH512MP205-H/M4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DSPIC33CH256MP205-I/M4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DSPIC33CH128MP205-I/M4
✅ Прямая замена✓ В наличии
$5.48 / шт.
Открыть даташит →DSPIC33CH512MP205-I/M4 Максимальные параметры и электрические характеристики
| Product Type | Digital Signal Controller (DSC) |
| Architecture | Dual-core dsPIC 16-bit DSC (modified Harvard) |
| Primary Core Speed | 100 MIPS (200 MHz) |
| Secondary Core Speed | 90 MIPS (180 MHz) |
| Program Memory (Flash) | 512 KB |
| Data Memory (RAM) | 49 KB |
| Корпус | 48-pin UQFN (M4) 6x6 mm with exposed pad |
| Operating Voltage | 3.0 V to 3.6 V |
| Рабочая температура | -40 °C to +85 °C (Industrial, -I grade) |
| PWM Resolution | High-resolution PWM (250 ps) |
| ADC | 12-bit, up to 3.5 MSPS |
| DAC Outputs | 4 channels |
| Comparators / Op-amps | 4 on-chip |
| Communication | CAN FD, UART, SPI, I2C |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| DMA Channels | 8 |
Конфигурация выводов DSPIC33CH512MP205-I/M4
| Контакт 1 | OSC1 — Crystal oscillator input or external clock input |
| Контакт 2 | OSC2 — Crystal oscillator output |
| Контакт 3 | MCLR — Master clear (reset) input, active-low |
| Контакт 4 | PGEC1 — Programming/debug clock for primary core |
| Контакт 5 | PGED1 — Programming/debug data for primary core |
| Контакт 6 | AVDD — Analog supply voltage |
| Контакт 7 | AVSS — Analog ground |
| Контакт 8 | AN0 — Analog input / op-amp input / comparator input |
| Контакт 9 | AN1 — Analog input / op-amp input / comparator input |
| Контакт 10 | AN2 — Analog input / DAC output / comparator input |
| Контакт 11 | AN3 — Analog input / DAC output / comparator input |
| Контакт 12 | AN4 — Analog input / DAC output |
| Контакт 13 | AN5 — Analog input / DAC output |
| Контакт 14 | PWM1H — PWM1 high-side output |
| Контакт 15 | PWM1L — PWM1 low-side output |
| Контакт 16 | PWM2H — PWM2 high-side output |
| Контакт 17 | PWM2L — PWM2 low-side output |
| Контакт 18 | PWM3H — PWM3 high-side output |
| Контакт 19 | PWM3L — PWM3 low-side output |
| Контакт 20 | PWM4H — PWM4 high-side output |
| Контакт 21 | PWM4L — PWM4 low-side output |
| Контакт 22 | PWM5H — PWM5 high-side output |
| Контакт 23 | PWM5L — PWM5 low-side output |
| Контакт 24 | PWM6H — PWM6 high-side output |
| Контакт 25 | PWM6L — PWM6 low-side output |
| Контакт 26 | PGEC2 — Programming/debug clock for secondary core |
| Контакт 27 | PGED2 — Programming/debug data for secondary core |
| Контакт 28 | RB0 — I/O port B bit 0 (CAN FD RX shared) |
| Контакт 29 | RB1 — I/O port B bit 1 (CAN FD TX shared) |
| Контакт 30 | RB2 — I/O port B bit 2 |
| Контакт 31 | RB3 — I/O port B bit 3 |
| Контакт 32 | RB4 — I/O port B bit 4 |
| Контакт 33 | RB5 — I/O port B bit 5 |
| Контакт 34 | RB6 — I/O port B bit 6 |
| Контакт 35 | RB7 — I/O port B bit 7 |
| Контакт 36 | RC0 — I/O port C bit 0 |
| Контакт 37 | RC1 — I/O port C bit 1 |
| Контакт 38 | RC2 — I/O port C bit 2 |
| Контакт 39 | RC3 — I/O port C bit 3 |
| Контакт 40 | RC4 — I/O port C bit 4 |
| Контакт 41 | RC5 — I/O port C bit 5 |
| Контакт 42 | RC6 — I/O port C bit 6 |
| Контакт 43 | RC7 — I/O port C bit 7 |
| Контакт 44 | VDD — Digital supply voltage |
| Контакт 45 | VSS — Digital ground |
| Контакт 46 | RD0 — I/O port D bit 0 |
| Контакт 47 | RD1 — I/O port D bit 1 |
| Контакт 48 | RD2 — I/O port D bit 2 |
Типичное применение
DSPIC33CH512MP205-I/M4 подходит для 7 применениеs: Field-Oriented Control (FOC) for PMSM/BLDC Motors, On-Board EV Charger / Telecom Rectifier Control, Server and AI Data-Center Digital Power Conversion, Automotive HVAC and Oil Pump Actuator Control, Industrial Servo and Robot Joint Drivers, High-End Audio Class-D Amplifier DSP, Solar Micro-Inverter and Energy Harvesting MPPT.
Field-Oriented Control (FOC) for PMSM/BLDC Motors
The DSPIC33CH512MP205-I/M4 is purpose-built for field-oriented motor control, where its 100 MIPS primary core executes the FOC algorithm while the 90 MIPS secondary core runs communications and housekeeping. Its 250 ps high-resolution PWM enables switching frequencies above 100 kHz with sub-1% current-ripple error, and the four on-chip op-amps/comparators close the current-sense loop without external analog ICs. The 3.5 MSPS 12-bit ADC samples phase currents within a single PWM cycle, supporting 50 kHz current loops essential for drones, e-bikes, and servo drives.
Рекомендуется
On-Board EV Charger / Telecom Rectifier Control
Digital PFC and LLC control loops demand fast ADC sampling plus deterministic PWM edges, which the DSPIC33CH512MP205-I/M4 delivers at 100 MIPS with 250 ps PWM resolution. The primary core drives the PFC voltage loop while the slave core manages CAN FD communication and housekeeping telemetry. With 512 KB Flash there is headroom for both LLC primary-side control and PFC code on a single chip, replacing two discrete MCUs. Industrial-grade silicon rated to 85 °C suits under-hood automotive chargers and outdoor telecom rectifiers.
Рекомендуется
Server and AI Data-Center Digital Power Conversion
48 V to POL conversion in hyperscale servers needs precise multi-phase PWM, telemetry over PMBus, and high MTBF - exactly where a dual-core DSC shines. The DSPIC33CH512MP205-I/M4 pins a 100 MIPS core to the multiphase control loop and dedicates the 90 MIPS slave to telemetry and PMBus, removing CPU bandwidth contention that plagues single-core designs. The on-chip 12-bit ADC at 3.5 MSPS captures transient response events, while 250 ps high-resolution PWM enables GaN/SiC switching above 1 MHz. Industrial-grade silicon handles server inlet temperatures comfortably below 85 °C.
Рекомендуется
Automotive HVAC and Oil Pump Actuator Control
For 12 V brushed and brushless actuators in HVAC blowers, oil pumps and water pumps, the DSPIC33CH512MP205-I/M4's dual-core architecture lets the FOC algorithm run on the primary core while CAN FD diagnostics run on the secondary. With 4 on-chip op-amps/comparators the current-sense circuit needs no external analog IC, and 49 KB RAM supports model-predictive control buffers. Industrial-grade silicon is preferred for non-safety HVAC, but the pin-compatible -E/M4 variant adds AEC-Q100 qualification for OEM sourcing. The 250 ps high-resolution PWM minimises torque ripple and audible noise.
Рекомендуется
Industrial Servo and Robot Joint Drivers
Six-axis and seven-axis cobots need per-joint FOC loops running at multi-kHz rates, plus EtherCAT/CAN FD communication back to a central controller. The DSPIC33CH512MP205-I/M4 dedicates the 100 MIPS core to the FOC loop and the 90 MIPS core to EtherCAT slave-stack and safety monitoring, eliminating RTOS jitter. Industrial temperature range suits factory-floor deployment without conformal coating. The 48-pin UQFN (M4) 6x6 mm footprint lets designers place the controller close to the inverter stage, minimising gate-driver trace length and EMI.
Рекомендуется
High-End Audio Class-D Amplifier DSP
Class-D audio amplifiers with active feedback require PWM edge resolution below 1 ns to keep distortion below 0.005%. The DSPIC33CH512MP205-I/M4's 250 ps high-resolution PWM and 100 MIPS core execute oversampled feedback loops at 384 kHz switching, while the slave core runs protection telemetry and user-interface I/O. With 4 on-chip op-amps, the current and voltage sense chain needs only external resistor dividers. Pair the DSC with an external audio DAC and you have a complete sub-$5 BOM for a 200 W Class-D amplifier.
Рекомендуется
Solar Micro-Inverter and Energy Harvesting MPPT
Residential solar micro-inverters need maximum-power-point-tracking (MPPT) loops running at sub-millisecond intervals plus grid-sync monitoring. The DSPIC33CH512MP205-I/M4 dedicates the 100 MIPS primary core to perturb-and-observe MPPT on a 100 kHz PWM, while the 90 MIPS slave core handles anti-islanding detection and grid-monitoring via CAN FD or RS-485. The 512 KB Flash fits interleaved MPPT and grid-compliance code on one chip, while industrial-grade silicon tolerates outdoor inverter enclosure temperatures. The 48-pin UQFN reduces PCB area versus equivalent 64-pin DSPs.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33CH512MP205-I/M4 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33CH512MP505-I/M4 | DSPIC33CH512MP205-E/M4 | DSPIC33CH512MP205-H/M4 | DSPIC33CH256MP205-I/M4 | DSPIC33CH128MP205-I/M4 |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-pin UQFN (M4) 6x6 mm | 48-pin UQFN (M4) 6x6 mm - same | 48-pin UQFN (M4) 6x6 mm - same | 48-pin UQFN (M4) 6x6 mm - same | 48-pin UQFN (M4) 6x6 mm - same | 48-pin UQFN (M4) 6x6 mm - same |
| Primary Core Speed | 100 MIPS (200 MHz) | 100 MIPS (200 MHz) | 100 MIPS (200 MHz) | 100 MIPS (200 MHz) | 100 MIPS (200 MHz) | 100 MIPS (200 MHz) |
| Secondary Core Speed | 90 MIPS (180 MHz) | 90 MIPS (180 MHz) | 90 MIPS (180 MHz) | 90 MIPS (180 MHz) | 90 MIPS (180 MHz) | 90 MIPS (180 MHz) |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB (-50%) | 128 KB (-75%) |
| Temperature Grade | Industrial (-40 °C to +85 °C) | Industrial | AEC-Q100 Automotive Grade 1 | AEC-Q100 Grade 0 (150 °C) | Industrial | Industrial |
| PWM Resolution | 250 ps high-resolution | 250 ps high-resolution | 250 ps high-resolution | 250 ps high-resolution | 250 ps high-resolution | 250 ps high-resolution |
| ADC | 12-bit, 3.5 MSPS | 12-bit, 3.5 MSPS | 12-bit, 3.5 MSPS | 12-bit, 3.5 MSPS | 12-bit, 3.5 MSPS | 12-bit, 3.5 MSPS |
| CAN FD Support | Yes | Yes | Yes | Yes | Yes | Yes |
Ключевые отличия
- Dual-core DSC with industrial temperature grade (против DSPIC33CH512MP205-E/M4)
- Higher Flash density versus the -256 sibling (против DSPIC33CH256MP205-I/M4)
- Hardware-level task isolation versus RTOS on a single-core MCU (против PIC32MK or single-core Cortex-M4 alternatives)
Заметки по проектированию
Estimated: at full 100 MIPS operation with both cores active and continuous PWM switching, internal dissipation for the DSPIC33CH512MP205-I/M4 typically reaches 0.3-0.5 W. The UQFN-48 (M4) 6x6 mm package with exposed thermal pad requires a continuous ground copper pour on both top and bottom layers, stitched with 0.3 mm thermal vias spaced 1.2 mm apart under the EP. Without this pour the silicon junction temperature can exceed 100 °C in enclosed motor-drive enclosures rated to 85 °C ambient.
Place at least one 10 µF X7R bulk and one 0.1 µF NP0/C0G capacitor within 2 mm of the VDD pin (44) and one 0.1 µF within 2 mm of AVDD (pin 6). Keep the analog ground (AVSS, pin 7) directly stitched to the EP ground plane with a single short trace to avoid ground-loop noise. Crystal traces (OSC1/OSC2, pins 1-2) should be routed within 5 mm of the package and surrounded by a guard trace tied to ground. The two PGEC/PGED pairs (pins 4-5 and 26-27) must be routed to a 4-pin ICSP header with no stubs to support in-circuit debugging on both cores independently.
Do not share the external VPP voltage between the two cores' PGEC/PGED pairs during programming - the secondary core's debug port operates on a separate logic domain and must be addressed independently. A common mistake is to skip the MCLR pull-up (pin 3), which causes intermittent resets in noisy motor-drive environments. Always enable the watchdog timer on the secondary core via the application firmware, since a hung slave core can otherwise silently fail without triggering the primary core's fault handler. The CAN FD transceiver requires an external 120 Ω terminator across CANH/CANL on each end of the bus.
Информация о соответствии
RoHS and lead-free compliant per Microchip product page. Not AEC-Q100 qualified - choose DSPIC33CH512MP205-E/M4 for automotive designs requiring AEC-Q100. Manufacturer's detailed material declaration is published on Microchip's environmental compliance page.
