DSPIC33EP128MC202-I/MM - 70 MIPS DSC, 128KB Flash | Microchip
Артикул: DSPIC33EP128MC202-I/MM ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.82 | $6,82 |
| 10 | $6.35 | $63,50 |
| 100 | $5.75 | $575,00 |
| 500 | $5.3 | $2.650,00 |
| 1.000 | $4.9 | $4.900,00 |
DSPIC33EP128MC202-I/MM Обзор
A digital signal controller combines the computational capability of a digital signal processor with the control peripherals and ease of use of a microcontroller, sitting in the hierarchy DSC -> 16-bit microcontroller -> embedded processor -> system-on-chip. The dsPIC33EP family integrates a DSP engine with single-cycle MAC and 40-bit accumulators alongside standard MCU peripherals, making it a go-to choice for embedded control loops that also require signal processing.
Key features include high-speed PWM modules with complementary outputs and dead-time control, an MCPWM unit, quadrature encoder interface (QEI), two on-chip operational amplifiers, three comparators, and a 10-bit ADC - all purpose-built for precision motor control.
The device operates from a 3V to 3.6V supply across an industrial temperature range of -40C to +85C (the -I suffix), supports in-circuit serial programming (ICSP) via any PGECx/PGEDx pin pair, and includes IEEE 1149.2-compatible JTAG boundary scan for production test.
Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, switched-mode power supplies, digital lighting ballasts, and embedded control systems requiring DSP-class math.
Design tip: connect all VDD, VSS, AVDD and AVSS pins and use any single PGECx/PGEDx pair consistently for programming - mixing pairs causes ICSP failures.
This page adds distributor pricing tiers, verified drop-in alternatives within the same package, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для DSPIC33EP128MC202-I/MM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP128MC202-I/MM (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Package, Core, Program Memory (Flash), RAM.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33EP128MC202-I/ML
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP128MC202-E/MM
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →DSPIC33EP64MC202-I/MM
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$2.29 / шт.
Открыть даташит →DSPIC33EP32MC202-I/MM
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$2.25 / шт.
Открыть даташит →DSPIC33EP128MC202-I/SP
✅ Прямая замена✓ В наличии
$3.94 / шт.
Открыть даташит →DSPIC33EP128MC202-I/MM Максимальные параметры и электрические характеристики
| Core | dsPIC33E 16-bit DSC core |
| Maximum MIPS | 70 MIPS |
| Instruction Clock Frequency | 60 MHz |
| Program Memory (Flash) | 128 KB (43K x 24) |
| RAM | 16 KB |
| Supply Voltage Range | 3 V to 3.6 V |
| Рабочая температура | -40C to +85C |
| Корпус | 28-QFN-S (6x6 mm), exposed pad |
| Число выводов | 28 |
| Тип монтажа | Surface Mount |
| PWM Modules | MCPWM, high-speed complementary outputs |
| Quadrature Encoder Interface | Yes (QEI) |
| On-chip Op-Amps | 2 |
| Comparators | 3 |
| In-Circuit Serial Programming | Yes (ICSP via PGECx/PGEDx pairs) |
| JTAG | IEEE 1149.2 compatible boundary scan |
| Статус RoHS | RoHS compliant |
Конфигурация выводов DSPIC33EP128MC202-I/MM
| Контакт 1 | MCLR — Master clear reset (active low), programming voltage input |
| Контакт 2 | AN0/VREF+/CN2/RB0 — Analog input 0 / positive voltage reference / change notification / port B bit 0 |
| Контакт 3 | AN1/VREF-/CN3/RB1 — Analog input 1 / negative voltage reference / change notification / port B bit 1 |
| Контакт 4 | AN2/SS1/CN4/RB2 — Analog input 2 / SPI slave select / change notification / port B bit 2 |
| Контакт 5 | AN3/INDX/CN5/RB3 — Analog input 3 / QEI index input / change notification / port B bit 3 |
| Контакт 6 | AN4/RP1/RC13 — Analog input 4 / peripheral pin select remappable pin / port C bit 13 |
| Контакт 7 | AN5/RP2/RC14 — Analog input 5 / peripheral pin select remappable pin / port C bit 14 |
| Контакт 8 | VDD — Positive supply (3V to 3.6V) |
| Контакт 9 | VSS — Ground reference |
| Контакт 10 | OSC1/CLKI/RA2 — Crystal oscillator input / external clock input / port A bit 2 |
| Контакт 11 | OSC2/CLKO/RA3 — Crystal oscillator output / clock output / port A bit 3 |
| Контакт 12 | SOSCI/CN1/RB4 — Secondary oscillator input / change notification / port B bit 4 |
| Контакт 13 | SOSCO/T1CK/CN0/RA4 — Secondary oscillator output / Timer1 external clock / change notification / port A bit 4 |
| Контакт 14 | VDD — Positive supply (3V to 3.6V) |
| Контакт 15 | VSS — Ground reference |
| Контакт 16 | PGED3/OC1/RB5 — Programming data channel 3 / output compare 1 / port B bit 5 |
| Контакт 17 | PGEC3/AN6/OC2/RB6 — Programming clock channel 3 / analog input 6 / output compare 2 / port B bit 6 |
| Контакт 18 | PGD0/AN7/VREF-/CN7/RB7 — Programming data channel 0 / analog input 7 / negative voltage reference / change notification / port B bit 7 |
| Контакт 19 | PGC0/AN8/VREF+/CN8/RB8 — Programming clock channel 0 / analog input 8 / positive voltage reference / change notification / port B bit 8 |
| Контакт 20 | PGD1/AN9/PWM1L/RB9 — Programming data channel 1 / analog input 9 / PWM1 low-side output / port B bit 9 |
| Контакт 21 | PGC1/TDI/PWM1H/RB10 — Programming clock channel 1 / JTAG data in / PWM1 high-side output / port B bit 10 |
| Контакт 22 | TDO/PWM2L/RB11 — JTAG data out / PWM2 low-side output / port B bit 11 |
| Контакт 23 | TCK/PWM2H/RB12 — JTAG test clock / PWM2 high-side output / port B bit 12 |
| Контакт 24 | AN10/CTPLS/PWM3L/RB13 — Analog input 10 / CTMU pulse output / PWM3 low-side output / port B bit 13 |
| Контакт 25 | AN11/PWM3H/CVREF/RB14 — Analog input 11 / PWM3 high-side output / comparator voltage reference / port B bit 14 |
| Контакт 26 | AN12/PWM4L/RB15 — Analog input 12 / PWM4 low-side output / port B bit 15 |
| Контакт 27 | AVSS — Analog ground reference |
| Контакт 28 | AVDD — Analog positive supply |
Типичное применение
DSPIC33EP128MC202-I/MM подходит для 6 применениеs: BLDC Motor Control, PMSM Field-Oriented Control Drives, Switch-Mode Power Supplies, Digital Lighting Ballasts and LED Drivers, Embedded Sensing and DSP Signal Conditioning, Robotics and Factory Automation Nodes.
BLDC Motor Control
The DSPIC33EP128MC202-I/MM fits BLDC drives because its high-speed PWM module generates complementary outputs with programmable dead-time, and its QEI, two op-amps and three comparators cover position sensing and current-sampling signal chains without extra components. In a typical three-phase inverter, the DSC runs field-oriented control at 70 MIPS with single-cycle MAC math while the PWM module drives gate drivers at high carrier frequencies. The 10-bit ADC synchronized to the PWM enables accurate shunt-based phase-current sampling. Because the core executes DSP-grade multiply-accumulate in hardware, control loop rates of 10-20 kHz are achievable without CPU saturation.
Рекомендуется
PMSM Field-Oriented Control Drives
For permanent-magnet synchronous motors, the DSPIC33EP128MC202-I/MM provides the compute and peripheral combination that FOC demands: a 70 MIPS DSP engine for Clarke/Park transforms and PI current loops, complementary PWM with dead-time insertion to prevent shoot-through, and quadrature encoder interface for rotor position from incremental encoders. The two on-chip op-amps can amplify low-level shunt resistor voltages before the ADC, reducing external BOM cost. With 128 KB of Flash there is ample room for sensorless observer algorithms alongside communication stacks. Designers should synchronize ADC sampling to the PWM center to minimize switching-noise coupling into current measurements.
Рекомендуется
Switch-Mode Power Supplies
The DSPIC33EP128MC202-I/MM suits digitally controlled SMPS because its high-speed PWM supports complementary outputs, dead-time and fast fault trip inputs, enabling phase-shifted full-bridge and synchronous buck topologies. The 70 MIPS core closes voltage/current loops fast enough for 100-500 kHz converters, while comparators support cycle-by-cycle overcurrent protection in hardware, independent of firmware latency. The 3V-3.6V operation matches standard logic rails, and the 6x6 mm QFN-S with exposed pad gives good thermal path for dense power boards. Digital power benefits from the ability to update firmware-control laws without hardware redesign.
Рекомендуется
Digital Lighting Ballasts and LED Drivers
The DSPIC33EP128MC202-I/MM is used in high-intensity discharge (HID) ballast and high-power LED driver designs, where its complementary PWM with dead-time drives half-bridge resonant stages and its comparators provide lamp-fault and overcurrent protection. The 70 MIPS DSP headroom handles ignition sequencing, resonance-frequency tracking and dimming control algorithms simultaneously. With 128 KB Flash, full lamp-state machines plus DALI or DMX communication fit on one chip. The industrial -40C to +85C rating covers luminaires in outdoor and cold-storage environments, and the 28-pin QFN-S keeps controller footprint minimal inside compact driver enclosures.
Рекомендуется
Embedded Sensing and DSP Signal Conditioning
Beyond motion, the DSPIC33EP128MC202-I/MM serves data-acquisition nodes needing on-board DSP: the hardware MAC engine filters and transforms sensor streams at 70 MIPS while the two op-amps and three comparators condition signals before the 10-bit ADC. This makes it effective for vibration monitors, ultrasonic sensors and power-quality meters where FFT or filter banks run locally. The 16 KB RAM buffers sample windows, and 128 KB Flash stores calibration and compensation tables. ICSP field-programmability allows firmware updates in installed systems via the PGECx/PGEDx header, and JTAG boundary scan supports production board test.
Рекомендуется
Robotics and Factory Automation Nodes
In automation equipment, the DSPIC33EP128MC202-I/MM acts as a dedicated motion-control coprocessor, offloading servo loops from a host controller. The QEI reads incremental encoders from servo motors, complementary PWM drives H-bridges, and the 70 MIPS core implements cascade position/velocity/current loops. 128 KB Flash accommodates trapezoidal and S-curve motion profiles plus a CAN or UART link to a higher-level PLC. Its industrial temperature rating and active lifecycle status make it dependable for multi-year production programs. Designers should reserve one PWM fault input wired to gate-driver fault outputs for hardware-level shutdown during overcurrent events.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP128MC202-I/MM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP128MC202-I/ML | DSPIC33EP128MC202-E/MM | DSPIC33EP64MC202-I/MM | DSPIC33EP128MC202-I/SP |
|---|---|---|---|---|---|
| Package | 28-QFN-S (6x6 mm) | 28-QFN-S (6x6 mm) - same | 28-QFN-S (6x6 mm) - same | 28-QFN-S (6x6 mm) - same | 28-SPDIP - different footprint |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Program Memory | 128 KB | 128 KB | 128 KB | 64 KB | 128 KB |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| Core Speed | 70 MIPS / 60 MHz | 70 MIPS / 60 MHz | 70 MIPS / 60 MHz | 70 MIPS / 60 MHz | 70 MIPS / 60 MHz |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +125C | -40C to +85C | -40C to +85C |
| Motor-Control Peripherals (PWM/QEI/OpAmp/Comp) | Yes / Yes / 2 / 3 | Yes / Yes / 2 / 3 | Yes / Yes / 2 / 3 | Yes / Yes / 2 / 3 | Yes / Yes / 2 / 3 |
| Supply Voltage | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V |
Ключевые отличия
- Maximum Flash in the 28-pin MC202 family (против DSPIC33EP64MC202-I/MM)
- Extended temperature option available in the identical footprint (против DSPIC33EP128MC202-E/MM)
- QFN-S package with exposed pad (против DSPIC33EP128MC202-I/SP)
Заметки по проектированию
Connect ALL power pins: the dsPIC33EP128MC202 has two VDD/VSS pairs plus separate AVDD/AVSS for the analog domain. Per Microchip documentation, leaving even one power pin unconnected can cause ICSP programming failure and unreliable operation. Decouple each VDD pin with a 100 nF ceramic capacitor placed within 2-3 mm of the pin, plus one bulk 10 uF per rail. Tie AVDD through an RC filter (e.g. 10 ohm + 1 uF) from VDD to reduce digital noise coupling into the 10-bit ADC.
The device provides multiple PGECx/PGEDx programming pin pairs (channels 0, 1 and 3 on this 28-pin part). You must use pins from the SAME pair - if ICSPCLK is routed to PGEC1, ICSPDAT must go to PGED1; mixing pairs causes silent programming failures. Place the programming header on the target board and keep traces under 10 cm. Configure CONFIG register MCLRE and debug settings consistently with your programming tool (PICkit 4 or ICD 4 in MPLAB X).
The 28-QFN-S (6x6 mm) exposed pad must be soldered to a grounded copper pour - it is the primary thermal and ground return path. Estimated: at 60 MHz full activity, typical DSC core current on the order of tens of mA at 3.3 V yields under 150 mW dissipation, so no heatsinking is required for the DSC itself; the exposed pad mainly improves signal integrity. Follow the Microchip layout guidelines for QFN paddle solder voiding - use at least a 3x3 via array under the pad.
For motor-control designs, route PWM outputs away from analog inputs (AN0-AN12 on port B) and keep the crystal circuit (OSC1/OSC2 and SOSCI/SOSCO) compact with ground guarding. Use peripheral pin select (PPS) to move UART/SPI functions away from noisy PWM traces. Synchronize ADC sampling with the PWM period using the ADC trigger feature rather than free-running sampling, so current measurements occur at PWM center and avoid switch-node transients.
Информация о соответствии
RoHS compliant per JLCPCB part listing. Lifecycle status Active per Jotrin. AEC-Q100 qualification not stated in provided data.
