DSPIC33EP128MU206-I/MR - 16-bit 70 MIPS DSC 128KB | Microchip
Артикул: DSPIC33EP128MU206-I/MR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.2 | $6,20 |
| 10 | $5.6 | $56,00 |
| 100 | $4.95 | $495,00 |
| 500 | $4.5 | $2.250,00 |
| 1.000 | $4.1 | $4.100,00 |
DSPIC33EP128MU206-I/MR Обзор
A digital signal controller combines the computational strengths of a microcontroller (MCU) with the math acceleration of a digital signal processor (DSP). In the power-management hierarchy of embedded systems, a DSC sits between general-purpose MCUs and dedicated DSPs, offering deterministic interrupt latency, hardware multiply-accumulate units, and DSP-style addressing modes while retaining the peripherals and ease of use of a classic microcontroller.
Key features of the DSPIC33EP128MU206 include 70 MIPS sustained core performance at 3.3V, a 12-bit ADC capable of high-rate sampling for control loops, USB 2.0 full-speed device support (the MU suffix denotes USB capability), 128 KB of self-programmable Flash with ECC, and a rich peripheral set of timers, UARTs, SPI, and I2C modules typical of the dsPIC33EP family.
Architecturally, the dsPIC33EP core uses a modified Harvard pipeline with DSP engine instructions (MAC, MPY, dual operand fetch), zero-overhead loops, and hardware division support. Program Flash is 43K x 24-bit instruction words; the 16 KB SRAM supports DMA transfers to offload the CPU during high-throughput ADC and USB operation.
Typical applications include digital power supplies and power factor correction, motor control (BLDC, PMSM, ACIM), USB-enabled industrial sensing nodes, and general embedded control where DSP math and real-time performance are required.
When designing with this device, budget the peripheral pin select (PPS) mapping early and confirm the 9x9 mm VQFN thermal pad layout on the PCB, as the exposed pad is the primary heat-removal path.
This page synthesizes distributor availability data, drop-in alternatives, and practical design guidance not found in the raw manufacturer datasheet, with pricing references noted as of 2026-09-24.
Аналоги без доработки для DSPIC33EP128MU206-I/MR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP128MU206-I/MR (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Program Memory (Flash), RAM, Communication Interfaces.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33EP256MU206-I/MR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP64MU206-I/MR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP128MU206-H/MR
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →DSPIC33EP128MU206-E/MR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP128MC206-I/MR
✅ Прямая замена✓ В наличии
$0.13 / шт.
Открыть даташит →DSPIC33EP128MU206-I/MR Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC33EP DSC |
| Maximum Performance | 70 MIPS |
| Program Memory (Flash) | 128 KB (43K x 24) |
| RAM | 16 KB |
| ADC Resolution | 12-bit |
| USB | USB 2.0 full-speed (MU family feature) |
| Рабочая температура | -40C to +85C (Industrial, I suffix) |
| Корпус | 64-pin VQFN (MR), 9x9 mm |
| Тип монтажа | Surface Mount |
| Communication Interfaces | UART, SPI, I2C (peripheral set per dsPIC33EP family) |
Руководство по цоколевке DSPIC33EP128MU206-I/MR в корпусе 64-pin vqfn (mr), 9x9 mm
Цоколевка для DSPIC33EP128MU206-I/MR (корпус 64-pin vqfn (mr), 9x9 mm). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для DSPIC33EP128MU206-I/MR.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DSPIC33EP128MU206-I/MR подходит для 6 применениеs: Digital Power Supplies and PFC, Motor Control (BLDC, PMSM, ACIM), USB Industrial Sensing Nodes, Audio Signal Processing and Codec Interfaces, LED Lighting and Electronic Ballasts, Automated Test and Instrumentation.
Digital Power Supplies and PFC
The DSPIC33EP128MU206-I/MR fits digital power conversion because its 70 MIPS dsPIC33EP core executes single-cycle MAC instructions, sustaining control-loop update rates in the tens of kilohertz needed for buck, boost, and PFC stages. The 12-bit ADC samples voltage and current feedback with the resolution needed for tight regulation, and DMA moves conversion results to RAM without CPU intervention. Firmware-based control enables adaptive compensation, soft-start sequencing, and fault logging that fixed analog controllers cannot offer. USB connectivity adds in-field tuning and firmware update capability. Trade-off: discrete analog controllers have lower latency, so very high switching frequencies may favor hardware PWM-specialized parts, but 128 KB Flash comfortably holds the control firmware plus compensation tables.
Рекомендуется
Motor Control (BLDC, PMSM, ACIM)
The DSPIC33EP128MU206-I/MR supports sensorless and sensored motor drives: the 70 MIPS core runs field-oriented control (FOC) with the DSP engine performing Park/Clarke transforms and PI loops in a fraction of a PWM period, while the 12-bit ADC captures phase currents and bus voltage. High-resolution PWM outputs drive three-phase inverter bridges, and dead-time control is handled in hardware. Sensorless estimators (sliding-mode, back-EMF observers) fit in the 16 KB RAM and 128 KB Flash alongside the main control loop and communication stack. USB enables drive commissioning tools and live tuning. For cost-optimized drives without USB, the pin-compatible DSPIC33EP128MC206-I/MR is an option; MU206 suits drives needing host connectivity or field updates.
Рекомендуется
USB Industrial Sensing Nodes
Industrial condition-monitoring nodes benefit from the DSPIC33EP128MU206-I/MR's combination of USB 2.0 full-speed device support and 12-bit ADC sampling. Vibration, current, and temperature signals are digitized and streamed to a host PC over USB, or buffered in the 16 KB SRAM using DMA for burst captures. The 70 MIPS core can apply DSP filtering (FIR/IIR) before transmission, reducing host-side processing. USB bus power simplifies deployment, while the industrial -40C to +85C rating suits factory-floor enclosures. Compared with an MCU plus separate USB controller, this single-chip approach reduces BOM and board area; the trade-off is a 3.3V-only supply domain, so a small LDO is needed on 5V USB rails.
Рекомендуется
Audio Signal Processing and Codec Interfaces
The DSPIC33EP core's MAC instructions and dual-operand fetch make the DSPIC33EP128MU206-I/MR capable of real-time audio filtering, level detection, and simple effects processing at typical audio sample rates. On the MU206 the USB module supports USB Audio Class device implementations; designers needing a dedicated codec port can instead use the pin-compatible MC206 variant with its DCI module. The 12-bit ADC handles line-level input capture for analysis or control, while 128 KB Flash stores filter coefficient sets and multiple configuration profiles. This suits karaoke systems, PA controllers, and USB audio accessories. For studio-grade 24-bit fidelity, an external audio codec with I2S is recommended, as the internal 12-bit ADC is not hi-fi grade.
Рекомендуется
LED Lighting and Electronic Ballasts
Digitally controlled LED drivers and HID ballasts use the DSPIC33EP128MU206-I/MR to close current loops at 70 MIPS while implementing dimming profiles, thermal derating, and fault protection in firmware. The 12-bit ADC monitors LED current sense and NTC temperature inputs; high-resolution PWM achieves wide dimming ratios without visible flicker. The DSP engine handles average-current-mode compensation efficiently, and 128 KB Flash leaves room for multi-scenario lighting scripts and a bootloader. USB (MU variant) enables field configuration from laptops or service tools, an advantage over fixed-program analog drivers. Boards should keep the ADC sense routing Kelvin-connected to the shunt to preserve the 12-bit converter's accuracy at low currents.
Рекомендуется
Automated Test and Instrumentation
Bench instruments and portable testers leverage the DSPIC33EP128MU206-I/MR for control, DSP post-processing, and USB data connectivity in one 9x9 mm chip. The 70 MIPS core performs stimulus generation, timing control, and Fast Fourier analysis of captured waveforms, while DMA-driven 12-bit ADC sampling acquires analog channels continuously into the 16 KB SRAM. USB full-speed transfers datasets to host software for display and logging, replacing slow UART panels. The 128 KB Flash holds instrument firmware, calibration tables, and self-test routines with headroom for upgrades. Note that for precision metrology, an external 16-24 bit delta-sigma ADC should complement the internal 12-bit converter, which is optimized for control loops rather than laboratory accuracy.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP128MU206-I/MR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP256MU206-I/MR | DSPIC33EP64MU206-I/MR | DSPIC33EP128MU206-H/MR | DSPIC33EP128MC206-I/MR |
|---|---|---|---|---|---|
| Package | 64-VQFN (9x9 mm) | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same | 64-VQFN (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Performance | 70 MIPS, 16-bit | 70 MIPS, 16-bit | 70 MIPS, 16-bit | 70 MIPS, 16-bit | 70 MIPS, 16-bit |
| Program Flash | 128 KB (43K x 24) | 256 KB | 64 KB | 128 KB | 128 KB |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| ADC | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit |
| USB Module | Yes (USB 2.0 FS) | Yes | Yes | Yes | No - DCI instead |
| Temperature Grade | -40C to +85C (I) | -40C to +85C (I) | -40C to +85C (I) | H grade (per distributor listing) | -40C to +85C (I) |
Ключевые отличия
- USB 2.0 full-speed device integrated (против DSPIC33EP128MC206-I/MR)
- 128 KB Flash mid-size memory point (против DSPIC33EP64MU206-I/MR)
- Lowest-cost entry in the MU206 family (против DSPIC33EP256MU206-I/MR)
Заметки по проектированию
The 64-pin VQFN (MR, 9x9 mm) has a central exposed thermal pad that should be soldered to a grounded copper pour with an array of thermal vias - this pad is both the primary heat-removal and ground-return path. Verify the package footprint against the latest Microchip landing-pattern drawing before PCB release; QFN packages are unforgiving of stencil and paste-in-pad mistakes. For rework-friendly prototypes, consider a slight paste reduction on the center pad to minimize voiding and component floating during reflow.
The device operates from a 3.3V supply domain; when powered from USB 5V, use a low-quiescent LDO (e.g., MCP1700 class) with adequate output capacitance. Decouple every VDD pin pair with 0.1 uF ceramics placed within 2 mm of the pins, plus a bulk 10 uF near the regulator output. Budget core-current peaks during 70 MIPS DSP loops and ADC conversions - a shared noisy 3.3V rail with relays or LED drivers will degrade ADC accuracy; isolate the analog supply with a ferrite bead and local filtering.
Peripheral Pin Select (PPS) mapping errors are the most common dsPIC33EP bring-up failure: remappable pins must be locked after configuration, and conflicting mappings can silently disable peripherals. Also verify configuration words (oscillator, watchdog, code protection) before production - the device will not boot at 70 MIPS unless the PLL is correctly configured for the chosen crystal. Test USB enumeration at both full-speed corner voltages (3.0V and 3.6V) early in development.
Информация о соответствии
Compliance status was not stated in the provided distributor snippets; modern Microchip DSPIC33EP parts are typically RoHS-compliant, but verify on the official Microchip product page before procurement.
