DSPIC33EP256MC504T-I/ML - 16-bit 70 MIPS DSC, 256KB Flash | Microchip
Артикул: DSPIC33EP256MC504T-I/ML ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.86 | $4,86 |
| 10 | $4.45 | $44,50 |
| 100 | $4.1 | $410,00 |
| 500 | $3.8 | $1.900,00 |
| 1.000 | $3.55 | $3.550,00 |
DSPIC33EP256MC504T-I/ML Обзор
A digital signal controller combines the compute architecture of a microcontroller with the mathematical acceleration of a DSP. In the power-management hierarchy, the dsPIC33EP sits above general-purpose 8-bit and 16-bit MCUs and directly targets real-time control loops where deterministic interrupt latency and hardware multiply-accumulate operations are mandatory, such as field-oriented control of three-phase motors and digital power conversion.
Key differentiating features of the dsPIC33EP256MC504 include high-speed MCPWM (motor control PWM) modules for complementary or independent PWM generation, quadrature encoder interface (QEI) inputs for rotor position feedback, integrated operational amplifiers and analog comparators that reduce external component count in current-sensing circuits, and DSP engine instructions for filtering and control-law execution. The 60 MHz clock (70 MIPS execution) enables tight control-loop periods typical of digital power supplies and servo drives.
The architecture pairs a 16-bit modified Harvard core with an enhanced interrupt controller and DMA support, keeping deterministic response in safety-relevant loops. On-chip flash self-programming supports field firmware updates, while multiple communication interfaces (UART, SPI, I2C) connect the controller to supervisory systems.
Typical applications include brushless DC and permanent-magnet synchronous motor drives, solar inverters and power-factor-correction stages, digital welding and UPS systems, and industrial HMI/sensor nodes requiring DSP-grade math on a low-cost 16-bit platform.
Design consideration: decouple both VDD/VSS pairs with 0.1 uF ceramics placed directly at the 8x8 QFN pads, and route PWM outputs away from analog op-amp inputs to prevent switching noise coupling into the ADC front end.
This page synthesizes distributor pricing from DigiKey, Mouser, LCSC and Octopart (as of 2026-09-24), drop-in alternatives within the same 44-QFN footprint, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для DSPIC33EP256MC504T-I/ML — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP256MC504T-I/ML (тот же форм-фактор и посадочное место) — отличается по Package.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33EP256MC504T-E/ML
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DSPIC33EP512MC504T-I/ML
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.65 / шт.
Открыть даташит →DSPIC33EP128MC504T-I/ML
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP64MC504T-I/ML
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP256MC504T-H/ML
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP256MC504T-I/ML Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC DSC core |
| Maximum Performance | 70 MIPS |
| CPU Clock Frequency | 60 MHz |
| Program Memory (Flash) | 256 KB (85.5K x 24) |
| RAM | 32 KB |
| Корпус | 44-QFN (8x8 mm) |
| Число выводов | 44 |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40C to +85C (I grade) |
| Peripheral Type | MCPWM (motor control PWM), QEI, OpAmps, Comparators |
| Product Family | dsPIC33EP |
| Packaging | Tape and Reel (T suffix) |
Руководство по цоколевке DSPIC33EP256MC504T-I/ML в корпусе 44-qfn (8x8 mm)
Цоколевка для DSPIC33EP256MC504T-I/ML (корпус 44-qfn (8x8 mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для DSPIC33EP256MC504T-I/ML.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
DSPIC33EP256MC504T-I/ML подходит для 6 применениеs: BLDC/PMSM Motor Drives, Digital Power Conversion (PFC/Solar Inverter), Uninterruptible Power Supplies and Welding Equipment, Industrial Automation and Sensor Nodes, Battery Management and Charging Systems, Embedded Audio and Signal Processing.
BLDC/PMSM Motor Drives
The DSPIC33EP256MC504T-I/ML is purpose-built for brushless DC and permanent-magnet synchronous motor control. Its MCPWM module generates three complementary PWM pairs with hardware dead-time insertion, the QEI inputs decode incremental encoder position, and the on-chip op-amps condition shunt-resistor current measurements ahead of the ADC, enabling full field-oriented control without external analog front-end ICs. At 70 MIPS, the DSP core executes FOC current loops at 10-20 kHz update rates with deterministic interrupt latency. Placing the controller adjacent to the gate drivers with short PWM traces minimizes ringing; the industrial -40C to +85C grade covers most drive-enclosure environments.
Рекомендуется
Digital Power Conversion (PFC/Solar Inverter)
In power-factor-correction stages, LLC converters and solar micro-inverters, the DSPIC33EP256MC504T-I/ML provides the high-speed control loop that analog controllers cannot adapt. The MCPWM outputs drive phase-shifted or interleaved switching stages while ADC-triggered interrupts close voltage and current loops at the PWM frequency. The 70 MIPS DSP engine executes notch filters and feed-forward compensation inline, and the comparators implement fast hardware overcurrent shutdown independent of software. With 256KB flash, multiple control algorithms (burst mode, synchronous rectification, MPPT) coexist and can be field-updated via the self-programming flash. Keep ADC sense routing away from PWM traces to preserve measurement integrity.
Рекомендуется
Uninterruptible Power Supplies and Welding Equipment
UPS inverters and inverter-based welding power sources demand synchronized multi-channel PWM, fast fault response and robust control under load transients - all native strengths of the dsPIC33EP256MC504. The MCPWM module coordinates inverter legs and PFC front ends from one timer domain, ensuring fixed dead time and synchronized ADC sampling. Hardware comparators provide cycle-by-cycle current limiting during short-circuit events that software loops cannot catch. The 32KB RAM supports resonant-controller state buffers and communication stacks simultaneously, and the 256KB flash holds waveform tables for different output profiles selected at runtime. Industrial temperature grading suits the hot interior of these enclosures.
Рекомендуется
Industrial Automation and Sensor Nodes
For factory automation nodes, the DSPIC33EP256MC504T-I/ML combines DSP-grade signal processing with standard serial connectivity. DSP engine instructions (MAC, DSP multiply) run FIR/IIR filters on vibration, load-cell or ultrasonic sensor data at sample rates general-purpose 16-bit MCUs cannot sustain, while UART, SPI and I2C interfaces relay processed results to PLCs or gateways. The 44-QFN 8x8 footprint fits compact distributed I/O boards, and the 70 MIPS core leaves ample margin for protocol handling on top of the DSP workload. Integrated op-amps can amplify bridge-sensor outputs before the ADC, trimming board area and component count in dense installations.
Рекомендуется
Battery Management and Charging Systems
Battery chargers and BMS slave boards use the DSPIC33EP256MC504T-I/ML to execute charge-profile control (CC/CV, temperature-derated curves) with synchronized PWM for the power stage and precise ADC sequencing for cell-voltage multiplexing. The on-chip comparators flag overcurrent and overtemperature conditions in hardware, and the DSP core implements coulomb counting and state-of-charge estimation algorithms in real time. The 256KB flash stores multiple chemistry profiles selectable by an input pin, and flash self-programming logs fault history. The 3.3V supply domain simplifies interfacing with cell-monitoring front ends, while the 44-pin QFN integrates neatly on stacked BMS PCBs.
Рекомендуется
Embedded Audio and Signal Processing
The DSP engine of the DSPIC33EP256MC504T-I/ML (single-cycle MAC, modulo addressing, hardware fractional arithmetic) makes it a cost-effective fixed-point DSP for lightweight audio and sensor-signal processing: active noise cancellation, tone generation, and condition-monitoring spectral analysis. The 70 MIPS throughput supports sample rates of tens of kHz with substantial filter banks, while the 32KB RAM buffers delay lines and coefficient tables. UART/SPI interfaces stream data to codecs or hosts, and the 256KB flash holds firmware plus long coefficient sets. For demanding 24-bit hi-fi paths, a dedicated audio DSP remains preferable, but for control-embedded signal processing this DSC removes a second processor from the BOM.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP256MC504T-I/ML — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP256MC504T-E/ML | DSPIC33EP512MC504T-I/ML | DSPIC33EP128MC504T-I/ML |
|---|---|---|---|---|
| Package | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory (Flash) | 256 KB (85.5K x 24) | 256 KB | 512 KB | 128 KB |
| RAM | 32 KB | 32 KB | 32 KB | 32 KB |
| Performance | 70 MIPS (60 MHz) | 70 MIPS (60 MHz) | 70 MIPS (60 MHz) | 70 MIPS (60 MHz) |
| Temperature Range | -40C to +85C (I grade) | -40C to +125C (E grade) | -40C to +85C (I grade) | -40C to +85C (I grade) |
| Motor Control Peripherals | MCPWM, QEI, OpAmps, Comparators | MCPWM, QEI, OpAmps, Comparators - identical | MCPWM, QEI, OpAmps, Comparators - identical | MCPWM, QEI, OpAmps, Comparators - identical |
Ключевые отличия
- Identical footprint with +125C extended temperature option (против DSPIC33EP256MC504T-E/ML)
- On-chip analog front end reduces BOM cost (против DSPIC33EP128MC504T-I/ML)
- More flash headroom than 64KB-class siblings at identical cost structure (против DSPIC33EP64MC504T-I/ML)
Заметки по проектированию
The 44-QFN (8x8) has an exposed ground paddle that must be soldered to a grounded copper area on the PCB; use a 3x3 via array under the paddle to tie it to inner ground planes for thermal and EMI performance. Because this pad is also the primary heat-removal path for the die, skipping it raises junction temperature significantly in motor-drive applications. Place 0.1 uF decoupling capacitors within 2 mm of each VDD/VSS pin pair and one 4.7-10 uF bulk capacitor near the supply entry.
In motor-control layouts, route the six MCPWM output traces as short, matched groups to the gate drivers and keep them physically separated from the op-amp input (current-sense) traces. Switching edges couple capacitively into high-impedance analog nodes and corrupt ADC readings used for FOC current loops. Use a local analog ground island under the op-amp/ADC pins, connect it to digital ground at a single point, and add a small RC filter (e.g., 1 kOhm + 1 nF) on sense inputs where bandwidth allows.
Do not leave MCLR floating: the ICSP programming and debug interface (MCLR/PGD/PGC) must be broken out to a header even in production units, or field firmware updates via flash self-programming become impossible without desoldering the device. Also confirm the correct suffix before ordering - the T (tape and reel), -I (industrial -40C to +85C) and /ML (44-QFN) codes define packaging and temperature grade; mixing -I and -E parts in one assembly line requires separate reflow lots since the -E grade carries a different qualification.
Информация о соответствии
Compliance status not stated in the retrieved web data; modern Microchip dsPIC33EP production parts are typically RoHS-compliant, but verify on the official Microchip product page before release.