DSPIC33FJ64MC204T-I/PT - 16-bit 40 MIPS DSC 64KB Flash | Microchip
Артикул: DSPIC33FJ64MC204T-I/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.39 | $6,39 |
| 10 | $5.79 | $57,90 |
| 25 | $5.32 | $133,00 |
| 100 | $4.86 | $486,00 |
| 1.000 | $4.31 | $4.310,00 |
DSPIC33FJ64MC204T-I/PT Обзор
A digital signal controller combines the computational throughput of a digital signal processor with the deterministic interrupt architecture and peripherals of a microcontroller. In the embedded hierarchy, the DSC sits between a general-purpose MCU and a full DSP, making it the preferred choice for closed-loop control loops that must execute fast, repetitive math such as PID regulators, field-oriented motor control, and digital power conversion. The dsPIC33F family is pin compatible with the PIC24HJ family and shares a high degree of compatibility with the dsPIC30F family, enabling seamless migration paths across PIC24F, dsPIC30F and dsPIC33F devices.
Key features include the 16-bit modified Harvard architecture core running at 40 MIPS from an internal PLL, 64 KB of self-programmable FLASH with 1000 erase/write cycles, a DMA controller that offloads data movement between peripherals and RAM, and a 6-channel Motor Control PWM with dead-time insertion. A high-speed 10-bit/12-bit ADC with multiple sample-and-hold circuits synchronized to the PWM enables precise current sensing in motor drive loops. Communication is covered by dual UART, SPI, and I2C modules.
Technically, the DSP engine provides single-cycle MAC, 40-bit wide accumulators, and hardware modulo and bit-reversed addressing, while the interrupt controller supports up to 63 interrupt vectors with programmable priority levels. The internal fast RC oscillator with PLL reduces external BOM cost, though a primary crystal remains an option for precision timing.
Typical applications include three-phase BLDC/PMSM motor drives, solar and battery inverters, digital SMPS and power-factor-correction stages, and industrial sensor signal conditioning.
When designing, budget the 3.3 V rail carefully and add a 10 uF plus 0.1 uF decoupling pair on each VDD pin; the VCAP pin requires its specified bulk capacitor for the internal regulator to start reliably.
This page synthesizes distributor pricing, same-footprint drop-in alternatives, pinout data, and practical design notes not consolidated in the manufacturer datasheet.
Аналоги без доработки для DSPIC33FJ64MC204T-I/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33FJ64MC204T-I/PT (тот же форм-фактор и посадочное место) — отличается по Core Architecture, Package, RoHS Status, Supply Voltage, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33FJ64MC204-I/PT
✅ Прямая замена✓ В наличии
$4.75 / шт.
Открыть даташит →DSPIC33FJ32MC304-E/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.45 / шт.
Открыть даташит →DSPIC33FJ64GP204T-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.1 / шт.
Открыть даташит →DSPIC33FJ32GP204-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.78 / шт.
Открыть даташит →DSPIC33FJ32GP204-E/PT
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.15 / шт.
Открыть даташит →DSPIC33FJ64MC204T-I/PT Максимальные параметры и электрические характеристики
| Core Architecture | 16-bit dsPIC33F modified Harvard |
| Max CPU Speed | 40 MIPS (40 MHz) |
| Program Memory | 64 KB (64K x 8) FLASH |
| DMA Controller | Yes |
| Напряжение питания | 3.0 V to 3.6 V |
| I/O Ports | 21 |
| Корпус | 44-TQFP (10 x 10 mm), PT suffix |
| Тип монтажа | Surface Mount |
| ROM Type | Flash |
| Motor Control PWM | Yes (dedicated MCPWM module) |
| Рабочая температура | -40C to +85C (I grade) |
| Series | dsPIC33FJ64MC |
| Family Compatibility | Pin compatible with PIC24HJ; highly compatible with dsPIC30F |
| Packing | Tape and Reel (T suffix) |
| Статус RoHS | Lead-free, RoHS compliant |
| Статус жизненного цикла | Active |
| Communication Interfaces | UART, SPI, I2C |
Конфигурация выводов DSPIC33FJ64MC204T-I/PT
| Контакт 1 | MCLR — Master clear reset input, active low |
| Контакт 2 | RB0/AN0/VREF+/CN2 — Port B I/O, ADC channel 0, positive voltage reference |
| Контакт 3 | RB1/AN1/VREF-/CN3 — Port B I/O, ADC channel 1, negative voltage reference |
| Контакт 4 | RB2/AN2/SS1/CN4 — Port B I/O, ADC channel 2, SPI slave select |
| Контакт 5 | RB3/AN3/INDX/CN5 — Port B I/O, ADC channel 3, encoder index input |
| Контакт 6 | RB4/AN4/QEA/IC7/CN6 — Port B I/O, ADC channel 4, encoder QEA, capture 7 |
| Контакт 7 | RB5/AN5/QEB/IC8/CN7 — Port B I/O, ADC channel 5, encoder QEB, capture 8 |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1/CLKI/CN30/RA2 — Oscillator crystal input or external clock input |
| Контакт 10 | OSC2/CLKO/CN29/RC15 — Oscillator crystal output or clock output |
| Контакт 11 | SOSCI/CN1/RC13 — Secondary oscillator input, Timer1 clock |
| Контакт 12 | SOSCO/CN0/RC14 — Secondary oscillator output, Timer1 clock |
| Контакт 13 | VDD — Positive supply, 3.0 V to 3.6 V |
| Контакт 14 | RB6/PGEC — Port B I/O, programming clock |
| Контакт 15 | RB7/PGED — Port B I/O, programming data |
| Контакт 16 | VDD — Positive supply, 3.0 V to 3.6 V |
| Контакт 17 | RC1/T2CK/IC1 — Port C I/O, Timer2 clock, input capture 1 |
| Контакт 18 | RC2/T3CK/IC2 — Port C I/O, Timer3 clock, input capture 2 |
| Контакт 19 | RC3/T5CK/IC3 — Port C I/O, Timer5 clock, input capture 3 |
| Контакт 20 | VCAP — Internal regulator bulk capacitor connection |
| Контакт 21 | RC4/SDI1/SCL — Port C I/O, SPI data in, I2C clock |
| Контакт 22 | RC5/SDO1/SDA — Port C I/O, SPI data out, I2C data |
| Контакт 23 | VSS — Ground reference |
| Контакт 24 | RC6/U1RX/SDI2 — Port C I/O, UART1 receive, SPI2 data in |
| Контакт 25 | RC7/U1TX/SDO2 — Port C I/O, UART1 transmit, SPI2 data out |
| Контакт 26 | RC8/SCK2 — Port C I/O, SPI2 clock |
| Контакт 27 | RC9/SS2 — Port C I/O, SPI2 slave select |
| Контакт 28 | VDD — Positive supply, 3.0 V to 3.6 V |
| Контакт 29 | AVDD — Analog supply for ADC |
| Контакт 30 | AVSS — Analog ground for ADC |
| Контакт 31 | RB8/IC7 — Port B I/O, input capture 7 |
| Контакт 32 | RB9/IC8 — Port B I/O, input capture 8 |
| Контакт 33 | RB10/OC4 — Port B I/O, output compare 4 |
| Контакт 34 | RB11/OC5 — Port B I/O, output compare 5 |
| Контакт 35 | RB12/PWM1L — Port B I/O, Motor PWM 1 low-side output |
| Контакт 36 | RB13/PWM1H — Port B I/O, Motor PWM 1 high-side output |
| Контакт 37 | RB14/PWM2L — Port B I/O, Motor PWM 2 low-side output |
| Контакт 38 | RB15/PWM2H — Port B I/O, Motor PWM 2 high-side output |
| Контакт 39 | RA0/T1CK — Port A I/O, Timer1 external clock |
| Контакт 40 | RA1/OCFA — Port A I/O, PWM fault A input |
| Контакт 41 | RA2/U2RX — Port A I/O, UART2 receive |
| Контакт 42 | RA3/RTCC — Port A I/O, real-time clock calibration |
| Контакт 43 | RA4/OCFB — Port A I/O, PWM fault B input |
| Контакт 44 | VSS — Ground reference |
Типичное применение
DSPIC33FJ64MC204T-I/PT подходит для 6 применениеs: Three-Phase BLDC/PMSM Motor Drives, Digital Switch-Mode Power Supplies and PFC, Industrial Automation and Sensor Conditioning, Automotive and E-Mobility Auxiliary Control, Battery Management and Portable Power Systems, Audio Signal Processing and Effects.
Three-Phase BLDC/PMSM Motor Drives
The DSPIC33FJ64MC204T-I/PT is purpose-built for field-oriented control of BLDC and PMSM motors: its dedicated Motor Control PWM module generates six complementary outputs with programmable dead-time and fault shutdown, while the high-speed ADC is PWM-triggered to sample phase currents at exactly the same point of every switching cycle, eliminating ripple-induced measurement error. The 40 MIPS DSP engine with single-cycle MAC executes the FOC current and speed loops with deterministic latency, and the DMA controller streams ADC results to RAM without CPU intervention, freeing MIPS for the speed loop and communication. Typical power stages use this DSC with a three-phase gate driver such as the MCP802x or IR2136 family.
Рекомендуется
Digital Switch-Mode Power Supplies and PFC
In digital SMPS and power-factor-correction stages, the DSPIC33FJ64MC204T-I/PT closes fast voltage and current loops at switching frequencies of 100 kHz to several hundred kHz. The PWM module supports complementary outputs with dead-time for half-bridge and synchronous topologies, ADC conversion can be triggered at mid-PWM-cycle to sample inductor current away from switching noise, and the DSP engine's single-cycle MAC implements proportional-integral compensators with minimal cycle count. The DMA controller moves sampled data autonomously, keeping loop jitter in the nanosecond range. Its 3.3 V I/O interfaces cleanly with isolated feedback devices, making it a strong fit for telecom rectifiers, solar micro-inverters, and LLC converters.
Рекомендуется
Industrial Automation and Sensor Conditioning
For industrial control nodes, the DSPIC33FJ64MC204T-I/PT combines a 40 MIPS 16-bit core with UART, SPI, and I2C ports to bridge analog front ends and field buses. The on-chip ADC with multiple sample-and-hold circuits digitizes sensor channels synchronized to timers for coherent sampling, while the DMA controller buffers data streams with zero CPU overhead. Flash self-programming allows field firmware updates over UART, and the internal fast RC oscillator with PLL supports clock-redundant designs. Typical deployments include weigh scales, flow meters, PLC I/O modules, and vibration-monitoring nodes, where the DSP instructions accelerate FFT-based condition-monitoring algorithms without an external DSP.
Рекомендуется
Automotive and E-Mobility Auxiliary Control
Although the I temperature grade is -40C to +85C, the DSPIC33FJ64MC204T-I/PT serves non-powertrain automotive functions such as window lift, pump control, HVAC blower drives, and actuator positioning. The Motor Control PWM module with dead-time insertion drives H-bridges and three-phase stages for these auxiliary motors, while the ADC samples current for stall detection and diagnostic coverage. The E-grade sibling DSPIC33FJ64MC204T-E/PT extends operation to -40C to +125C for under-hood positions using the same firmware. The deterministic interrupt architecture and hardware DSP engine give predictable loop timing that software-timed solutions on general MCUs cannot guarantee.
Рекомендуется
Battery Management and Portable Power Systems
Battery chargers and BMS units benefit from the DSPIC33FJ64MC204T-I/PT's combination of synchronous buck PWM control, multi-channel ADC for cell-voltage and current monitoring, and UART/I2C for host communication. The DMA controller services ADC scan sequences automatically, so cell voltages are sampled on a precise timer schedule independent of firmware load, while the DSP engine computes coulomb counting and state-of-charge filters efficiently. Its 3.0 V to 3.6 V single-supply operation and internal oscillator simplify bias design in compact chargers for power tools, e-bikes, and UPS modules. Flash self-write enables logging of fault and usage history in non-volatile memory without external EEPROM.
Рекомендуется
Audio Signal Processing and Effects
The dsPIC33F DSP engine - 40 MIPS, single-cycle MAC, dual 40-bit accumulators, and bit-reversed addressing - makes the DSPIC33FJ64MC204T-I/PT a practical host for real-time audio effects, active crossovers, and speech-band processing. ADC sampling synchronized via timer interrupts feeds block-based FIR and IIR filters whose multiply-accumulate loops execute at full core rate, and the DCI (Data Converter Interface) peripheral connects directly to audio codecs over a standard I2S-like frame. With 64 KB of FLASH there is headroom for filter coefficient tables plus a communication stack, and UART-based MIDI or host control integrates easily into effects pedals, mixers, and install-audio controllers.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33FJ64MC204T-I/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33FJ64MC204-I/PT | DSPIC33FJ32MC304-E/PT | DSPIC33FJ64GP204T-I/PT | DSPIC33FJ32GP204-I/PT |
|---|---|---|---|---|---|
| Package | 44-TQFP (10x10 mm), PT | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Speed | 40 MIPS (16-bit) | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS |
| Program FLASH | 64 KB | 64 KB | 32 KB | 64 KB | 32 KB |
| Motor Control PWM | Yes | Yes | Yes | No (GP variant) | No (GP variant) |
| DMA | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature | -40C to +85C (I) | -40C to +85C | -40C to +125C (E) | -40C to +85C | -40C to +85C |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Packing | Tape & Reel (T) | Tray | Tray (non-T) | Tape & Reel | Tray (non-T) |
Ключевые отличия
- Dedicated Motor Control PWM module (против DSPIC33FJ64GP204T-I/PT)
- Double the program memory (против DSPIC33FJ32MC304-E/PT)
- Tape-and-reel production packing (против DSPIC33FJ64MC204-I/PT)
Заметки по проектированию
Decouple every VDD pin (13, 16, 28) with a 0.1 uF ceramic capacitor placed within 3-5 mm of the pin, plus one bulk 10 uF capacitor per supply rail. The VCAP pin (20) requires the bulk capacitor specified in the datasheet for the internal 1.8 V core regulator - omitting or undersizing it is the most common cause of failure to start and erratic brown-out behavior on dsPIC33FJ designs. Keep AVDD (29) filtered separately through an LC or RC network from the digital 3.3 V rail for best ADC accuracy.
When driving a three-phase inverter from the Motor Control PWM outputs, route PWM1H/PWM1L pairs away from the analog inputs (RB0-RB5/AN0-AN5) and the AVDD/AVSS corner to prevent switching noise coupling into current-sense samples. Trigger the ADC at mid-PWM off-time (center-aligned trigger) so sampling occurs when the bridge is in a defined state; this practice, documented in Microchip's motor-control application notes, can reduce current-measurement error from tens of counts to a few LSBs.
Configure the configuration words (FOSC, FWDT, FICD) correctly at first flash - a wrong oscillator setting with PLL can lock the device into a non-bootable state requiring MCLR-controlled recovery. Reserve RB6/RB7 (PGEC/PGED, pins 14-15) for In-Circuit Serial Programming; do not load them heavily during programming sessions. Also verify code fits the 64 KB FLASH with growth margin: if the application will expand, migrate to the 128 KB family members or the pin-compatible PIC24HJ parts instead of filling this device to its limit.
Информация о соответствии
Per digchip specification listing, the package is lead-free plastic. RoHS compliance per distributor listings. AEC-Q100 not claimed for the I grade; the E grade targets extended temperature but AEC-Q100 qualification is not documented in the provided data.
