EP910LI-35T - 24-Macrocell Classic EPLD 35ns 44-PLCC | Intel
Артикул: EP910LI-35T ⚠ Последняя закупка| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $43.21 | $43,21 |
| 10 | $39.85 | $398,50 |
| 100 | $35.4 | $3.540,00 |
| 500 | $31.2 | $15.600,00 |
| 1.000 | $28.5 | $28.500,00 |
EP910LI-35T Обзор
An EPLD (Erasable Programmable Logic Device) is a non-volatile programmable logic IC historically used as a glue-logic replacement for multiple TTL/CMOS SSI/MSI parts. Sitting in the taxonomy between PAL/GAL and modern CPLD/FPGA, EPLDs offer deterministic combinational and registered logic with EPROM- or EEPROM-based configuration. The EP910 family from Intel/Altera represents one of the industry-standard Classic EPLD lines used in long-life-cycle industrial, military, and aerospace systems.
Key features include 24 macrocells with configurable I/O architecture, 450 usable gates, 35 ns tPD propagation delay, 28.6 MHz fMAX toggle frequency, and a single 5 V (4.75 V–5.25 V) supply. The device supports in-system programmability via Altera's classic programming algorithm and offers 10-year data retention thanks to EPROM-based configuration cells. The 44-pin PLCC package is JEDEC-standard and supports both socketed and surface-mount assembly.
The EP910LI-35T architecture combines a global interconnect matrix with per-macrocell product-term arrays, allowing wide AND-OR logic and buried register feedback. Compared with discrete TTL/MSI replacement, it reduces board area by typically 5:1 to 10:1 while improving timing predictability and reducing power consumption to CMOS levels at idle.
Typical applications include industrial control glue logic, military/aerospace retrofit boards, telecom interface adapters, and legacy peripheral controllers. The wide supply tolerance (4.75 V–5.25 V) makes it tolerant of legacy 5 V backplanes. The deterministic 35 ns delay simplifies worst-case timing closure in asynchronous control paths.
Designers should note that the EP910 family is in long-term support status - new designs are not recommended, but Obsolescence/EOL notifications typically allow multi-year last-time-buy windows via franchised distributors and aftermarket suppliers like Rochester Electronics. Programming requires Altera-supported hardware (e.g., Altera Logic Programmer or compatible).
This page synthesizes verified distributor pricing, drop-in replacement options (including the EP910LC and EP910ILC family variants), and practical design considerations not consolidated in the original datasheet.
Аналоги без доработки для EP910LI-35T — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с EP910LI-35T (тот же форм-фактор и посадочное место) — отличается по Package, Technology, Mounting Type, Operating Temperature, Propagation Delay (tPD).
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
EP910LI-35
✅ Прямая замена✓ В наличии
$25.8 / шт.
Открыть даташит →EP910LC-35T
✅ Прямая замена✓ В наличии
$28.9 / шт.
Открыть даташит →EP910LC-30T
✅ Прямая замена✓ В наличии
$7.1 / шт.
Открыть даташит →EP910ILC-25
✅ Прямая замена✓ В наличии
$9.95 / шт.
Открыть даташит →EP910ILC-15
✅ Прямая замена✓ В наличии
$16.1 / шт.
Открыть даташит →EP910LI-30T
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$64.59 / шт.
Открыть даташит →EP910LI-35T Максимальные параметры и электрические характеристики
| Family | Classic EPLD (EP910) |
| Logic Elements | 24 macrocells |
| Usable Gates | 450 |
| Propagation Delay (tPD) | 35 ns |
| Maximum Toggle Frequency (fMAX) | 28.6 MHz |
| Supply Voltage (VCC) | 5 V (4.75 V to 5.25 V) |
| Technology | CMOS, EPROM-based |
| Корпус | 44-pin PLCC (JEDEC) |
| Рабочая температура | -40C to +85C (industrial, 'I' suffix) |
| Тип монтажа | Surface Mount / Socket |
| Programming Method | EPROM (UV-erasable for windowed versions) |
Конфигурация выводов EP910LI-35T
| Контакт 1 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 2 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 3 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 4 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 5 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 6 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 7 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 8 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 9 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 10 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 11 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 12 | GND — Ground |
| Контакт 13 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 14 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 15 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 16 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 17 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 18 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 19 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 20 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 21 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 22 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 23 | GND — Ground |
| Контакт 24 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 25 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 26 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 27 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 28 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 29 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 30 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 31 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 32 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 33 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 34 | GND — Ground |
| Контакт 35 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 36 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 37 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 38 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 39 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 40 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 41 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 42 | I/O — Bidirectional I/O pin (macrocell) |
| Контакт 43 | VCC — +5 V power supply |
| Контакт 44 | VCC — +5 V power supply |
Типичное применение
EP910LI-35T подходит для 6 применениеs: Industrial Control Glue Logic, Military and Aerospace Retrofit Boards, Telecom Interface Adapters, Legacy Peripheral Controllers, Test and Measurement Instrumentation, Point-of-Sale and Retail Terminal Logic.
Industrial Control Glue Logic
The EP910LI-35T fits industrial control glue-logic applications because its 24 macrocells and 450 usable gates consolidate 5-10 standard 74-series TTL/MSI parts into a single non-volatile device, while the industrial temperature range (-40C to +85C) supports factory-floor PLC backplanes. The 35 ns tPD provides deterministic timing for asynchronous control paths in motor drives and conveyor controllers. The 5 V supply and TTL-compatible I/O allow direct drop-in replacement of legacy GAL/PAL devices on existing PCB footprints. Compared with discrete TTL logic, the EP910LI-35T reduces board area by approximately 5:1 to 10:1 while lowering idle power to CMOS levels.
Рекомендуется
Military and Aerospace Retrofit Boards
The EP910LI-35T is widely deployed in military and aerospace retrofit programs where its non-volatile EPROM configuration ensures instant-on behavior without external boot memory - critical for avionics and weapons-system interfaces. The industrial temperature range (-40C to +85C) and CMOS technology provide long-term reliability in vibration and thermal-cycling environments. The 35 ns tPD handles legacy MIL-STD-1553 and ARINC 429 interface timing without issues. Rochester Electronics' franchised long-term supply program supports multi-decade aerospace platform lifecycles. The 44-pin PLCC package accommodates conformal coating and ruggedization processes required by DO-160 and MIL-STD-810 environments.
Рекомендуется
Telecom Interface Adapters
The EP910LI-35T serves telecom interface adapters (T1/E1, RS-232/RS-485 glue logic, legacy PBX line cards) where its 24 macrocells handle protocol conversion and timing-recovery functions with deterministic 35 ns latency. The 5 V supply matches legacy telecom backplanes, and the 44-pin PLCC allows socketed field replacement - critical for service-depot maintenance. The non-volatile configuration eliminates in-system programming at power-up, supporting hot-swap and field-service workflows. The wide 4.75 V to 5.25 V supply tolerance handles voltage droop during line-card power events. Compared with modern CPLDs, the EP910LI-35T's 28.6 MHz fMAX is sufficient for sub-30 MHz telecom interface rates including ISDN BRI and H.110 bus compatibility.
Рекомендуется
Legacy Peripheral Controllers
The EP910LI-35T integrates ISA-bus peripheral controllers (parallel ports, SCSI adapters, floppy controllers) on legacy motherboards, where its 24 macrocells implement address decoding, wait-state generation, and interrupt prioritization. The 35 ns tPD supports ISA bus timing (8 MHz) without inserting wait states. The 5 V TTL-compatible I/O interfaces directly to ISA bus drivers without level translation. The 44-pin PLCC allows socketed upgrades for firmware revisions via EPROM erasure and reprogramming. Designers can consolidate 6-12 standard PAL/GAL devices into one EP910LI-35T, reducing motherboard BOM and improving reliability.
Рекомендуется
Test and Measurement Instrumentation
The EP910LI-35T fits test and measurement front-end logic (signal routing matrices, scan-chain controllers, custom waveform generators) because its deterministic 35 ns timing simplifies worst-case timing closure in instrumentation paths where PXI/VXI backplane timing is critical. The industrial temperature range supports lab-to-field deployment without redesign. The non-volatile EPROM configuration ensures repeatable test sequences without boot delays. The 24 macrocells handle 4-8 channels of multiplexed signal routing with per-channel enable logic. Compared with modern FPGAs, the EP910LI-35T offers instant-on deterministic behavior with no configuration bitstream validation overhead.
Рекомендуется
Point-of-Sale and Retail Terminal Logic
The EP910LI-35T serves point-of-sale terminals, barcode scanners, and receipt printers where its 24 macrocells consolidate I/O decoding, keypad scanning, and display-driving logic in a single 5 V device. The 35 ns tPD handles real-time keypad debounce and LCD multiplexing without timing issues. The non-volatile EPROM configuration supports firmware updates via windowed packages (ceramic versions) for service depot reprogramming. The industrial temperature range accommodates outdoor kiosk and refrigerated-cooler deployments. The 44-pin PLCC footprint supports socketed field replacement, minimizing service downtime. Compared with discrete CMOS logic, the EP910LI-35T reduces PCB area by 50-70% in cost-sensitive retail terminals.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для EP910LI-35T — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | EP910LI-35 | EP910LC-35T | EP910LC-30T | EP910ILC-25 | EP910ILC-15 | EP910LI-30T |
|---|---|---|---|---|---|---|---|
| Package | 44-pin PLCC | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same |
| Brand | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) | Intel (Altera) |
| Macrocells | 24 | 24 | 24 | 24 | 24 | 24 | 24 |
| Usable Gates | 450 | 450 | 450 | 450 | 450 | 450 | 450 |
| Propagation Delay (tPD) | 35 ns | 35 ns | 35 ns | 30 ns | 25 ns | 15 ns | 30 ns |
| Supply Voltage | 5 V (4.75-5.25 V) | 5 V (4.75-5.25 V) | 5 V (4.75-5.25 V) | 5 V (4.75-5.25 V) | 5 V (4.75-5.25 V) | 5 V (4.75-5.25 V) | 5 V (4.75-5.25 V) |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C (industrial) | 0C to +70C (commercial) | 0C to +70C (commercial) | 0C to +70C (commercial) | 0C to +70C (commercial) | -40C to +85C (industrial) |
| Packaging | Tape & Reel | Tube / Tray | Tape & Reel | Tape & Reel | Tube / Tray | Tube / Tray | Tape & Reel |
Ключевые отличия
- Industrial temperature grade for harsh environments (против EP910LC-35T)
- Tape and Reel packaging for high-volume assembly (против EP910LI-35)
- Standard 35 ns speed grade for broad application fit (против EP910ILC-15)
Заметки по проектированию
The EP910LI-35T operates from a single 5 V supply (4.75 V to 5.25 V). Decouple VCC with at least one 0.1 uF ceramic capacitor placed within 5 mm of each VCC pin (pins 43 and 44). Add a bulk 10 uF tantalum or aluminum electrolytic capacitor on the 5 V rail near the device to handle transient current during simultaneous output switching. Idle CMOS current consumption is typically 1-5 mA, but dynamic current during high-frequency operation can reach 50-100 mA depending on output loading. Use a regulated linear supply rather than a switching regulator to avoid injecting noise into the EP910's analog-sensitive I/O cells.
The 44-pin PLCC package uses JEDEC-standard surface-mount land pattern with 1.27 mm pin pitch. For socketed deployment, use a low-profile PLCC-44 through-hole socket (e.g., Aries 44-650-10 or equivalent) to enable field replacement without rework. All four GND pins (12, 23, 34) must be connected to a low-impedance ground plane; missing even one GND connection can cause intermittent logic errors due to ground bounce during simultaneous I/O switching. Keep high-speed traces (above 10 MHz) short and routed over a continuous ground plane to minimize EMI and crosstalk.
Do NOT attempt to program the EP910LI-35T with MAX+PLUS II quartus-generated files - the EP910 family uses the legacy programming algorithm (pre-MAX series). Use Altera MAX+PLUS II 10.x or earlier with the appropriate EP910 device support file. Verify programming voltage and timing per the Classic Device Family datasheet - incorrect programming parameters can permanently damage the EPROM cells. For windowed ceramic packages, expose to UV eraser for 20-30 minutes (per datasheet) before reprogramming. Do not exceed maximum I/O source/sink current ratings (typically 4-8 mA per pin) or total package dissipation.
Estimated: At 28.6 MHz fMAX with 12 simultaneously-switching outputs into 50 pF loads, dynamic power dissipation is approximately P = C x V^2 x f x N = 50e-12 x 25 x 28.6e6 x 12 = 429 mW. With PLCC-44 theta_JA of approximately 50 C/W (still air), junction temperature rise is about 21 C above ambient. This is well within the industrial -40C to +85C range, but the design should provide at least 100 mm^2 of copper pour connected to the GND pins to improve thermal dissipation and reduce ground bounce. No external heatsink is required for typical operation.
All I/O pins on the EP910LI-35T are bidirectional with TTL-compatible thresholds (VIL = 0.8 V, VIH = 2.0 V). Unused I/O pins must be programmed as outputs driving LOW or HIGH to avoid floating-input oscillation. For inputs, add a 10 kohm pull-up resistor to VCC to define the default state during power-up before the EPROM is read. Avoid long unterminated traces on clock or high-speed signals - use series damping resistors (22-33 ohm) near the driver if trace length exceeds 50 mm. The 35 ns tPD provides sufficient margin for legacy 8 MHz/16 MHz bus interfaces without additional wait states.
Информация о соответствии
Compliance status for EP910LI-35T not verified in available data - consult Rochester Electronics or Intel PSG product lifecycle documents. Not applicable for AEC-Q100 (logic device without automotive qualification); industrial temperature grade is available via 'LI' suffix but is not equivalent to AEC-Q100 automotive qualification.
