INA223AIDSKT - 26V Current Sense Amplifier & Power Monitor | TI
Артикул: INA223AIDSKT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $3.75 | $3,75 |
| 10 | $3.42 | $34,20 |
| 100 | $3.06 | $306,00 |
| 500 | $2.78 | $1.390,00 |
| 1.000 | $2.51 | $2.510,00 |
INA223AIDSKT Обзор
A current sense amplifier (also called a current shunt monitor) is a specialized precision amplifier that converts the small differential voltage developed across a shunt resistor into a ground-referenced, scalable output signal. Within the power management hierarchy, it sits in the current and power monitoring layer between raw voltage regulators and system controllers, enabling battery management, fault protection, and energy telemetry without a dedicated ADC front end.
Key features include a wide common-mode input range of up to 26V that is independent of the supply voltage, a programmable gain architecture that lets designers trade shunt value against full-scale range, and bidirectional sensing that supports both charge and discharge current measurement. The analog voltage output and power-monitor function can be read by a simple ADC channel or comparator, minimizing system cost and software complexity.
Technically, the INA223 uses a zero-drift architecture that suppresses offset and offset drift over time and temperature, which is essential for accurate low-side and high-side sensing across the automotive and industrial temperature span. The high/low-side capability means the same design can be reused above or below the shunt, simplifying platform designs across 3.3V, 5V, 12V, and 24V rails within the 26V limit.
Typical applications include battery-powered systems current and power telemetry, server and telecom -48V/negative-rail-adjacent monitoring within ratings, motor drive DC bus supervision, and power-supply health monitoring in industrial equipment. The analog output interfaces directly to microcontroller ADC inputs such as TI MSP430 or C2000 devices.
Design consideration: choose the shunt resistor so maximum expected current produces an output swing comfortably inside the ADC range; excessive shunt value wastes power and degrades accuracy through self-heating.
This page synthesizes distributor pricing, drop-in same-family gain alternatives, and practical design guidance not consolidated in the manufacturer datasheet.
Аналоги без доработки для INA223AIDSKT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с INA223AIDSKT (тот же форм-фактор и посадочное место) — отличается по Architecture, Output Type, Package, Product Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
INA223AIDSKR
✅ Прямая замена✓ В наличии
$0.94 / шт.
Открыть даташит →INA223A1IDSKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
INA223A2IDSKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
INA223A3IDSKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
INA223A4IDSKR
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
INA223AIDSKT Максимальные параметры и электрические характеристики
| Product Type | Current Sense Amplifier / Analog Power Monitor |
| Common-Mode Voltage Range | 0 V to 26 V |
| Gain Configuration | Programmable-gain |
| Measurement Type | High-Side / Low-Side, Bidirectional |
| Architecture | Zero-Drift |
| Тип выхода | Analog voltage output |
| Рабочая температура | -40C to +105C |
| Корпус | 10-SON / WSON (DSK) 2.5 mm x 2.5 mm |
| Тип монтажа | Surface Mount |
| Число выводов | 10 |
| Статус RoHS | Compliant |
Руководство по цоколевке INA223AIDSKT в корпусе 10-son / wson (dsk) 2.5 mm x 2.5 mm
Цоколевка для INA223AIDSKT (корпус 10-son / wson (dsk) 2.5 mm x 2.5 mm). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для INA223AIDSKT.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
INA223AIDSKT подходит для 6 применениеs: Battery Current & Power Monitoring, 24V Industrial Rail Supervision, Server & Telecom Power Telemetry, Motor Drive DC Bus Monitoring, Power Supply Health & Efficiency Monitoring, IoT & Smart Device Energy Metering.
Battery Current & Power Monitoring
The INA223AIDSKT fits battery-powered systems because its bidirectional high/low-side sensing tracks both charge and discharge current across a 0V to 26V common-mode range that covers most single-cell stacks and 24V lead-acid or multi-cell lithium packs. Placed across a low-side shunt with the reference pin biased at mid-scale, the analog output swings above and below reference for current direction, feeding a single MCU ADC channel. The zero-drift architecture keeps offset error negligible across the wide shunt signal range typical of batteries, and the integrated analog power monitor provides instantaneous power for state-of-charge and state-of-health algorithms without extra computation.
Рекомендуется
24V Industrial Rail Supervision
Industrial 24V buses sit comfortably inside the 26V common-mode rating, so the INA223AIDSKT monitors motor drives, PLC I/O channels, and factory automation loads while being powered itself from a 3.3V or 5V logic supply - the common-mode range is independent of supply. The amplifier is placed high-side with a milliohm-class shunt; the analog power-monitor output scales with current, giving controllers a single-signal health indicator for overload and brownout detection. The zero-drift topology maintains accuracy across the -40C to +105C industrial temperature range, and the small 2.5 mm x 2.5 mm WSON footprint fits crowded I/O boards.
Рекомендуется
Server & Telecom Power Telemetry
Data center and telecom equipment require continuous power telemetry on dense power distribution boards. The INA223AIDSKT suits this role because the analog output and power monitor can be multiplexed into existing ADC channels without adding an I2C bus segment, and the 26V common-mode range covers 12V server rails, 24V intermediate buses, and -48V-adjacent monitoring topologies within ratings. The zero-drift input stage preserves low-percentage accuracy at light loads where server sleep-state currents are small relative to full load. Its tiny WSON-10 package enables one monitor per rail on high-density PDUs, and the programmable-gain family lets one shunt serve multiple current ranges across product variants.
Рекомендуется
Motor Drive DC Bus Monitoring
In motor drives, the DC bus current and instantaneous power indicate mechanical load and fault conditions. The INA223AIDSKT monitors the bus via a high-side shunt with 0V to 26V common mode - suitable for 12V and 24V drive platforms - while its analog power output gives a load-proportional signal for closed-loop torque estimation and stall detection. Zero-drift accuracy prevents offset-induced false trips at idle, and the bidirectional capability captures regenerative braking current flowing back into the bus. Response on the analog output is fast enough for comparator-based overcurrent latching when paired with a fast reference, complementing slower telemetry ADC sampling.
Рекомендуется
Power Supply Health & Efficiency Monitoring
AC-DC and DC-DC power supplies increasingly include real-time efficiency telemetry. The INA223AIDSKT measures input or output current with a compact shunt; because current and power are output as scaled analog voltages, a single ADC capture yields instantaneous power for computing efficiency against an input voltage measurement. The 26V common-mode ceiling covers 12V, 19V, and 24V rails, and the zero-drift architecture keeps light-load readings meaningful, which is where efficiency curves degrade first. The tiny 10-SON package fits inside enclosed adapters and open-frame supplies without significant layout penalty, enabling adaptive power management in the host system.
Рекомендуется
IoT & Smart Device Energy Metering
Battery and mains-powered IoT nodes benefit from knowing their own consumption profile. The INA223AIDSKT's low component count - one shunt, one IC, a reference voltage - and the 2.5 mm x 2.5 mm WSON-10 footprint make per-device energy metering practical in space-constrained smart home products. The analog output connects directly to low-cost MCU ADC pins, and the power monitor output can trigger wake-up when load power exceeds a threshold, supporting energy harvesting and duty-cycling strategies. Its -40C to +105C rating allows outdoor sensor installations, and the 26V common-mode range accommodates solar-charged 12V and 24V battery nodes.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для INA223AIDSKT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | INA223AIDSKR | INA223A1IDSKR | INA223A2IDSKR |
|---|---|---|---|---|
| Package | 10-SON / WSON (DSK) 2.5x2.5 | 10-SON / WSON (DSK) 2.5x2.5 - same | 10-SON / WSON (DSK) 2.5x2.5 - same | 10-SON / WSON (DSK) 2.5x2.5 - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Common-Mode Voltage | 0 V to 26 V | 0 V to 26 V | 0 V to 26 V | 0 V to 26 V |
| Gain Configuration | Programmable-gain | Programmable-gain | Fixed gain (A1) | Fixed gain (A2) |
| Measurement Type | High/Low-side, bidirectional | High/Low-side, bidirectional | High/Low-side, bidirectional | High/Low-side, bidirectional |
| Architecture | Zero-drift | Zero-drift | Zero-drift | Zero-drift |
| Output | Analog voltage + power monitor | Analog voltage + power monitor | Analog voltage + power monitor | Analog voltage + power monitor |
Ключевые отличия
- Analog power monitor output on top of current output (против INA210 series shunt monitors)
- Programmable-gain flexibility within one footprint (против INA223A1IDSKR (fixed-gain A1 variant))
- 26V common-mode independent of supply (против Generic low-side current sense amps)
Заметки по проектированию
Use Kelvin (4-wire) connections from the shunt resistor to the INA223AIDSKT sense inputs: route dedicated traces from the shunt pads directly to the amplifier inputs rather than tapping the main current path. Parasitic resistance in shared traces adds gain error, and parasitic inductance in long sense lines causes ringing during load transients. Keep sense traces short and matched. Place 100 nF decoupling close to the supply pin and the 10-SON exposed pad must be soldered to a grounded copper pour for thermal and electrical performance per the TI datasheet layout section.
Select the shunt for 50-100 mV full-scale drop at maximum load current. Estimated: a 10 mOhm shunt at 5 A dissipates I2R = 0.25 W, requiring at least a 1206 or shunt-rated resistor to limit self-heating drift; a 5 mOhm shunt halves dissipation but doubles offset-referred error, which the zero-drift architecture mitigates. With the programmable-gain INA223, prefer a smaller shunt with higher gain over a large shunt with low gain, unless small-signal resolution is the binding constraint.
Do not exceed 26V common-mode on the sense inputs even transiently - inductive spikes on motor or battery cables during switching can exceed the absolute maximum and damage the part; add a small RC filter or TVS on the sense lines in high-di/dt environments. Also verify that the reference pin bias voltage keeps the analog output within the ADC input range for both current polarities, and confirm the Q1 (automotive) suffix separately if AEC-Q100 compliance is required for your build.
Информация о соответствии
RoHS compliance standard for current TI production; AEC-Q100 status applies to separate INA223 Q1 ordering variants - verify on TI quality portal for this exact suffix.
