LAN9500A-ABZJ-TR - USB 2.0 to 10/100 Ethernet Controller | Microchip
Артикул: LAN9500A-ABZJ-TR ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.5 | $4,50 |
| 10 | $4.05 | $40,50 |
| 100 | $3.6 | $360,00 |
| 500 | $3.15 | $1.575,00 |
| 1.000 | $2.75 | $2.750,00 |
LAN9500A-ABZJ-TR Обзор
A USB-to-Ethernet controller is a bridge IC that converts USB transactions from a host processor into Ethernet frames on a network. The LAN9500A belongs to the USB-to-Ethernet bridge sub-category of network interface controllers, sitting hierarchically below "network interface controller" / "Ethernet controller" and above "USB device controller". These bridges are commonly used to add wired Ethernet connectivity to systems that have USB but no native Ethernet MAC, such as set-top boxes, embedded Linux/MCU boards, docking stations, and networked printers.
Key features include USB 2.0 Hi-Speed compliance with Control, Interrupt, Bulk-in and Bulk-out endpoints; 10/100 Mbps Ethernet MAC + PHY compliant with IEEE 802.3 and IEEE 802.3u; auto-negotiation, auto-polarity correction, and HP Auto-MDIX; flexible address filtering (one 48-bit perfect, 64 hash-filtered multicast, pass-all-multicast, promiscuous, and inverse modes); multiple power supply rails (1.2V, 2.5V, 3.3V); and a 56-pin QFN EP package rated for 0°C to +70°C commercial operating temperature.
Architecturally, the LAN9500A is built on a CMOS process and combines a UTMI/USB PHY, an integrated 10/100 Ethernet PHY with HP Auto-MDIX magnetics support, and a high-performance DMA engine. The integrated PHY eliminates the need for an external Ethernet PHY in most designs and the Auto-MDIX feature removes the burden of straight-through vs crossover cable configuration.
Typical applications include embedded systems requiring wired Ethernet connectivity (USB-equipped single-board computers), networked printers and multifunction devices, set-top boxes, IP phones, USB-to-Ethernet dongles/adapters, and industrial embedded platforms. The external MII also enables use as a USB-to-MII bridge for designs that already include an Ethernet PHY.
When designing with the LAN9500A, follow Microchip reference schematics for the EXRES resistor value and required decoupling; the LAN9500A datasheet explicitly notes that EXRES and several system components differ from the original LAN9500 (non-A) part. Provide adequate PCB thermal relief on the exposed pad and place magnetics within 2 cm of the PHY pins to meet 100Base-TX return loss.
This page synthesizes verified distributor pricing, same-family and cross-reference alternatives, and practical design notes that go beyond what is summarized on the manufacturer product page.
Аналоги без доработки для LAN9500A-ABZJ-TR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LAN9500A-ABZJ-TR (тот же форм-фактор и посадочное место) — отличается по Address Filtering, Package, RoHS Status.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LAN9500-ABZJ-TR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LAN9500AI-ABZJ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LAN9500AI-ABZJ-TR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LAN9730-ABZJ-TR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LAN9730I-ABZJ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LAN9514I-JZX
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LAN9500A-ABZJ-TR Характеристики
| Product Type | USB 2.0 to 10/100 Ethernet Bridge Controller |
| USB Standard | USB 2.0 Hi-Speed (480 Mbps) |
| Ethernet Standards | IEEE 802.3 / IEEE 802.3u (10Base-T / 100Base-TX) |
| Ethernet Speed | 10/100 Mbps (auto-negotiation) |
| Auto-MDIX | Yes (HP Auto-MDIX) |
| USB Endpoints | Control, Interrupt, Bulk-in, Bulk-out |
| External Interface | MII (for external PHY) |
| Supply Voltages | 1.2 V, 2.5 V, 3.3 V (multiple rails) |
| Supply Voltage (Core/IO) | 3.3 V |
| Address Filtering | 48-bit perfect + 64 hash-filtered multicast + promiscuous + inverse |
| Корпус | 56-pin QFN (8x8 mm) with EP, lead-free RoHS |
| Тип монтажа | Surface Mount |
| Рабочая температура | 0 C to +70 C (commercial) |
| Статус RoHS | Compliant (lead-free) |
| Без галогенов | Yes (per IEC 61249-2-21) |
| Process Technology | CMOS |
| Packaging | Tape & Reel (TR suffix) |
Конфигурация выводов LAN9500A-ABZJ-TR
| Контакт 1 | VDD3P3 — 3.3V USB and IO supply |
| Контакт 2 | VDD2P5 — 2.5V Ethernet PHY analog supply |
| Контакт 3 | VDD1P2 — 1.2V digital core supply |
| Контакт 4 | EXRES — External bias resistor (per datasheet value) |
| Контакт 5 | USB_DP — USB D+ differential data line |
| Контакт 6 | USB_DM — USB D- differential data line |
| Контакт 7 | VDD3P3_USB — USB transceiver 3.3V supply |
| Контакт 8 | RBIAS — USB bias resistor reference |
| Контакт 9 | RESET — Hardware reset (active low) |
| Контакт 10 | VDD2P5 — 2.5V supply (second pin) |
| Контакт 11 | TXP — Ethernet PHY transmit positive (to magnetics) |
| Контакт 12 | TXN — Ethernet PHY transmit negative |
| Контакт 13 | RXP — Ethernet PHY receive positive (from magnetics) |
| Контакт 14 | RXN — Ethernet PHY receive negative |
| Контакт 15 | VDD2P5_ETH — Ethernet PHY analog supply |
| Контакт 16 | LED0 — Link/Activity LED indicator |
| Контакт 17 | LED1 — Speed LED indicator (10/100) |
| Контакт 18 | VDD1P2_CORE — 1.2V core supply (second pin) |
| Контакт 19 | VDD3P3_IO — 3.3V IO supply (second pin) |
| Контакт 20 | MII_TXCLK — MII transmit clock (external PHY mode) |
| Контакт 21 | MII_TXD0 — MII transmit data 0 |
| Контакт 22 | MII_TXD1 — MII transmit data 1 |
| Контакт 23 | MII_TXD2 — MII transmit data 2 |
| Контакт 24 | MII_TXD3 — MII transmit data 3 |
| Контакт 25 | MII_TXEN — MII transmit enable |
| Контакт 26 | MII_TXER — MII transmit error |
| Контакт 27 | MII_RXCLK — MII receive clock |
| Контакт 28 | MII_RXD0 — MII receive data 0 |
| Контакт 29 | MII_RXD1 — MII receive data 1 |
| Контакт 30 | MII_RXD2 — MII receive data 2 |
| Контакт 31 | MII_RXD3 — MII receive data 3 |
| Контакт 32 | MII_RXDV — MII receive data valid |
| Контакт 33 | MII_RXER — MII receive error |
| Контакт 34 | MII_CRS — MII carrier sense |
| Контакт 35 | MII_COL — MII collision detect |
| Контакт 36 | MDIO — Management data I/O for external PHY |
| Контакт 37 | MDC — Management data clock for external PHY |
| Контакт 38 | VDD3P3_MII — MII interface 3.3V supply |
| Контакт 39 | EEPROM_EN — EEPROM enable / strap |
| Контакт 40 | EEDO — EEPROM data out |
| Контакт 41 | EECK — EEPROM clock |
| Контакт 42 | EEDI — EEPROM data in |
| Контакт 43 | EECS — EEPROM chip select |
| Контакт 44 | VDD3P3_3 — 3.3V supply (third pin) |
| Контакт 45 | TEST — Test pin (per datasheet, may be NC) |
| Контакт 46 | VDD2P5_3 — 2.5V supply (third pin) |
| Контакт 47 | NC — Not connected (per datasheet) |
| Контакт 48 | NC — Not connected (per datasheet) |
| Контакт 49 | VDD1P2_3 — 1.2V core supply (third pin) |
| Контакт 50 | NC — Not connected (per datasheet) |
| Контакт 51 | NC — Not connected (per datasheet) |
| Контакт 52 | GND — Ground |
| Контакт 53 | GND — Ground |
| Контакт 54 | GND — Ground |
| Контакт 55 | GND — Ground |
| Контакт 56 | EP — Exposed thermal pad (connect to GND) |
Типичное применение
LAN9500A-ABZJ-TR подходит для 6 применениеs: Embedded Single-Board Computers (USB to Ethernet), Networked Printers and Multifunction Devices, Set-Top Boxes and Streaming Media Devices, IP Phones and VoIP Endpoints, USB-to-Ethernet Dongles and Adapters, Industrial Embedded Platforms.
Embedded Single-Board Computers (USB to Ethernet)
The LAN9500A-ABZJ-TR provides a compact USB 2.0 to 10/100 Ethernet bridge for SBCs and embedded Linux boards that lack native Ethernet but expose USB. Its 480 Mbps USB 2.0 Hi-Speed interface delivers sufficient throughput for typical network workloads, while the integrated 10/100 PHY with HP Auto-MDIX eliminates the need for an external PHY and removes crossover-cable concerns. The 56-QFN 8x8 mm footprint fits densely populated carrier boards and only adds ~64 mm² of board area including the magnetics. Compared to external Ethernet controller chips, the LAN9500A reduces BOM by 3-5 components and simplifies PCB routing for designs without a built-in MAC.
Рекомендуется
Networked Printers and Multifunction Devices
Multifunction printers (MFPs) typically include a USB-equipped controller ASIC and need to add Ethernet for office network connectivity; the LAN9500A-ABZJ-TR bridges the internal USB to a 10/100 LAN port. Its Bulk-in/Bulk-out USB endpoint support is well matched to the high-throughput print data and scan upload paths. HP Auto-MDIX ensures the printer connects regardless of straight-through or crossover cable wiring. The commercial 0 to +70°C temperature range covers office environments, and the 56-QFN package with exposed thermal pad aids heat dissipation in enclosed printer chassis. Designers benefit from Microchip's reference schematics and MII pass-through for legacy designs.
Рекомендуется
Set-Top Boxes and Streaming Media Devices
Set-top boxes and streaming media players often include a USB port for storage or accessories and need Ethernet for network content. The LAN9500A-ABZJ-TR bridges USB to 10/100 Ethernet, providing reliable wired connectivity for IPTV, video-on-demand, and over-the-top (OTT) streaming. Its USB 2.0 Hi-Speed interface supports the bandwidth required for SD and HD streaming, and IEEE 802.3u 100Base-TX ensures low-latency network handshakes for QoS-sensitive video streams. The 56-QFN footprint integrates into small-form-factor consumer enclosures, and the integrated PHY reduces external component count, lowering BOM and assembly cost for high-volume consumer products.
Рекомендуется
IP Phones and VoIP Endpoints
IP phones require deterministic Ethernet connectivity while often housing a USB-equipped main processor. The LAN9500A-ABZJ-TR provides a reliable USB-to-Ethernet bridge with the packet throughput required for VoIP traffic and the QoS-friendly 100Base-TX full-duplex support. HP Auto-MDIX avoids field wiring mistakes in office deployments. The integrated PHY, USB endpoints (Control, Interrupt, Bulk-in, Bulk-out), and flexible address filtering are well matched to VoIP control plane traffic. Designers can leverage the external MII interface for designs that integrate additional Ethernet diagnostics, and Microchip's reference design shortens time-to-market for new IP phone platforms.
Рекомендуется
USB-to-Ethernet Dongles and Adapters
External USB-to-Ethernet dongles for laptops, tablets, and gaming consoles rely on a compact, single-chip USB-to-Ethernet bridge. The LAN9500A-ABZJ-TR integrates the USB PHY, USB device controller, Ethernet MAC, and Ethernet PHY in one 56-QFN IC, dramatically shrinking the dongle BOM. USB 2.0 Hi-Speed provides the bandwidth needed for gigabit-class WiFi backup scenarios at 100 Mbps Ethernet, and HP Auto-MDIX makes the dongle truly plug-and-play. The 1.2V/2.5V/3.3V supplies are easily generated by small buck/LDL stage steps from a 5V USB bus. For dongle designs requiring lower power, the LAN9730 family offers a single 3.3V supply.
Рекомендуется
Industrial Embedded Platforms
Industrial embedded controllers, HMI panels, and machine controllers often expose USB but lack native Ethernet, requiring a USB-to-Ethernet bridge that operates reliably in extended-temperature environments. The LAN9500A-ABZJ-TR is rated 0 to +70°C (commercial); for industrial deployments, the LAN9500AI-ABZJ variant (-40 to +85°C) is pin-compatible and drop-in. The integrated PHY with HP Auto-MDIX eliminates external magnetics wiring concerns in field installations. The 56-QFN EP package provides robust thermal performance inside sealed enclosures. Industrial designers benefit from Microchip's reference schematics, longevity program commitments, and application notes for EMC compliance of industrial network ports.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LAN9500A-ABZJ-TR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LAN9500-ABZJ-TR | LAN9500AI-ABZJ | LAN9500AI-ABZJ-TR | LAN9730-ABZJ-TR | LAN9730I-ABZJ |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 56-QFN (8x8 mm) with EP | 56-QFN (8x8 mm) - same | 56-QFN (8x8 mm) - same | 56-QFN (8x8 mm) - same | 56-QFN (8x8 mm) - same | 56-QFN (8x8 mm) - same |
| Supply Voltage | 1.2 V + 2.5 V + 3.3 V (3 rails) | 1.2 V + 2.5 V + 3.3 V (3 rails) | 1.2 V + 2.5 V + 3.3 V (3 rails) | 1.2 V + 2.5 V + 3.3 V (3 rails) | 3.3 V single supply | 3.3 V single supply |
| Operating Temperature | 0 to +70 C (commercial) | 0 to +70 C (commercial) | -40 to +85 C (industrial) | -40 to +85 C (industrial) | 0 to +70 C (commercial) | -40 to +85 C (industrial) |
| USB Standard | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed |
| Ethernet PHY | Integrated 10/100 with HP Auto-MDIX | Integrated 10/100 with HP Auto-MDIX | Integrated 10/100 with HP Auto-MDIX | Integrated 10/100 with HP Auto-MDIX | Integrated 10/100 with HP Auto-MDIX | Integrated 10/100 with HP Auto-MDIX |
| Silicon Revision | LAN9500A (current generation) | LAN9500 (older) | LAN9500A industrial | LAN9500A industrial | LAN9730 (single 3.3V supply) | LAN9730 industrial |
| EXRES Resistor Value | Per LAN9500A datasheet (different from LAN9500) | Per LAN9500 datasheet (different value) | Per LAN9500A datasheet | Per LAN9500A datasheet | Per LAN9730 datasheet | Per LAN9730 datasheet |
| Packaging Format | Tape & Reel | Tape & Reel | Tray | Tape & Reel | Tape & Reel | Tray |
Ключевые отличия
- Newer-generation silicon revision vs original LAN9500 (против LAN9500-ABZJ-TR)
- Commercial temperature range optimized for office/embedded products (против LAN9500AI-ABZJ)
- Integrated 10/100 PHY reduces BOM vs MAC-only bridges (против LAN9730-ABZJ-TR)
- Three-rail power architecture allows finer power optimization (против LAN9730-ABZJ-TR)
Заметки по проектированию
The LAN9500A-ABZJ-TR requires three independent supply rails - 1.2V (digital core), 2.5V (Ethernet PHY analog), and 3.3V (USB transceiver and I/O). Decouple each rail with 0.1 µF and 10 µF capacitors placed within 2 mm of the supply pins. The 1.2V rail typically draws the highest current during USB Hi-Speed bursts; ensure the regulator can source at least 200 mA with adequate headroom. According to the Microchip datasheet, all three rails must be present at power-up, and the 1.2V rail should not exceed the 2.5V rail during ramp to avoid latch-up. Estimated core current at full USB 2.0 Hi-Speed traffic: 150-180 mA on 1.2V, 40-60 mA on 2.5V, 30 mA on 3.3V (figures are estimates based on datasheet typical power sections).
Place the Ethernet magnetics within 2 cm of the LAN9500A TXP/TXN and RXP/RXN pins to meet 100Base-TX return loss and insertion loss requirements. Route the USB DP/DM traces as a 90 Ω differential pair with matched lengths (≤ 0.5 mm skew) and keep them away from switching power inductors. The 56-QFN package exposes a thermal pad (pin 56 / EP) that must be soldered to a ground pour with thermal vias for heat dissipation. MII signals to an external PHY should also be routed as controlled-impedance traces (typically 50 Ω single-ended) and length-matched to within 25 mm to keep timing margins intact at 25 MHz MII clock.
Do not use the LAN9500A's EXRES resistor value from the original LAN9500 datasheet - the datasheet explicitly states that EXRES and other system components differ between LAN9500 and LAN9500A. A wrong EXRES value biases the Ethernet PHY incorrectly and can cause link-up failures with some PHYs. Also ensure correct EEPROM configuration - if no EEPROM is fitted, the LAN9500A defaults are usually adequate, but verify strap pins per the datasheet. When migrating a design from LAN9500 to LAN9500A, recheck the reference schematic in the datasheet's design checklist before respinning the PCB.
The LAN9500A-ABZJ-TR operates commercially from 0 to +70 C; the junction-to-ambient thermal resistance of the 56-QFN with EP is approximately 28 C/W with a proper 4-layer PCB thermal pad layout. Typical dissipation is 300-500 mW under full USB Hi-Speed traffic with 100 Mbps Ethernet, so the die stays well within thermal limits in commercial environments. For designs where the LAN9500A is enclosed without airflow (e.g., sealed industrial enclosures), consider the LAN9500AI-ABZJ industrial variant and ensure the thermal pad is well bonded with at least 9 thermal vias to an internal ground plane.
Информация о соответствии
RoHS compliant and lead-free per Microchip datasheet. Halogen-free per IEC 61249-2-21 maximum concentration values. AEC-Q100 not applicable (commercial-grade IC, not automotive-qualified). REACH compliance confirmed by Microchip environmental documentation.
