LM2902D - Quad 26V 1.2MHz Op Amp | Texas Instruments
Артикул: LM2902D ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
LM2902D Обзор
An operational amplifier is a voltage-gain amplifier that uses negative feedback to control gain, bandwidth, input impedance, and output behavior. The quad LM2902 combines four amplifiers in one integrated circuit, reducing board area compared with four separate single or dual amplifier packages. Its general-purpose architecture belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchy and is widely used where inexpensive, robust signal conditioning is more important than precision or high speed.
Key characteristics include four independent amplifier channels, push-pull output capability, a 1.2 MHz typical gain-bandwidth product, and 2 mV typical offset voltage. The 26 V maximum supply rating provides compatibility with common industrial voltage ranges. According to the Texas Instruments LM2902 product page, the device is a quad, 26 V, 1.2 MHz, 2 mV-offset operational amplifier. The distributor listing identifies the LM2902D orderable package as 14-SOIC.
The internal architecture is frequency compensated and intended to operate from a single supply or split supply over a wide voltage range. Each amplifier can be used independently, while the common package provides four channels for instrumentation, sensor interfaces, active filters, voltage followers, and signal-conditioning blocks. The device should be selected against the complete input/output voltage, common-mode range, output-current, noise, and thermal requirements of the target circuit.
Typical applications include industrial measurement, transducer interfaces, audio and control circuits, low-frequency active filters, sensor amplifiers, and general-purpose analog signal conditioning. Because it is a general-purpose amplifier, the LM2902D is most appropriate when system cost, supply tolerance, and availability matter more than very low offset, rail-to-rail operation, or high-frequency precision.
The primary design consideration is supply and signal-range verification. Confirm that every input and output remains within the device's specified operating limits under load, temperature, and supply variation. Decoupling capacitors should be placed close to the supply pins, and each amplifier channel requires appropriate feedback and biasing. PCB creepage, grounding, output loading, and decoupling should be checked during layout.
This page combines verified manufacturer and distributor information, drop-in replacement guidance, package comparison data, and practical design notes to help engineers evaluate the LM2902D for new designs and service replacements.
Аналоги без доработки для LM2902D — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM2902D (тот же форм-фактор и посадочное место) — отличается по Package, Gain-Bandwidth Product, Operating Temperature Range, RoHS Status.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LM2902DT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM2902M
✅ Прямая замена✓ В наличии
$0.0527 / шт.
Открыть даташит →LM324DT
✅ Прямая замена✓ В наличии
$0.0827 / шт.
Открыть даташит →LM2902DR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM2902DT
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM2902D Максимальные параметры и электрические характеристики
| Product Type | Quad operational amplifier |
| Number of Amplifier Channels | 4 |
| Maximum Supply Voltage | 26 V |
| Typical Gain-Bandwidth Product | 1.2 MHz |
| Typical Input Offset Voltage | 2 mV |
| Supply Configuration | Single supply or split supply |
| Тип выхода | Push-pull |
| Корпус | 14-SOIC |
| Тип монтажа | Surface mount |
| Supplier Description | Standard general-purpose amplifier |
| Статус RoHS | unknown |
| REACH Status | unknown |
Руководство по цоколевке LM2902D в корпусе 14-soic
Цоколевка для LM2902D (корпус 14-soic). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для LM2902D.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
LM2902D подходит для 6 применениеs: Industrial Sensor Signal Conditioning, Low-Frequency Active Filters, Audio Control and Amplifier Front Ends, Voltage Buffering and Signal Isolation, Power-Supply Monitoring and Control Loops, Test and Measurement Signal Conditioning.
Industrial Sensor Signal Conditioning
The LM2902D fits industrial sensor-conditioning circuits that need several amplified stages within one package. Its four independent channels can support sensor input buffering, gain stages, offset handling, and output conditioning without requiring four separate amplifier packages. The 1.2 MHz typical gain-bandwidth product is suitable for many low-frequency industrial signals, while the 26 V supply rating accommodates common industrial supply contexts. The design must still verify the actual sensor range against the amplifier's input common-mode and output-swing limits, and it should include filtering or gain selection appropriate to the sensor bandwidth.
Рекомендуется
Low-Frequency Active Filters
The LM2902D is appropriate for low-frequency active-filter implementations where four amplifier sections can be used for cascaded stages or parallel filtering paths. Its 1.2 MHz typical gain-bandwidth product provides more bandwidth than many precision low-frequency filter applications require, while the internal frequency compensation supports practical feedback-based designs. Component tolerances, noise, slew behavior, and output loading determine the achievable filter response. Designers should derive R and C values from the desired cutoff and validate the final response with the actual source and load impedances rather than relying only on ideal equations.
Рекомендуется
Audio Control and Amplifier Front Ends
The LM2902D can serve in audio control, mixing, and low-frequency preamplifier circuits where four channels provide useful flexibility for level control and signal routing. The 26 V maximum supply rating and push-pull output description make it relevant to general-purpose analog signal chains, although the exact output-current and distortion limits must be checked before driving a load. The 1.2 MHz bandwidth is more than adequate for many audio-band control functions but does not by itself establish high-fidelity power-amplifier performance. Use appropriate input coupling, biasing, feedback, and output protection for the selected audio topology.
Рекомендуется
Voltage Buffering and Signal Isolation
Each LM2902D channel can be configured as a unity-gain voltage follower to buffer a source from the next circuit stage. Four independent channels make the package useful when several control, measurement, or interface nodes require buffering. The device's 2 mV typical input offset voltage and 1.2 MHz typical gain-bandwidth product are concrete starting points, but actual buffer accuracy depends on input bias current, output loading, supply voltage, temperature, and the selected feedback configuration. Check source and sink current requirements carefully because the verified data does not provide the complete output-current specification.
Рекомендуется
Power-Supply Monitoring and Control Loops
The LM2902D can implement comparator-like or control-loop signal conditioning in industrial power systems, provided the monitored signal remains inside the amplifier's valid input and output ranges. Four channels allow reference buffering, error amplification, and output-interface conditioning in a compact arrangement. The 26 V supply rating is relevant to higher-voltage systems, but the complete operating limits, input bias behavior, and output drive must be verified in the manufacturer datasheet. Protection, startup sequencing, and fault-state behavior should be designed around the actual power-supply topology rather than inferred from the generic amplifier description.
Рекомендуется
Test and Measurement Signal Conditioning
The LM2902D is usable in general-purpose test and measurement front ends for amplifying, scaling, and buffering low-frequency signals. Four channels allow multiple measurement paths to share one package, reducing board area compared with separate single amplifiers. The device's 1.2 MHz typical gain-bandwidth product is suitable for many low-bandwidth measurement functions, but precision instrumentation may require lower offset, lower noise, or tighter common-mode limits than the verified data provides. Validate input impedance, settling behavior, noise, and calibration stability in the complete measurement system before using it for laboratory or production-test requirements.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM2902D — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM2902DT | LM2902M | LM324D | LM2902DR | LM2902DT |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments | STMicroelectronics |
Ключевые отличия
- Four independent amplifier channels in one package (против LM324D)
- 26 V family supply rating (против LM2902DT)
- 1.2 MHz typical gain-bandwidth product (против LM324D)
Заметки по проектированию
Place the supply bypass capacitor as close as practical to the LM2902D supply pins, and keep the return path short and low-impedance. The supplied data confirms a 14-SOIC package but does not specify pin numbers, so use the official Texas Instruments pinout before laying out the board. Keep sensitive input and feedback traces away from switching nodes, high-current outputs, and inductor coupling paths.
Do not assume that a quad amplifier can be replaced by any LM324 or LM2902-family part solely because the package name is similar. The verified search results identify LM2902D, LM2902DT, LM2902M, LM324D, and LM2902DR as comparison candidates, but they do not provide complete pinout, temperature, offset, bandwidth, common-mode, and output-current data. Verify the exact manufacturer datasheet before substituting a part into production.
Use short, direct feedback routes and avoid adding unnecessary capacitance at amplifier inputs. The LM2902D's 1.2 MHz typical gain-bandwidth product is suitable for many low-frequency signal-conditioning paths, but high-impedance nodes can be sensitive to parasitic capacitance and bias-current errors. Confirm source impedance, load impedance, and stability requirements in the final topology.
Check input and output signal limits separately from the 26 V supply rating. The supply rating describes the device family, not permission to place arbitrary input or output voltages on the pins. Bias single-supply signals within the specified common-mode range and verify output swing under the worst-case load and supply condition before enabling the circuit.
Информация о соответствии
The supplied verified product snippets do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Compliance must be confirmed from current manufacturer documentation.
