LMT84LPM - 1.5V Analog Temperature Sensor TO-92 | TI
Артикул: LMT84LPM ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0.62 | $0,62 |
| 10 | $0.52 | $5,20 |
| 100 | $0.39 | $39,00 |
| 500 | $0.32 | $160,00 |
| 1.000 | $0.27 | $270,00 |
LMT84LPM Обзор
An analog output temperature sensor is a type of temperature sensor IC (part of the broader sensor and semiconductor hierarchy) that converts measured die temperature directly into a proportional voltage, which a microcontroller ADC can read without digital bus configuration. Unlike thermistors, analog sensors provide a linear, calibrated transfer function; unlike digital sensors such as the TMP117, they require no I2C/SMBus protocol stack.
Key features include 1.5V-capable single-supply operation, 10 uA-class current consumption for effective power-cycling in battery-powered designs, a Class-AB push-pull output capable of sourcing and sinking heavy loads, 0.7 ms power-on time, and typical accuracy of plus or minus 0.4C (plus or minus 2.7C maximum) per the TI LMT84 datasheet.
Architecturally, the LMT84 uses a CMOS bandgap-derived temperature-dependent voltage with an output stage that maintains linearity across the full -50C to +150C range while drawing micropower supply current, enabling years of operation from a small lithium cell.
Typical applications include battery-powered environmental monitoring, HVAC thermal sensing, portable medical devices, automotive sub-systems (via the AEC-Q100 qualified LMT84-Q1 variant), and appliance over-temperature detection.
Design tip: because output gain is negative (-5.5 mV/C), invert the transfer function in firmware; add a 0.1 uF bypass capacitor close to the supply pin for stable ADC readings.
Аналоги без доработки для LMT84LPM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LMT84-Q1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LMT85
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM94022
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TMP235
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TMP36
⚡ Тот же корпус ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LMT84LPM Максимальные параметры и электрические характеристики
| Тип датчика | Analog output local temperature sensor |
| Тип выхода | Analog voltage (Class-AB push-pull) |
| Temperature Sensitivity | -5.5 mV/C |
| Measuring Range | -50C to +150C |
| Accuracy (typical) | +/-0.4C |
| Accuracy (maximum) | +/-2.7C |
| Supply Voltage (min) | 1.5 V |
| Ток покоя | 5.4 uA |
| Power-On Time | 0.7 ms |
| Корпус | TO-92-3 (LPM) |
| Тип монтажа | Through Hole |
| Рабочая температура | -50C to +150C |
| Output Structure | Push-pull (strong source and sink capability) |
| Статус RoHS | Compliant |
| Automotive Variant | LMT84-Q1 (AEC-Q100 Grade 0) |
Конфигурация выводов LMT84LPM
| Контакт 1 | GND — Ground reference |
| Контакт 2 | VTEMP — Analog temperature output (-5.5 mV/C) |
| Контакт 3 | VDD — Supply input (1.5V min) |
Типичное применение
LMT84LPM подходит для 6 применениеs: Battery-Powered Environmental Monitoring, HVAC and Thermostat Sensing, Automotive Thermal Monitoring, Portable Medical Devices, Appliance Over-Temperature Protection, IoT Sensor Nodes and Smart Home.
Battery-Powered Environmental Monitoring
The LMT84 fits battery-powered sensors because its 1.5V minimum supply and 5.4 uA quiescent current allow direct connection to a lithium coin cell without a boost converter. With 0.7 ms power-on time, designers can duty-cycle the sensor, sampling temperature in sub-millisecond windows and shutting down between readings, reducing average consumption far below 1 uA. The Class-AB output drives a microcontroller ADC input directly. This combination supports multi-year battery life in wireless environmental loggers.
Рекомендуется
HVAC and Thermostat Sensing
In HVAC systems, room and duct temperatures from -20C to +60C sit well inside the LMT84's -50C to +150C range. The linear -5.5 mV/C transfer function gives roughly 30 mV per 5C change, adequate resolution for a 10-bit ADC, while +/-0.4C typical accuracy is comparable to NTC thermistor solutions without divider resistors or lookup tables. Because it replaces thermistor divider networks, the LMT84 simplifies BOM and calibration while the push-pull output tolerates long wiring runs to the controller board.
Рекомендуется
Automotive Thermal Monitoring
For automotive programs, the LMT84-Q1 variant is AEC-Q100 Grade 0 qualified on an automotive grade flow, covering -40C to +150C ambient conditions found in cabin, body, and under-hood-adjacent modules. Its 1.5V-capable micropower operation suits always-on body electronics monitored from low-voltage rails, and the analog output can feed either an MCU ADC or a window comparator for fault detection. Using the Q1 part removes qualification risk in ISO 26262-relevant monitoring paths.
Рекомендуется
Portable Medical Devices
Portable medical devices such as thermometers and wearable monitors benefit from the LMT84's low-voltage, low-current operation: 5.4 uA quiescent draw and 1.5V supply operation preserve coin-cell life in body-temperature probes. The +/-0.4C typical accuracy is sufficient for consumer health monitoring, and 0.7 ms power-on time enables instant-on readings for patient-facing devices. The analog output simplifies firmware compared to I2C digital sensors, shortening development cycles for cost-sensitive medical consumables.
Рекомендуется
Appliance Over-Temperature Protection
White goods and appliances require robust over-temperature supervision near motors, heaters, and power supplies. The LMT84's +150C upper range covers most appliance hot spots, and its push-pull output can directly drive a comparator for a hard trip signal without firmware dependence. Because the output is linear and monotonic, a simple resistor divider can set a warning threshold while the MCU reads graded temperature for derating logic. The 5.4 uA consumption keeps protection circuits negligible on standby power budgets.
Рекомендуется
IoT Sensor Nodes and Smart Home
Smart-home IoT endpoints (door sensors, climate pucks, leak detectors) rely on the LMT84 for ambient temperature with minimal energy cost. Its analog interface eliminates I2C address conflicts in multi-sensor nodes, and the micropower supply current plus 0.7 ms wake time pairs naturally with duty-cycled wireless MCUs. With a -5.5 mV/C gain, a 10-bit ADC referenced at 1.8V resolves about 0.6C steps, adequate for comfort-level reporting, while costing a fraction of digital sensor alternatives.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LMT84LPM — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LMT84-Q1 | LMT85 | LM94022 | TMP235 |
|---|---|---|---|---|---|
| Package | TO-92-3 (LPM) | TO-92-3 / SC70-5 - same pinout | TO-92 / SC70 - similar pinout | similar pinout per TI compare tool | similar pinout per TI compare tool |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Output Gain | -5.5 mV/C fixed | -5.5 mV/C fixed | selectable -13.6/-10.9/-8.2/-5.5 mV/C | pin-selectable gain | different average sensor gain |
| Typical Accuracy | +/-0.4C | +/-0.4C | comparable accuracy | comparable accuracy | comparable accuracy |
Ключевые отличия
- Lowest-voltage operation in the LMT8x family (против LMT85)
- Simplicity vs selectable-gain parts (против LM94022)
- Micropower duty-cycling (против TMP36)
Заметки по проектированию
Place a 0.1 uF ceramic bypass capacitor directly across VDD and GND of the LMT84. For the TO-92 LPM package, keep lead lengths short so the die tracks the ambient/board temperature rather than self-heating. If sensing air temperature, orient the TO-92 body away from heat sources and allow airflow; thermal mass of the package adds response lag of several seconds.
Because quiescent current is only 5.4 uA and power-on time is 0.7 ms, duty-cycling the sensor supply (via a GPIO-driven load switch or MCU pin) yields dramatic energy savings in battery designs. After power-up, allow the output to settle per the datasheet power-on specification before sampling the ADC; sampling too early returns an invalid voltage.
The LMT84 gain is negative (-5.5 mV/C): voltage decreases as temperature rises, which trips up firmware ported from TMP36-style positive-gain sensors. Use the datasheet transfer function/lookup table rather than a single-point calibration. Also ensure the ADC input impedance or sampling capacitor does not load the push-pull output beyond its rated drive, and never exceed the datasheet maximum supply voltage.
Информация о соответствии
RoHS compliance per TI product page. Automotive qualification applies to the LMT84-Q1 variant only (AEC-Q100 Grade 0, automotive grade flow).
