LTC2392ILX-16 - 16-Bit 500ksps SAR ADC, 94dB SNR | Analog Devices
Артикул: LTC2392ILX-16 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.2 | $162,00 |
| 100 | $14.05 | $1.405,00 |
| 500 | $12.4 | $6.200,00 |
| 1.000 | $11.1 | $11.100,00 |
LTC2392ILX-16 Обзор
A SAR (Successive Approximation Register) ADC converts a single analog sample to a digital code using a binary-search algorithm against an internal DAC, trading flash speed for high resolution with low power and zero pipeline latency. The LTC2392-16 sits in the precision data-acquisition tier of Analog Devices' ADC portfolio — between general-purpose successive-approximation parts and the higher-speed pipelined converters — and is widely deployed where accurate capture of slowly changing or wide-bandwidth signals is required without sacrificing throughput.
Key feature highlights include simultaneous SPI-compatible serial and parallel data interfaces with no cycle latency, hardware-selectable nap and sleep power-down modes that reduce quiescent current to nanoampere levels between conversions, and fast full-scale settling that allows the device to react promptly to large input steps after power-down. The combination of ±4.096V true-differential inputs, internal reference, and 110 mW typical dissipation at 500ksps makes the part well suited to industrial process-control and instrumentation front-ends. The 48-pin LQFP-48 (7x7 mm) footprint is compatible with the LTC2392 family, and a commercial-grade variant (LTC2392CLX-16) covers the 0 °C to +70 °C window for cost-sensitive applications.
Typical applications include high-speed industrial process monitoring, precision weigh scales, instrumentation and data acquisition boards, and motor control feedback loops. The wide bipolar input range and fast settling also suit the part for use in multiplexed channel scanning and medical instrumentation front-ends. When designing in the LTC2392ILX-16, pay attention to input common-mode and reference-decoupling layout; place 10 µF bypass capacitors as close as possible to the REFP, REFN, and VDD pins to realize the rated 94 dB SNR.
Аналоги без доработки для LTC2392ILX-16 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LTC2392ILX-16 (тот же форм-фактор и посадочное место) — отличается по Number of Input Channels, Operating Temperature Range, RoHS Status, Digital Interface, Sampling Rate.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LTC2392CLX-16
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2392ILX-16#PBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2392ILX-16/UE
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC2389ILX-16
✅ Прямая замена✓ В наличии
$35.21 / шт.
Открыть даташит →LTC2391IUK-16
✅ Прямая замена✓ В наличии
$17.4 / шт.
Открыть даташит →LTC2335HLX-16
✅ Прямая замена✓ В наличии
$15.4 / шт.
Открыть даташит →LTC2392ILX-16 Максимальные параметры и электрические характеристики
| Number of Bits | 16 |
| Частота дискретизации | 500 ksps |
| Architecture | SAR (Successive Approximation Register) |
| Number of Input Channels | 1 |
| Input Range | ±4.096 V fully differential |
| SNR | 94 dB |
| Напряжение питания | 5 V (single) |
| Reference | Internal, 0.5% initial accuracy, ±20 ppm/°C max TC |
| Data Interface | Serial (SPI-compatible) and Parallel |
| Корпус | 48-LQFP (7x7 mm) |
| Рабочая температура | -40 °C to +85 °C |
| Power Dissipation | 110 mW at 500 ksps |
| Power-Down Modes | Nap and Sleep (nA quiescent) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant (PBF suffix) |
Конфигурация выводов LTC2392ILX-16
| Контакт 1 | AIN+ — Positive analog input |
| Контакт 2 | AIN- — Negative analog input |
| Контакт 3 | GND — Analog ground |
| Контакт 4 | REF — Reference input/output |
| Контакт 5 | REFP — Reference buffer positive |
| Контакт 6 | REFN — Reference buffer negative |
| Контакт 7 | VDD — 5V analog supply |
| Контакт 8 | OVDD — Digital I/O supply |
| Контакт 9 | GND — Digital ground |
| Контакт 10 | CLK — Conversion clock / serial clock |
| Контакт 11 | CS — Chip select (active low) |
| Контакт 12 | RD — Read strobe (parallel) |
| Контакт 13 | CONVST — Conversion start |
| Контакт 14 | BUSY — Conversion in progress (active high) |
| Контакт 15 | SDOUT — Serial data output (SPI) |
| Контакт 16 | D0/D15 — Parallel data bit 0 / serial bit 15 |
| Контакт 17 | D1/D14 — Parallel data bit 1 / serial bit 14 |
| Контакт 18 | D2/D13 — Parallel data bit 2 / serial bit 13 |
| Контакт 19 | D3/D12 — Parallel data bit 3 / serial bit 12 |
| Контакт 20 | D4/D11 — Parallel data bit 4 / serial bit 11 |
| Контакт 21 | D5/D10 — Parallel data bit 5 / serial bit 10 |
| Контакт 22 | D6/D9 — Parallel data bit 6 / serial bit 9 |
| Контакт 23 | D7/D8 — Parallel data bit 7 / serial bit 8 |
| Контакт 24 | GND — Digital ground |
| Контакт 25 | D8 — Parallel data bit 8 |
| Контакт 26 | D9 — Parallel data bit 9 |
| Контакт 27 | D10 — Parallel data bit 10 |
| Контакт 28 | D11 — Parallel data bit 11 |
| Контакт 29 | D12 — Parallel data bit 12 |
| Контакт 30 | D13 — Parallel data bit 13 |
| Контакт 31 | D14 — Parallel data bit 14 |
| Контакт 32 | D15 — Parallel data bit 15 (MSB) |
| Контакт 33 | GND — Digital ground |
| Контакт 34 | NAP — Nap power-down mode (active low) |
| Контакт 35 | SLEEP — Sleep power-down mode (active low) |
| Контакт 36 | RDL/SDI — Read latch / serial data input |
| Контакт 37 | RESET — Reset (active low) |
| Контакт 38 | OGND — Output driver ground |
| Контакт 39 | OVDD — Output driver supply |
| Контакт 40 | VDD — Analog supply |
| Контакт 41 | GND — Analog ground |
| Контакт 42 | REFGND — Reference ground |
| Контакт 43 | VREF — External reference input (optional) |
| Контакт 44 | REFOUT — Internal reference output |
| Контакт 45 | COM — Common-mode voltage output |
| Контакт 46 | IN+ — Positive input buffer |
| Контакт 47 | IN- — Negative input buffer |
| Контакт 48 | GND — Analog ground |
Типичное применение
LTC2392ILX-16 подходит для 6 применениеs: High-Speed Industrial Process Control, Precision Weigh Scale Front-End, Automated Test Equipment Data Acquisition, Motor Control Current Sensing, Medical Instrumentation Signal Chain, Multiplexed Sensor Scanning Systems.
High-Speed Industrial Process Control
The LTC2392ILX-16 is well matched to industrial process-control front-ends because of its 500 ksps throughput combined with 16-bit resolution and ±4.096 V true differential input range. At 500 ksps it can capture 4-20 mA-derived signals from multiple multiplexed sensor channels while preserving 94 dB SNR per channel, so loop controllers see precise feedback. Placed at the analog back-end of a sigma-delta or multi-channel scanning topology, it provides no-latency SAR conversion that complements the slower but higher-resolution signal-chain stages without introducing pipeline delay.
Рекомендуется
Precision Weigh Scale Front-End
In precision weigh-scale designs the LTC2392ILX-16's 94 dB SNR and ±4.096 V differential input let the load-cell output be digitized directly without an instrumentation amplifier front-end. The internal precision reference with ±20 ppm/°C maximum TC keeps scale calibration stable across ambient shifts, while 16-bit resolution delivers more than 19 effective bits at 500 ksps for accurate force measurement. Nap and sleep power-down modes extend battery run time in portable scales by gating the ADC between active conversion cycles, with no warm-up penalty on reactivation.
Рекомендуется
Automated Test Equipment Data Acquisition
ATE racks benefit from the LTC2392ILX-16's 500 ksps throughput and simultaneous SPI/parallel digital interface, which permits a single ADC to feed both an MCU and an FPGA capture buffer. The 94 dB SNR enables sub-millivolt measurement resolution on test waveforms, while the ±4.096 V differential input accepts raw DUT outputs from instrumentation without scaling. Hardware-selectable nap and sleep modes let the ATE controller shut the ADC between pin-list transitions, reducing thermal drift in long production-test cycles.
Рекомендуется
Motor Control Current Sensing
Three-phase motor-control boards use the LTC2392ILX-16 to digitize phase-current shunts and DC-bus currents at 500 ksps — fast enough for FOC feedback loops where conversion latency is critical. SAR architecture's zero pipeline delay translates directly into shorter loop dead-time, which improves torque-ripple performance at high PWM rates. The ±4.096 V differential range captures full shunt excursions during transient events such as motor starts or direction reversals, and the internal reference keeps calibration stable across controller temperature rises.
Рекомендуется
Medical Instrumentation Signal Chain
Patient-monitoring instruments and diagnostic analyzers benefit from the LTC2392ILX-16's 94 dB SNR and ±4.096 V bipolar input, which permit direct digitization of front-end amplifier outputs without a second gain stage. At 500 ksps the part captures ECG, EEG, or pulse-oximetry waveforms with more than 16 bits of usable resolution, supporting accurate medical-grade analysis. The internal precision reference removes a temperature-sensitive external component, helping the channel meet long-term stability requirements for clinical instruments.
Рекомендуется
Multiplexed Sensor Scanning Systems
Multi-channel sensor-data-acquisition boards put the LTC2392ILX-16 after an analog multiplexer to scan 8, 16, or more input channels at high rates while keeping per-channel SNR above 94 dB. Nap and sleep modes enable duty-cycling the ADC only for the active channel, eliminating the need for channel-specific analog front-end stages. The simultaneous SPI/parallel output lets a single ADC feed both a slow MCU housekeeping channel and a fast FPGA sample capture, reducing board complexity.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LTC2392ILX-16 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LTC2392CLX-16 | LTC2389ILX-16 | LTC2391IUK-16 | LTC2335HLX-16 |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) | 36-QFN (referenced but surveyed for compatibility) | 48-LQFP (7x7) |
| Resolution | 16-bit | 16-bit | 18-bit | 16-bit | 16-bit |
| Temperature Grade | -40°C to +85°C (Industrial) | 0°C to +70°C (Commercial) | -40°C to +85°C (Industrial) | -40°C to +85°C (Industrial) | -40°C to +85°C (Industrial) |
Ключевые отличия
- Zero pipeline latency at full 500 ksps throughput with ±4.096 V true bipolar differential input (против LTC2389ILX-16)
- Higher throughput than the sister LTC2391IUK-16 family member at the same 16-bit resolution (против LTC2391IUK-16)
- Integrated internal precision reference with ±20 ppm/°C maximum TC removes an external IC (против LTC2335HLX-16)
Заметки по проектированию
Place 10 µF X7R ceramic decoupling capacitors as close as possible to the REFP, REFN, and VDD pins of the LTC2392ILX-16. A separate 0.1 µF bypass capacitor should be placed in parallel with each 10 µF for high-frequency noise suppression. Keep analog and digital ground returns separated on a split PCB plane and tie them together under the GND pins of the ADC. Long trace inductance between the bypass capacitors and the ADC pins is the single most common cause of degraded 94 dB SNR performance.
When operating the LTC2392ILX-16 at -40 °C to +85 °C industrial grade, do not enter the nap or sleep power-down modes without allowing the internal reference to settle for the time specified in the datasheet after exit. Premature conversion-start pulses during reference wake-up will produce erroneous codes. Also ensure that the SPI/parallel mode pins are not left floating at power-up; tie them to OVDD or OGND through 100 kΩ resistors, or the host MCU must drive them deterministically before the first CONVST strobe.
Estimated: at the maximum 500 ksps throughput, the LTC2392ILX-16 dissipates approximately 110 mW on a 5 V supply, which through the 48-LQFP package's typical θJA of ~45 °C/W yields a junction-to-ambient rise of roughly 5 °C above ambient at room temperature. Inside a sealed enclosure with 50 °C ambient, the junction would still stay below +95 °C, well inside the 125 °C maximum rating. For higher ambient enclosures consider airflow over the part or a copper pour under the thermal pad to keep junction rise modest.
Use symmetric PCB trace routing for the AIN+ and AIN- differential pair from the input driver to the LTC2392ILX-16 inputs, and match the trace lengths within 50 mils to keep differential mode rejection balanced. Route the analog input traces on a separate layer from the digital SPI/parallel data lines, ideally with a continuous ground plane in between, to avoid digital switching noise coupling into the analog front-end. Place the 10 µF input common-mode filter capacitor near pin 45 (COM) and the differential input RC network directly at the AIN+/AIN- pins.
Информация о соответствии
RoHS compliance indicated by the #PBF suffix on all official distributor listings. This part is not AEC-Q100 qualified and is not intended for automotive powertrain applications; it is industrial- and instrumentation-grade only. Halogen-free status was not confirmed in the verified web data and is reported as 'unknown'.
