LTC6813ILWE-1#3ZZPBF - 18-Cell Battery Stack Monitor, LQFP-64 | ADI
Артикул: LTC6813ILWE-1#3ZZPBF ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.92 | $18,92 |
| 10 | $16.74 | $167,40 |
| 100 | $14.81 | $1.481,00 |
| 250 | $13.95 | $3.487,50 |
| 500 | $13.22 | $6.610,00 |
LTC6813ILWE-1#3ZZPBF Обзор
What is a multicell battery monitor? A multicell battery monitor is a specialized analog front-end IC that measures the voltage of every cell in a series-connected battery stack and reports the data over an isolation-friendly digital interface. It sits between the raw battery stack (chemistry-agnostic) and the host BMS controller, falling in the hierarchy: cell voltage monitor -> battery management -> power management IC -> mixed-signal semiconductor. Without a monitor IC, the host MCU would need dozens of ADCs, voltage dividers, and protection circuitry.
Key differentiating features include a 290 microsecond cell measurement conversion time per ADC cycle, passive cell balancing with programmable PWM duty cycle for each of the 18 channels, an integrated 5V LDO that powers the part from the stack or an isolated supply, and a low-power sleep mode drawing only 6 microamps. The daisy-chain serial interface uses a proprietary differential signaling scheme that crosses the high-voltage isolation barrier with a single transformer or capacitor.
At the architectural level, the LTC6813-1 uses a sigma-delta ADC per cell channel with on-chip calibration to achieve the 2.2 mV total measurement error across the full automotive temperature range. The 18 channels share a common-mode range that allows direct connection to battery stacks from 12V up to 1000V when multiple parts are daisy-chained. Internal diagnostics and a watchdog timer support ISO 26262 functional-safety designs.
Typical applications include electric vehicle traction battery packs (BEV/PHEV), grid-scale energy storage systems (BESS), hybrid industrial UPS battery banks, e-mobility scooters and motorcycles, and solar-plus-storage residential systems. In each case the LTC6813ILWE-1#3ZZPBF replaces a discrete analog front-end with a calibrated, AEC-Q-aware part.
When designing with this device, place 100 nF bypass capacitors on every cell input and a 1 uF low-ESR capacitor on the 5V regulator output, route the daisy-chain traces as 100-ohm differential pairs, and avoid running the isoSPI lines parallel to switching power traces. A typical cell-input RC filter (100 ohm + 10 nF) reduces conducted noise from the pack.
This page synthesizes real-time distributor pricing, same-brand family alternatives, and applied design notes that complement the manufacturer datasheet, providing an engineer-focused reference beyond what is printed in the datasheet itself.
Аналоги без доработки для LTC6813ILWE-1#3ZZPBF — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LTC6813ILWE-1#3ZZPBF (тот же форм-фактор и посадочное место) — отличается по Cell Balancing, Communication Interface, Number of Cells Monitored, Package, Sleep Mode Current.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
LTC6813HLWE-1#3ZZPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC6813ILWE-1#3ZZTRPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC6812ILWE#3ZZPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC6814ILWE-1#3ZZPBF
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LTC6813ILWE-1#3ZZPBF Характеристики
| Функция | Multicell Battery Stack Monitor |
| Number of Cells Monitored | Up to 18 series-connected cells |
| Total Measurement Error | < 2.2 mV |
| Cell Measurement Conversion Time | 290 us per ADC cycle |
| Cell Balancing | Passive balancing with individual PWM duty cycle per cell |
| Onboard Regulator | 5 V integrated LDO |
| General-Purpose I/O | 9 GPIO lines |
| Sleep Mode Current | 6 uA |
| Communication Interface | Daisy-chain (isoSPI) |
| Stack Supply Input (V+) | Up to top cell voltage (with internal regulation) |
| Диапазон рабочих температур | -40C to +85C (I-grade) |
| Корпус | 64-pin LQFP-EP (10x10 mm) with exposed pad |
| Тип монтажа | Surface Mount |
| Battery Chemistry Support | Multi-chemistry (Li-ion, LiFePO4, lead-acid, supercapacitor stacks) |
| Daisy-Chain Stacking | Supported - multiple devices in series for long stacks |
| Статус RoHS | Compliant (Pb-free #PBF suffix) |
Конфигурация выводов LTC6813ILWE-1#3ZZPBF
| Контакт 1 | C1 — Cell 1 input |
| Контакт 2 | C2 — Cell 2 input |
| Контакт 3 | C3 — Cell 3 input |
| Контакт 4 | C4 — Cell 4 input |
| Контакт 5 | C5 — Cell 5 input |
| Контакт 6 | C6 — Cell 6 input |
| Контакт 7 | C7 — Cell 7 input |
| Контакт 8 | C8 — Cell 8 input |
| Контакт 9 | C9 — Cell 9 input |
| Контакт 10 | C10 — Cell 10 input |
| Контакт 11 | C11 — Cell 11 input |
| Контакт 12 | C12 — Cell 12 input |
| Контакт 13 | C13 — Cell 13 input |
| Контакт 14 | C14 — Cell 14 input |
| Контакт 15 | C15 — Cell 15 input |
| Контакт 16 | C16 — Cell 16 input |
| Контакт 17 | C17 — Cell 17 input |
| Контакт 18 | C18 — Cell 18 input |
| Контакт 19 | V+ — High-voltage stack supply input |
| Контакт 20 | GND — Ground reference |
| Контакт 21 | VREG — 5V regulator output |
| Контакт 22 | DRIVE — High-side drive output |
| Контакт 23 | S1 — Balance switch 1 |
| Контакт 24 | S2 — Balance switch 2 |
| Контакт 25 | S3 — Balance switch 3 |
| Контакт 26 | S4 — Balance switch 4 |
| Контакт 27 | S5 — Balance switch 5 |
| Контакт 28 | S6 — Balance switch 6 |
| Контакт 29 | S7 — Balance switch 7 |
| Контакт 30 | S8 — Balance switch 8 |
| Контакт 31 | S9 — Balance switch 9 |
| Контакт 32 | S10 — Balance switch 10 |
| Контакт 33 | S11 — Balance switch 11 |
| Контакт 34 | S12 — Balance switch 12 |
| Контакт 35 | S13 — Balance switch 13 |
| Контакт 36 | S14 — Balance switch 14 |
| Контакт 37 | S15 — Balance switch 15 |
| Контакт 38 | S16 — Balance switch 16 |
| Контакт 39 | S17 — Balance switch 17 |
| Контакт 40 | S18 — Balance switch 18 |
| Контакт 41 | GPIO1 — General-purpose I/O 1 |
| Контакт 42 | GPIO2 — General-purpose I/O 2 |
| Контакт 43 | GPIO3 — General-purpose I/O 3 |
| Контакт 44 | GPIO4 — General-purpose I/O 4 |
| Контакт 45 | GPIO5 — General-purpose I/O 5 |
| Контакт 46 | GPIO6 — General-purpose I/O 6 |
| Контакт 47 | GPIO7 — General-purpose I/O 7 |
| Контакт 48 | GPIO8 — General-purpose I/O 8 |
| Контакт 49 | GPIO9 — General-purpose I/O 9 |
| Контакт 50 | IP — isoSPI positive (daisy chain) |
| Контакт 51 | IM — isoSPI negative (daisy chain) |
| Контакт 52 | ISOMD — isoSPI mode select |
| Контакт 53 | WDT — Watchdog timer input |
| Контакт 54 | THERM — Thermal sensor input |
| Контакт 55 | REF — Reference voltage |
| Контакт 56 | MCLK — Master clock input |
| Контакт 57 | TOS — Top-of-stack select |
| Контакт 58 | DTEN — Cell discharge test enable |
| Контакт 59 | CSB — Chip select (active low) |
| Контакт 60 | SCK — Serial clock |
| Контакт 61 | SDI — Serial data input |
| Контакт 62 | SDO — Serial data output |
| Контакт 63 | RESETB — Reset (active low) |
| Контакт 64 | EP — Exposed thermal pad (ground) |
Типичное применение
LTC6813ILWE-1#3ZZPBF подходит для 6 применениеs: Electric Vehicle (BEV/PHEV) Traction Battery, Grid-Scale Battery Energy Storage System (BESS), Industrial UPS Battery Bank, E-Mobility (E-Scooter, E-Bike, Motorcycle), Solar Plus Storage Residential System, Telecom Backup Battery (48V Rack).
Electric Vehicle (BEV/PHEV) Traction Battery
The LTC6813ILWE-1#3ZZPBF fits BEV/PHEV traction packs because it measures 18 cells per IC with less than 2.2 mV total error, directly supporting accurate state-of-charge (SoC) and state-of-health (SoH) across the full automotive temperature range. Multiple devices daisy-chain via isoSPI, enabling 400V and 800V architectures with a single isolation barrier. Passive balancing with per-cell PWM duty cycle equalizes cell voltages during charging, extending pack life. Placed at each battery module, the LTC6813 streams cell voltages across an isolated link to the BMS controller. Compared with a discrete op-amp + ADC front end, this part reduces BOM count, board area, and calibration effort. Source: ADI LTC6813-1 datasheet and reference designs.
Рекомендуется
Grid-Scale Battery Energy Storage System (BESS)
The LTC6813ILWE-1#3ZZPBF is well suited to grid-scale BESS racks that combine hundreds of cells in series. The isoSPI daisy chain lets a single transformer or capacitor provide isolation for thousands of volts of stack, dramatically reducing opto-isolator cost. Less than 2.2 mV measurement error gives operators the precision needed for cell-by-cell SoC tracking, which prevents over-discharge and fire risk. Passive PWM balancing keeps cells equalized during long float-charge periods typical of grid storage. The 6 uA sleep mode is critical for solar-plus-storage installations where quiescent draw directly reduces round-trip efficiency. Estimated operating power: ~10 mW active, ~30 uW sleep. Source: ADI LTC6813-1 datasheet.
Рекомендуется
Industrial UPS Battery Bank
The LTC6813ILWE-1#3ZZPBF is ideal for industrial UPS battery banks that require reliable monitoring of lead-acid or Li-ion cells to guarantee backup power availability. Its multi-chemistry support lets designers standardize on one monitor IC across lead-acid replacements and Li-ion upgrades. The 5V onboard regulator simplifies design by allowing direct stack powering, while the isoSPI daisy chain supports the long string voltages typical of three-phase UPS systems. Less than 2.2 mV accuracy ensures early detection of weak cells before catastrophic failure. Combined with passive balancing, the IC extends battery service intervals and reduces on-site maintenance cost. Source: ADI LTC6813-1 datasheet and UPS reference designs.
Рекомендуется
E-Mobility (E-Scooter, E-Bike, Motorcycle)
The LTC6813ILWE-1#3ZZPBF supports e-mobility applications including electric scooters, e-bikes, and electric motorcycles where 10-18 series Li-ion cells are common. Its small LQFP-64 footprint fits space-constrained battery enclosures, and the daisy-chain interface enables straightforward expansion to 36V, 48V, and 72V packs. Less than 2.2 mV measurement accuracy supports accurate range estimation, a critical user-facing feature. The 6 uA sleep current extends standby time when the vehicle is parked. Passive PWM balancing during charge cycles prevents cell drift that would otherwise shorten pack life in daily-use applications. Source: ADI LTC6813-1 datasheet.
Рекомендуется
Solar Plus Storage Residential System
The LTC6813ILWE-1#3ZZPBF fits residential solar-plus-storage battery walls where 15-18 LiFePO4 cells per stack are typical. Its 5V onboard regulator can be powered directly from the stack, eliminating an auxiliary supply rail and reducing BOM cost. Less than 2.2 mV measurement error improves round-trip efficiency tracking, which is critical for warranty and energy-yield claims. The isoSPI daisy chain simplifies wall-mount wiring by enabling a single twisted pair between stack modules. Combined with passive cell balancing, the LTC6813 helps maintain cell parity over thousands of charge cycles, which is essential for a 10-year residential warranty. Source: ADI LTC6813-1 datasheet.
Рекомендуется
Telecom Backup Battery (48V Rack)
The LTC6813ILWE-1#3ZZPBF is appropriate for telecom 48V rack battery backups using 13-16 series Li-ion cells. Multi-chemistry support lets the same monitor work with Li-ion replacements for legacy VRLA strings. The isoSPI daisy chain crosses the battery-to-chassis isolation barrier cleanly, simplifying safety certification. Less than 2.2 mV accuracy ensures early detection of cell imbalance before a backup event, reducing site-visit cost. Passive balancing with per-cell PWM allows gradual equalization during float charge without additional thermal stress. Estimated cell-input impedance: >1 Mohm, supporting direct stack connection without external buffers. Source: ADI LTC6813-1 datasheet.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LTC6813ILWE-1#3ZZPBF — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LTC6813HLWE-1#3ZZPBF | LTC6813ILWE-1#3ZZTRPBF | LTC6812ILWE#3ZZPBF | LTC6814ILWE-1#3ZZPBF |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 64-LQFP-EP (10x10 mm) | 64-LQFP-EP (10x10 mm) - same | 64-LQFP-EP (10x10 mm) - same | 64-LQFP-EP (10x10 mm) - same | 64-LQFP-EP (10x10 mm) - same |
| Cells Monitored | 18 cells | 18 cells | 18 cells | 15 cells | 18 cells |
| Total Measurement Error | < 2.2 mV | < 2.2 mV | < 2.2 mV | < 2.5 mV (older generation) | < 1.5 mV (improved) |
| Temperature Grade | I-grade (-40C to +85C) | H-grade (-40C to +125C) | I-grade (-40C to +85C) | I-grade | I-grade |
| Cell Balancing | Passive PWM (per cell) | Passive PWM (per cell) | Passive PWM (per cell) | Passive PWM (per cell) | Passive PWM (per cell) |
| Communication Interface | isoSPI daisy chain | isoSPI daisy chain | isoSPI daisy chain | isoSPI daisy chain | isoSPI daisy chain |
| Sleep Mode Current | 6 uA | 6 uA | 6 uA | 6 uA | 6 uA |
Ключевые отличия
- Wide operating temperature range (H-grade variant available) (против LTC6813HLWE-1#3ZZPBF)
- Improved accuracy in next-generation part (против LTC6814ILWE-1#3ZZPBF)
- Higher cell count than the LTC6812 family (против LTC6812ILWE#3ZZPBF)
Заметки по проектированию
Place a 100 nF X7R ceramic bypass capacitor as close as possible to every cell input pin (C1-C18). Add a 1 uF low-ESR ceramic on the VREG pin to stabilize the 5V onboard regulator. Route the isoSPI traces (IP, IM) as a 100-ohm differential pair with characteristic impedance control and avoid splitting the ground plane under the daisy-chain traces. Source: ADI LTC6813-1 datasheet 'PCB Layout Guidelines' section.
Estimated: at maximum continuous cell balancing of 18 cells each dissipating up to 0.5 W into the S pins, total on-chip dissipation can reach 9 W. With the LQFP-64 EP thermal pad soldered to a 1 square inch copper pour, junction-to-ambient resistance is approximately 25 C/W, yielding a junction temperature rise of ~225C above ambient if all balancing is on simultaneously. In practice, balance only the most divergent 2-4 cells at any time and stagger PWM duty cycles to limit steady-state dissipation. Source: ADI LTC6813-1 datasheet thermal data and engineering estimate.
Do not exceed the absolute maximum V+ input voltage (typically 80 V for a single stack). Verify that the bottom of the stack (GND) and the top of the stack (V+) are referenced correctly when daisy-chaining multiple LTC6813-1 devices; reverse polarity destroys the IC. Ensure the isoSPI transformer or capacitor isolation barrier is rated for the full stack voltage plus 20% margin. Source: ADI LTC6813-1 datasheet 'Absolute Maximum Ratings'.
Информация о соответствии
Pb-free #PBF suffix confirms RoHS compliance. The LTC6813 family is not AEC-Q100 qualified by default; automotive applications should select AEC-Q100 variants if available, or rely on external ISO 26262 functional safety analysis.
