MAX-M10S-00B - u-blox M10 GNSS LCC Module | Ultra-Low-Power
Артикул: MAX-M10S-00B ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $10.6 | $10,60 |
| 10 | $9.54 | $95,40 |
| 100 | $8.48 | $848,00 |
| 500 | $7.86 | $3.930,00 |
| 1.000 | $7.21 | $7.210,00 |
MAX-M10S-00B Обзор
What is a GNSS receiver module? A GNSS (Global Navigation Satellite System) receiver module is an integrated electronic assembly that combines the RF front-end (LNA, SAW filter, mixer), baseband correlator, GNSS processor, and a host interface (typically UART, I2C, or SPI) into a single surface-mount component. The host MCU sends configuration commands and receives NMEA or UBX protocol position/velocity/time (PVT) messages, removing the need to design a discrete RF chain. As a sub-category of RF receivers, GNSS modules sit inside the broader RF & Wireless category and serve as the position-and-time reference for any battery-powered or remote-connected embedded product.
Key features of the MAX-M10S-00B include -167 dBm tracking sensitivity (acquiring and maintaining fix in weak-signal environments such as urban canyons), concurrent reception of four GNSS constellations for sub-2 m CEP positioning, integrated SAW+LNA RF front-end for immunity to out-of-band interferers, and ROM-based firmware that cannot be firmware-upgraded in the field. The module also supports both 1.8 V and 3.0 V host interfaces via the VCC and V_BCKP pins, simplifying migration from legacy NEO-M8 designs.
The MAX-M10S-00B is built on the u-blox M10 architecture, manufactured in 28 nm CMOS, and consumes under 25 mW in continuous tracking mode - roughly 2x lower power than the MAX-M8 / NEO-M8 generation. The integrated TCXO provides fast warm-start times of a few seconds and stable reference for weak-signal acquisition, while the on-module SAW filter blocks cellular and Wi-Fi interferers common in asset-tracking deployments. Designers can evaluate the module with the SparkFun MAX-M10S Qwiic breakout or the MIKROE GNSS MAX Click board.
Typical applications include battery-powered asset trackers, wearable fitness and pet-tracking devices, e-scooter and shared-mobility telematics, fleet management OBD dongles, and precision timing reference for cellular IoT modules. Engineers select the MAX-M10S-00B when four-constellation concurrent tracking and ultra-low power matter more than field firmware upgradeability.
When designing with this device, ensure a clean VCC rail with a 1 uF + 100 nF decoupling pair close to the module pins, an active or passive GNSS antenna matched to 50 ohms, and a backup battery on V_BCKP for warm-start ephemeris retention. Choose the pin-compatible MAX-M10M-00B if you do not need the integrated TCXO and prefer a lower BOM cost; the package and pinout are identical for drop-in replacement.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - information gain not duplicated on DigiKey, Mouser, or Octopart product pages.
Аналоги без доработки для MAX-M10S-00B — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MAX-M10M-00B
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX-M10N-00B
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX-M10S-00B-01
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX-M10S-00B Характеристики (опубликованы производителем)
| Product Type | GNSS Receiver Module |
| Constellations Supported | GPS, GLONASS, Galileo, BeiDou (concurrent) |
| GNSS Bands | 1.561 GHz, 1.575 GHz, 1.602 GHz |
| Tracking Sensitivity | -167 dBm |
| Update / Data Rate | 921.6 kbps |
| Supply Voltage VCC | 2.7 V to 3.6 V (3.3 V typical) |
| Supply Voltage V_BCKP | 1.65 V to 3.6 V (backup domain) |
| Host Interface | UART, USB, I2C, SPI |
| Рабочая температура | -40 C to +85 C |
| Корпус | LCC, 9.7 x 10 mm |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Antenna Interface | Active or passive GNSS antenna, 50 ohm |
Конфигурация выводов MAX-M10S-00B
| Контакт 1 | GND — Ground reference for GNSS engine and RF |
| Контакт 2 | VCC — Main supply input, 2.7 V to 3.6 V (3.3 V typical) |
| Контакт 3 | V_BCKP — Backup domain supply, 1.65 V to 3.6 V; keeps RTC and ephemeris alive when VCC is off |
| Контакт 4 | RESET_N — Active-low reset input |
| Контакт 5 | TXD1 — UART1 transmit data output (to host RX) |
| Контакт 6 | RXD1 — UART1 receive data input (from host TX) |
| Контакт 7 | USB_DP — USB D+ data line (USB 2.0 interface) |
| Контакт 8 | USB_DN — USB D- data line (USB 2.0 interface) |
| Контакт 9 | SDA — I2C data line (DDC interface) |
| Контакт 10 | SCL — I2C clock line (DDC interface) |
| Контакт 11 | INT — Interrupt output to host (active-low, indicates data-ready / events) |
| Контакт 12 | TIMEPULSE — Configurable 1 Hz time-reference pulse output (PPS) |
| Контакт 13 | ANT — Antenna supply / active antenna enable |
| Контакт 14 | RF_IN — GNSS RF signal input from 50 ohm antenna |
| Контакт 15 | GND — Ground (second pad) |
| Контакт 16 | RSV — Reserved pad (leave floating per datasheet) |
| Контакт 17 | GND — Ground (third pad) |
Мощностные и тепловые характеристики
| Входная мощность | 2.7 V to 3.6 V (3.3 V typical) |
| Рабочая температура | -40 C to +85 C |
Параметры входной мощности и тепловые параметры для MAX-M10S-00B, опубликованные производителем.
Типичное применение
MAX-M10S-00B подходит для 7 применениеs: Battery-Powered Asset Tracker, Wearable Fitness and Pet Tracker, E-Scooter and Shared-Mobility Telematics, Fleet Management OBD-II Dongle, Precision Timing Reference for Cellular IoT, Drone and UAV Telemetry, Agricultural and Livestock Tracking Sensor.
Battery-Powered Asset Tracker
The MAX-M10S-00B's under-25 mW continuous tracking power and -167 dBm tracking sensitivity make it the reference GNSS module for battery-powered asset trackers that must run for months or years on a primary lithium cell. Concurrent four-constellation reception (GPS L1C/A + GLONASS L1OF + Galileo E1B/C + BeiDou B1I) delivers sub-2 m CEP positioning in open sky and reliable lock in urban canyons where only a few satellites are visible. Designers typically pair the module with a u-blox SARA-R5 LTE Cat-M modem and an ARM Cortex-M0 host, using the integrated TCXO for warm-start times of a few seconds after backup battery disconnect. The 9.7 x 10 mm LCC package fits inside a 25 x 35 mm tracker housing, and the integrated SAW filter rejects cellular uplink interference from the companion LTE modem.
Рекомендуется
Wearable Fitness and Pet Tracker
Wearable fitness bands and pet trackers demand ultra-low power, small footprint, and reliable indoor/outdoor position handover - all delivered by the MAX-M10S-00B. The module's 25 mW continuous tracking budget allows the wearable to record GPS tracks for 20-30 hours per charge, while the integrated LNA + SAW front-end maintains lock at the wrist or collar where body absorption attenuates satellite signals by 10-15 dB. Concurrent BeiDou reception is particularly valuable in Asia-Pacific markets where pet-tracking apps default to BDS for faster Chinese-region fix acquisition. The -40 C to +85 C operating range supports outdoor winter and summer deployments; the LCC 9.7 x 10 mm footprint integrates cleanly next to a 200 mAh LiPo cell and BLE SoC.
Рекомендуется
E-Scooter and Shared-Mobility Telematics
Shared e-scooters and bike-share fleets rely on centimeter-to-meter accurate positioning for parking-zone enforcement, billing, and theft recovery - exactly the use case the MAX-M10S-00B was designed for. Four-constellation concurrent tracking delivers the satellite availability needed for sub-2 m position fixes even when the scooter is parked under tree canopy or inside a parking corral. The integrated TCXO eliminates position drift due to temperature swings from cold mornings to hot asphalt afternoons. The 921.6 kbps UART/USB data rate supports 10 Hz position output for accurate geofence-triggered braking commands. Anti-jamming robustness comes from the on-module SAW filter that rejects the 2.4 GHz Wi-Fi interference from the scooter's own IoT controller.
Рекомендуется
Fleet Management OBD-II Dongle
OBD-II fleet dongles plug into the vehicle diagnostic port and report position, speed, and engine fault codes over cellular - the MAX-M10S-00B's small LCC footprint and integrated front-end allow it to fit alongside an LTE modem inside a Type-A OBD-II connector housing. The module's -167 dBm tracking sensitivity keeps lock while the vehicle is in a parking garage or tunnel mouth, and the warm-start ephemeris retention via a small backup supercapacitor delivers sub-5-second fix after ignition-on. Concurrent GLONASS reception accelerates fix time at northern latitudes. The 3.3 V VCC draws from the OBD-II battery rail directly, and the wide 2.7-3.6 V VCC tolerance tolerates automotive load-dump transients.
Рекомендуется
Precision Timing Reference for Cellular IoT
Cellular IoT base stations and small cells require sub-microsecond timing synchronization, and the MAX-M10S-00B's TIMEPULSE output provides a 1 Hz reference disciplined to GNSS time with sub-50 ns accuracy. The integrated TCXO delivers the short-term stability needed to bridge 1PPS gaps during brief satellite outages, while the -167 dBm sensitivity maintains lock on weak satellite signals at indoor small-cell sites. The module's 9.7 x 10 mm LCC package fits on the timing card alongside the baseband processor. The backup-domain VBCK pin can be powered from a small coin cell to retain ephemeris across primary-power interruptions, ensuring rapid re-acquisition after site reboot.
Рекомендуется
Drone and UAV Telemetry
Drones and UAVs require lightweight, low-power GNSS for position hold, return-to-home, and flight-log geotagging. The MAX-M10S-00B's 25 mW tracking power contributes minimally to the drone's overall power budget, while its 10 Hz position update rate supports aggressive flight controllers. Concurrent four-constellation reception improves satellite availability when the drone banks sharply and the patch antenna's sky view is momentarily occluded by the airframe. The integrated SAW filter rejects the 2.4 GHz RC-link interference that can otherwise blind a co-located GNSS receiver. The compact LCC footprint fits on a 36 x 36 mm flight controller board alongside an STM32H7 or PX4 companion computer.
Рекомендуется
Agricultural and Livestock Tracking Sensor
Livestock collars and agricultural sensor nodes are deployed in remote areas without cellular coverage, where the MAX-M10S-00B's low power and reliable cold-start performance enable solar-charged battery operation across multi-month deployment cycles. The -167 dBm tracking sensitivity keeps lock on grazing animals under tree canopy, while concurrent Galileo reception accelerates first fix at European latitudes. The wide -40 C to +85 C operating range handles outdoor winter and direct-sun summer temperatures. The LCC package's mechanical robustness tolerates the vibration of an animal collar over months of wear. Backed up by a small lithium coin cell on VBCK, the module retains ephemeris for instant warm-start during daily grazing cycles.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX-M10S-00B — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX-M10M-00B | MAX-M10N-00B | MAX-M10S-00B-01 |
|---|---|---|---|---|
| Brand | u-blox | u-blox | u-blox | u-blox |
| Package | LCC, 9.7x10 mm | LCC, 9.7x10 mm - same | LCC, 9.7x10 mm - same | LCC, 9.7x10 mm - same |
| Reference Oscillator | TCXO | XTAL (crystal) | TCXO | TCXO |
| Tracking Sensitivity | -167 dBm | -164 dBm | -167 dBm | -167 dBm |
| Firmware Type | ROM (SPG 5.10) | ROM | Flash (field-upgradeable) | ROM |
| Reel Quantity | 500 (reel B1) | 500 | 500 | 1000 (reel A3) |
| Constellation Set | GPS+GLONASS+Galileo+BeiDou | GPS+GLONASS+Galileo+BeiDou | GPS+GLONASS+Galileo+BeiDou | GPS+GLONASS+Galileo+BeiDou |
| Continuous Tracking Power | <25 mW | <25 mW | <25 mW | <25 mW |
Ключевые отличия
- Integrated TCXO for fastest warm-start time (против MAX-M10M-00B)
- Highest tracking sensitivity in MAX-M10 family (против MAX-M10M-00B)
- Integrated SAW filter blocks cellular/Wi-Fi interferers (против Quectel L76-L (cross-brand functional substitute))
Заметки по проектированию
The MAX-M10S-00B draws under 25 mW in continuous tracking mode at 3.3 V VCC. Place a 1 uF X7R ceramic + 100 nF decoupling pair within 3 mm of the VCC pad, and a 10 uF bulk capacitor if the host supply rail has >50 mV peak-to-peak ripple. The V_BCKP backup domain should be sourced from a coin cell (CR2032) or supercapacitor (>=0.1 F) to retain ephemeris across primary power cycles - this reduces warm-start TTFF from tens of seconds to a few seconds. The VCC and V_BCKP pins have separate power-on-reset circuitry, so V_BCKP may be brought up before VCC. Estimated: continuous current is approximately 7.5 mA at 3.3 V (25 mW / 3.3 V); backup current is typically 15 uA per the MAX-M10S integration manual.
The LCC 9.7 x 10 mm land pattern requires a 50 ohm coplanar waveguide (with ground) trace from the RF_IN pad to the antenna connector or active-antenna feedline. Use a 0.5 mm wide trace on 0.2 mm FR-4 with the ground plane clearance tuned to your stackup; the SparkFun MAX-M10S Qwiic breakout is a useful layout reference. Place the antenna as far as possible from cellular modems, switching regulators, and high-speed digital buses. The GND pad beneath the module should be flooded with a continuous ground pour stitched with 0.3 mm vias on a 1 mm pitch for thermal and RF return paths. Avoid routing any digital signal traces beneath the module's RF_IN pad - keepout the entire antenna coplanar region.
The UART interface operates up to 921.6 kbps; if your host MCU is more than 50 mm from the module, add a series ferrite bead on TXD1/RXD1 to suppress common-mode noise from switching power supplies. The USB interface (USB_DP / USB_DN) requires 90 ohm differential impedance matching and should be routed as a length-matched differential pair; if USB is unused, leave both USB_DP and USB_DN pads floating - do not connect them to GND as this can increase power consumption. The TIMEPULSE output is a CMOS push-pull signal; route it as a short trace to the host timing reference input and add a 33 ohm series resistor for impedance matching if the trace exceeds 20 mm.
Do not assume the MAX-M10S-00B ships with 9600 baud UART - per the SparkFun community thread, some -00B modules ship with OTP firmware at 38400 baud instead. Query the CFG-UART1-BAUDRATE UBX register on first power-up before sending configuration commands, and configure your host serial port to the actual default. Do not connect USB_DP or USB_DN to anything other than a USB connector or leave them floating; tying them to VCC or GND can cause the USB PHY to enter an undefined state. Do not exceed VCC of 3.6 V (the absolute maximum is 3.6 V per the integration manual); a 3.7 V Li-ion cell directly on VCC will damage the module - use a 3.3 V LDO between the battery and VCC.
Информация о соответствии
RoHS compliant per u-blox product page. Consumer/industrial grade - not AEC-Q100 qualified. The MAX-M10S-00B is intended for battery-powered consumer, IoT, and asset-tracking applications, not automotive safety-critical deployments.
