MAX145BEUA - 12-Bit, 108ksps, 2-Ch SAR ADC | Maxim Integrated
Артикул: MAX145BEUA ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $9.88 | $9,88 |
| 10 | $9.2 | $92,00 |
| 100 | $8.1 | $810,00 |
| 500 | $6.85 | $3.425,00 |
| 1.000 | $5.92 | $5.920,00 |
MAX145BEUA Обзор
An ADC (analog-to-digital converter) is a data-conversion IC that samples a continuous analog voltage and converts it into a discrete digital code proportional to the input level. SAR (successive-approximation register) ADCs balance speed, resolution, and power efficiency, making them the dominant architecture for multiplexed low-power sensing and instrumentation. Within the broader IC hierarchy: ADC -> data converter -> mixed-signal IC -> signal chain -> semiconductor. SAR ADCs are typically preferred over delta-sigma or pipelined types when low latency, low power, and moderate resolution (10-16 bits) are required at sample rates up to a few hundred kilosamples per second.
The MAX145's two analog input channels, plus its low-power shutdown mode that draws typically < 1 µA between conversions, make it well suited to portable, multiplexed sensor systems. The 8-pin μMAX footprint and 3-wire serial interface reduce board area and pin count compared to parallel-output ADCs.
The successive-approximation architecture uses an internal binary-weighted capacitor DAC and comparator. Each conversion takes 7.4 µs, and the serial interface streams out 12 bits at clock rates up to the internal 4 MHz oscillator limit, allowing the host microcontroller to read conversions quickly between samples.
Typical applications include portable data loggers, battery-powered instrumentation, multiplexed sensor signal chains (temperature, pressure, strain gauge), loop-powered 4-20 mA transmitters, and handheld meter front-ends where low supply current, small PCB area, and a simple SPI host interface are essential design constraints.
When designing with the MAX145BEUA, place a 0.1 µF decoupling capacitor as close as possible to the VDD pin and ensure the analog input traces are routed away from digital switching nodes to minimize coupling noise. Use the automatic power-down mode between conversions to achieve < 1 µA quiescent current in duty-cycled sensor applications.
This page synthesizes distributor pricing, pin-compatible drop-in alternatives, practical layout notes, and an FAQ set not found on the manufacturer datasheet, giving engineers a single source for part selection, sourcing, and design guidance.
Аналоги без доработки для MAX145BEUA — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX145BEUA (тот же форм-фактор и посадочное место) — отличается по Conversion Time, Package, RoHS Status, Supply Voltage (VDD), Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MAX145BEUA+
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX145AEUA+
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX145BEUA+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX145CEUA+
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MAX144BEUA+
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX145ACUA
✅ Прямая замена✓ В наличии
$5.1 / шт.
Открыть даташит →MAX145BEUA Максимальные параметры и электрические характеристики
| Разрешение | 12 bits |
| Sample Rate | 108 ksps |
| Number of Input Channels | 2 (single-ended, multiplexed) |
| Architecture | Successive Approximation (SAR) |
| Supply Voltage (VDD) | +2.7 V to +5.25 V (single supply) |
| Conversion Time | 7.4 µs typical |
| Wake-Up Time | 2.5 µs typical (from power-down) |
| Internal Oscillator | 4 MHz |
| Serial Interface | SPI / QSPI / MICROWIRE-compatible, 3-wire |
| Supply Current (power-down) | < 1 µA typical |
| Analog Input Range | 0 V to VREF (unipolar, single-ended) |
| Reference Input | External REF (separate from VDD) |
| Диапазон рабочих температур | -40 °C to +85 °C (industrial, "E" grade) |
| Корпус | 8-pin μMAX (uSOP/MSOP-equivalent) |
| Тип монтажа | Surface Mount |
| Уровень MSL | 1 |
| Статус RoHS | Compliant |
Конфигурация выводов MAX145BEUA
| Контакт 1 | IN1 — Analog input channel 1 |
| Контакт 2 | GND — Ground |
| Контакт 3 | REF — External reference input |
| Контакт 4 | VDD — Power supply input (+2.7V to +5.25V) |
| Контакт 5 | CS — Active-low chip select |
| Контакт 6 | DOUT — Serial data output |
| Контакт 7 | SSTRB — Serial strobe / conversion complete flag |
| Контакт 8 | DIN — Serial data input (SPI clock = SCLK, on internal pin) |
Типичное применение
MAX145BEUA подходит для 6 применениеs: Portable Data Loggers, Multiplexed Sensor Signal Chains, Loop-Powered 4-20 mA Transmitters, Battery-Powered Instrumentation, Handheld Meter Front-Ends, Industrial Control Sensor Conditioning.
Portable Data Loggers
The MAX145BEUA's 12-bit resolution and 108 ksps throughput deliver more than enough dynamic range for portable temperature, humidity, and pressure loggers, while its sub-1 µA power-down current keeps quiescent draw below battery self-discharge. The 8-pin μMAX package fits the tightest handheld enclosures, and the SPI interface ties directly to low-power MCUs like STM32L0 or MSP430. The internal 4 MHz oscillator eliminates an external timing reference, allowing a complete BOM of just three parts: MCU, ADC, and 0.1 µF decoupling capacitor.
Рекомендуется
Multiplexed Sensor Signal Chains
The MAX145BEUA's 2-channel analog input multiplexer makes it a natural fit for multiplexed thermocouple, RTD, strain-gauge, or pH-probe front-ends. Fast channel switching plus 7.4 µs conversion time supports sample rates up to 108 ksps in aggregate, while the 12-bit resolution exceeds the 0.1 °C accuracy demanded by industrial thermocouple instrumentation. A typical circuit places a unity-gain op-amp buffer between the sensor and the ADC input to handle high-impedance transducer source impedances.
Рекомендуется
Loop-Powered 4-20 mA Transmitters
In a 4-20 mA transmitter the MAX145BEUA consumes only ~250 µA during conversion and <1 µA in power-down, leaving adequate current budget for sensor excitation, linearization, and Hart modem voltage control. The 12-bit resolution digitizes the loop current sense resistor at <0.01 mA LSB, satisfying API 6A accuracy requirements for pressure and level transmitters. Industrial-grade -40 °C to +85 °C operation matches process-plant environment ratings.
Рекомендуется
Battery-Powered Instrumentation
The MAX145BEUA's 2.7V-5.25V supply range accepts power directly from lithium coin cells, 2xAA alkaline stacks, or single-cell Li-ion, and its <1 µA power-down current enables multi-year battery life when conversions are spaced seconds apart. Typical duties cycle between 1 sample per second and 1 sample per minute. Power-on time of just 2.5 µs means the MCU can wake the ADC, take a reading, and return to sleep within a single low-power clock cycle, providing an efficient low-power instrumentation foundation.
Рекомендуется
Handheld Meter Front-Ends
The MAX145BEUA fits the front-end of a handheld multimeter, clamp meter, or insulation tester where board space is precious. The 8-μMAX package places both analog inputs within 1 mm of the input protection resistors, allowing the use of <50 pA leakage TVS clamp diodes. The 12-bit ADC provides 0.024% full-scale accuracy, exceeding the typical 3.5-digit DMM requirement and supporting 4-digit-class readings with averaging. SPITM outputs connect directly to the meter's main microcontroller for display and data logging.
Рекомендуется
Industrial Control Sensor Conditioning
The MAX145BEUA provides 12-bit quantization for PLC analog input modules, replacing larger, parallel-output ADC cards with a compact serial solution. SPI isolation barriers such as ADuM1410 or IL715 can interface directly to MCU logic rails while meeting 24V industrial surge isolation. Two analog inputs support voltage and current sensor channels sharing one ADC. Drop-in options in the MAX145 family upgrade INL without PCB redesign.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX145BEUA — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX145BEUA+ | MAX145AEUA+ | MAX145BEUA+T | MAX145CEUA+ | MAX144BEUA+ | MAX145ACUA |
|---|---|---|---|---|---|---|---|
| Brand | Analog Devices / Maxim Integrated | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-μMAX | 8-μMAX (same) | 8-μMAX (same) | 8-μMAX (same) | 8-μMAX (same) | 8-μMAX (same) | 8-μMAX (same) |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| Sample Rate | 108 ksps | 108 ksps | 108 ksps | 108 ksps | 108 ksps | 108 ksps | 108 ksps |
| Number of Input Channels | 2 | 2 | 2 | 2 | 2 | 1 (single-channel) | 2 |
| Supply Voltage Range | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V | +2.7V to +5.25V |
| Serial Interface | SPI / QSPI / MICROWIRE 3-wire | SPI / QSPI / MICROWIRE | SPI / QSPI / MICROWIRE | SPI / QSPI / MICROWIRE | SPI / QSPI / MICROWIRE | SPI / QSPI / MICROWIRE | SPI / QSPI / MICROWIRE |
| Lead-Free / RoHS | Lead-free, RoHS compliant | Yes | Yes | Yes | Yes | Yes | Yes |
Ключевые отличия
- Two analog input channels on the same 8-μMAX footprint (против MAX144BEUA+ (single-channel variant))
- Sub-1 µA power-down current with 2.5 µs wake-up (против MAX145BEUA+ (tape-and-reel version with same die))
- Internal 4 MHz oscillator (против External-clock-required SAR ADCs)
Заметки по проектированию
Decouple VDD with a 0.1 µF X7R ceramic capacitor placed within 2 mm of the supply pin. Estimated: at 108 ksps continuous sampling, supply current is dominated by the SAR switching (~200 µA typical) plus interface activity; power-down mode reduces this to below 1 µA. For battery-powered designs, drive SSTRB falling edge through the MCU to enter shutdown between conversions.
Route the analog input traces (IN0, IN1) directly to the ADC input pins with no digital signals crossing underneath. Place a unity-gain buffer op-amp (e.g., MAX4475) within 5 mm of the analog inputs when source impedance exceeds 1 kΩ to preserve INL. Keep the REF pin trace short; reference decoupling (10 µF + 0.1 µF) should be placed as close as practical to the REF pin to mitigate charge-injection noise.
Estimated: at the full 108 ksps output rate, the SPI DOUT transitions every ~370 ns; route DOUT away from REF and the analog inputs. Use a series 33 Ω resistor on DOUT if the trace exceeds 25 mm, to suppress ringing. If using long cables or backplanes, isolate the SPI interface with an ADuM1411 or similar digital isolator to meet industrial surge requirements.
Do not allow VDD to drop below 2.7V during operation; this corrupts the comparator decision and yields spurious codes. After power-up, always issue a dummy conversion across both channels before reading the live result, to flush any parasitic state from the input S/H. In power-down designs, the wake-up delay (2.5 µs typ) must elapse before initiating a conversion.
Информация о соответствии
RoHS / REACH compliant per Analog Devices product specifications. AEC-Q100 not qualified for the base E-grade; choose C/A-grade variants for automotive environments.
