MAX232CPE - 5V RS-232 Transceiver, 2 Driver/2 Receiver, 16-PDIP
Артикул: MAX232CPE ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $3.42 | $3,42 |
| 10 | $3.08 | $30,80 |
| 100 | $2.74 | $274,00 |
| 500 | $2.45 | $1.225,00 |
| 1.000 | $2.18 | $2.180,00 |
MAX232CPE Обзор
An RS-232 transceiver is a line driver/receiver IC that converts between transistor-transistor logic (TTL/CMOS) voltage levels used by microcontrollers and the higher-voltage bipolar signaling levels defined by the EIA/TIA-232 standard. As a member of the line-driver/receiver IC class within Interface ICs, the MAX232 family uses external charge-pump capacitors (typically 1 µF to 10 µF) to double and invert the 5V supply, producing the ±10V swing required by RS-232. This topology removes the legacy dependence on ±12V rails that earlier RS-232 implementations required.
Key features include two RS-232 drivers with ±9V output swing (typical), two RS-232 receivers with TTL/CMOS compatible outputs, an integrated dual charge pump requiring only four external 1 µF capacitors, low supply current of 8 mA typical, and an operating temperature range of 0°C to +70°C (commercial grade). The MAX232CPE differs from the higher-speed MAX232EPE (which extends to 250 kbps) and the wide-temperature MAX232AEPE (which extends to -40°C and adds 15 kV ESD protection on the driver outputs).
The MAX232 family uses a proprietary dual charge-pump architecture that converts +5V into +10V and -10V using only four external capacitors. The drivers meet the EIA/TIA-232E and V.28 specifications with minimum ±5V output swing into 3 kΩ loads, while the receivers accept ±25V inputs and present 5 kΩ input resistance to the line. The MAX232CPE ships in the 16-pin PDIP (PE) through-hole package with pinout identical to the MAX232EPE, MAX232AEPE, SP232ACP-L, and other industry-standard drop-in equivalents.
Typical applications include microcontroller UART-to-RS-232 level translation, industrial point-of-sale (POS) terminals, networking equipment console ports, embedded debug and programming interfaces, and legacy serial peripheral interconnects (modems, instrumentation, barcode scanners). The wide input tolerance of the receivers (±25V) tolerates mis-wiring and noisy RS-232 environments.
When designing with this device, place the four charge-pump capacitors as close as possible to the IC pins and use 1 µF (or larger) ceramic or tantalum types to maintain ±10V output levels. Verify that the data rate does not exceed 120 kbps, as the MAX232CPE is not designed for higher-speed operation; for that, select the MAX232EPE (250 kbps) or MAX232AEPE (200 kbps) variants.
This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical PCB layout guidance not collated in the original manufacturer datasheet.
Аналоги без доработки для MAX232CPE — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX232CPE (тот же форм-фактор и посадочное место) — отличается по Data Rate, Operating Temperature, Package, RoHS Status, Supply Voltage.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MAX232CPE+
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX232EPE
✅ Прямая замена✓ В наличии
$1.78 / шт.
Открыть даташит →MAX232AEPE
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX232N
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
SP232ACP-L
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ADM232A
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX232CPE Характеристики
| Функция | RS-232 Transceiver (2 Drivers / 2 Receivers) |
| Protocol | EIA/TIA-232E, V.28/V.24 |
| Напряжение питания | 4.5 V to 5.5 V (single 5 V supply) |
| Скорость передачи данных | 120 kbps |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Driver Output Voltage Swing | ±9 V typical (RS-232 load) |
| Receiver Input Voltage Range | ±25 V |
| Ток потребления | 8 mA typical |
| Charge Pump Capacitors | 4 x 1 µF external |
| Рабочая температура | 0°C to +70°C (commercial grade) |
| Корпус | 16-pin PDIP (PE) |
| Тип монтажа | Through-Hole |
| Статус RoHS | See compliance_info |
Конфигурация выводов MAX232CPE
| Контакт 1 | C1+ — Charge-pump capacitor 1 positive terminal |
| Контакт 2 | V+ — Charge-pump +10V output |
| Контакт 3 | C1- — Charge-pump capacitor 1 negative terminal |
| Контакт 4 | C2+ — Charge-pump capacitor 2 positive terminal |
| Контакт 5 | C2- — Charge-pump capacitor 2 negative terminal |
| Контакт 6 | V- — Charge-pump -10V output |
| Контакт 7 | T2OUT — RS-232 driver 2 output |
| Контакт 8 | R2IN — RS-232 receiver 2 input |
| Контакт 9 | R2OUT — TTL/CMOS receiver 2 output |
| Контакт 10 | T1IN — TTL/CMOS driver 1 input |
| Контакт 11 | T1OUT — RS-232 driver 1 output |
| Контакт 12 | R1IN — RS-232 receiver 1 input |
| Контакт 13 | R1OUT — TTL/CMOS receiver 1 output |
| Контакт 14 | GND — Ground |
| Контакт 15 | VCC — +5V supply |
| Контакт 16 | NC — Not connected (per datasheet) |
Типичное применение
MAX232CPE подходит для 6 применениеs: Microcontroller UART-to-RS-232 Level Translation, Industrial Point-of-Sale (POS) Terminal Serial Ports, Networking Equipment Console / Management Port, Embedded Debug and Programming Interfaces, Legacy Modem and Instrumentation Interconnect, Automotive Diagnostics (OBD-II) Serial Bridges.
Microcontroller UART-to-RS-232 Level Translation
The MAX232CPE converts the 0V-5V UART (TTL/CMOS) logic levels of a microcontroller to the ±5V minimum-swing RS-232 levels required by a host PC or serial terminal. Two drivers and two receivers handle the standard TX/RX plus RTS/CTS handshaking lines on a DB9 connector. With on-chip charge pumps, no negative supply rail is needed - only a single +5V rail and four 1 µF capacitors. Data rate is achieved via 120 kbps, which exceeds all common baud rates up to 115200.
Рекомендуется
Industrial Point-of-Sale (POS) Terminal Serial Ports
POS terminals, receipt printers, barcode scanners, and cash drawers historically communicate over RS-232 to the host register. The MAX232CPE's ±25V receiver input tolerance survives the ground-potential differences and ESD transients common in retail and warehouse environments. Operating temperature 0°C to +70°C covers the indoor commercial range. The 16-PDIP through-hole package is also easy to hand-rework and replace in field service scenarios.
Рекомендуется
Networking Equipment Console / Management Port
Routers, switches, firewalls, and base stations expose a console (RJ45-to-DB9 serial) port for out-of-band management using RS-232 logic levels. The MAX232CPE accepts the router's UART TX and translates it to ±5V RS-232 for the management workstation. The 16-pin PDIP fits legacy console-board designs; industrial temperature tolerance and ±15 kV ESD may require upgrading to MAX232AEPE for outdoor cabinets or noisy electrical environments.
Рекомендуется
Embedded Debug and Programming Interfaces
Development boards for 8051, AVR, PIC, MSP430, and similar microcontrollers expose an RS-232 serial debug port for bootloaders and in-system programming. The MAX232CPE converts the 3.3V or 5V UART signals to RS-232 levels expected by legacy PC COM ports. The DIP package is breadboard-friendly for prototyping. Many modern designs are migrating to USB, but the MAX232CPE still appears in millions of legacy debug boards and educational kits.
Рекомендуется
Legacy Modem and Instrumentation Interconnect
Industrial instrumentation, laboratory equipment, and legacy modems present RS-232 ports at DB25 or DB9 connectors with ±5V minimum signal swing. The MAX232CPE interfaces these legacy peripherals to a modern microcontroller or single-board computer with a UART. With ±25V tolerant receivers, the IC survives mis-wiring and AC-coupled noise on long cable runs typical of factory-floor installations.
Рекомендуется
Automotive Diagnostics (OBD-II) Serial Bridges
OBD-II scan tools, ECU programmers, and aftermarket vehicle diagnostic interfaces historically used RS-232 to connect to a laptop. The MAX232CPE provides the level translation between the diagnostic MCU's UART and the OBD-II cable, with the receiver's ±25V tolerance absorbing vehicle electrical noise. For under-hood or extreme-temperature automotive environments, upgrade to the industrial-grade MAX232AEPE (-40°C to +85°C).
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX232CPE — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX232CPE+ | MAX232EPE | MAX232AEPE | MAX232N | SP232ACP-L | ADM232A |
|---|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | MaxLinear | Analog Devices |
| Package | 16-PDIP (PE) | 16-PDIP (PE) - same | 16-PDIP (PE) - same | 16-PDIP (PE) - same | 16-PDIP - same | 16-PDIP - same | 16-PDIP - same |
| Data Rate | 120 kbps | 120 kbps | 250 kbps | 200 kbps | 120 kbps | 120 kbps | 200 kbps |
| Operating Temperature | 0°C to +70°C | 0°C to +70°C | 0°C to +70°C | -40°C to +85°C | 0°C to +70°C | 0°C to +70°C | 0°C to +70°C |
| Supply Voltage | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V | 4.5V to 5.5V |
| Drivers / Receivers | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 | 2 / 2 |
| Lead-Free / RoHS | No (lead-free variant is MAX232CPE+) | Yes (RoHS) | No (lead-free variant is MAX232EPE+) | No (lead-free variant is MAX232AEPE+) | No (lead-free variant is MAX232N+) | Yes (RoHS, -L suffix) | Yes (RoHS) |
Ключевые отличия
- Industry-standard 16-PDIP pinout shared with multiple drop-in alternatives (против SP232ACP-L (MaxLinear))
- Higher data rate available in same package via MAX232EPE (против MAX232EPE)
- Industrial-grade upgrade path via MAX232AEPE (против MAX232AEPE)
Заметки по проектированию
Place four 1 µF charge-pump capacitors (C1 through C4) as close as possible to the MAX232CPE's C1+, C1-, C2+, C2-, V+, and V- pins. Use ceramic or low-ESR tantalum capacitors; polarized capacitors must be oriented with positive terminals to C1+/C2+. Use short PCB traces (under 5 mm) to minimize parasitic inductance on the charge-pump nodes. Decouple VCC with a 0.1 µF ceramic in parallel with the bulk supply capacitor.
Do not exceed 120 kbps data rate - for higher baud rates use the MAX232EPE (250 kbps) or MAX232AEPE (200 kbps). Do not apply voltage higher than ±25V to receiver inputs. Note that the standard MAX232CPE has a 0°C minimum operating temperature; for cold environments use MAX232AEPE. The MAX232CPE is leaded finish - order MAX232CPE+ (with '+' suffix) for RoHS-compliant end products.
Keep RS-232 trace lengths short and route them away from switching-noise sources such as DC-DC converters, oscillators, and clock lines. Place a 100 nF decoupling capacitor directly on VCC within 3 mm of pin 15. Add a small series ferrite bead or 10 Ω resistor on VCC for additional supply-noise isolation. The exposed through-hole pins of the 16-PDIP package allow easy rework and field replacement.
Информация о соответствии
MAX232CPE is supplied with lead finish (Pb); the RoHS-compliant equivalent is MAX232CPE+ (with '+' suffix). REACH compliance per manufacturer product page. Not AEC-Q100 qualified - not intended for automotive under-hood applications. Use MAX232AEPE for extended temperature or ESD-sensitive designs.
