MAX3232ECD - 250kbps Dual RS-232 Transceiver | Texas Instruments
Артикул: MAX3232ECD ✓ АктивенMAX3232ECD Обзор
An RS-232 transceiver is the physical-layer interface between a host controller or data-processing equipment and an RS-232 port. It combines a line driver, which converts logic-level signals into RS-232 voltage levels, with a receiver, which converts incoming RS-232 signals back into logic-compatible levels. In the power-management hierarchy of communication systems, the MAX3232ECD provides bidirectional RS-232 signal conditioning between a UART controller and an external connector.
Key operating features include two communication channels, a 3 V to 5.5 V supply range, and a maximum data rate of 250 kbps. The ±15-kV IEC ESD protection improves robustness when cables and connectors are exposed to electrostatic discharge. These characteristics make the device suitable for industrial control equipment, data acquisition systems, service interfaces, and legacy peripheral connections where a modern USB interface is not practical.
The MAX3232 family uses charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 from a single low-voltage supply. This allows the transceiver to operate from 3 V to 5.5 V instead of requiring the traditional ±12 V RS-232 supply. The manufacturer identifies the MAX3232 as a dual-channel 250-kbps line driver and receiver, while its comparison materials identify the MAX3232E as an improved direct drop-in replacement for the MAX3232.
Typical applications include UART-to-RS-232 conversion in industrial controllers, programming and configuration ports in test equipment, service interfaces for embedded systems, and point-to-point links between computers or controllers and RS-232 equipment. Using one transceiver supports two RS-232 channels, allowing transmit and receive signals to share the same physical interface without requiring separate driver and receiver packages.
The primary design consideration is ensuring that external cable transients remain within the device's operating and protection limits. Keep RS-232 traces away from sensitive clocks and data lines, provide a low-impedance ground return, and use the device pin descriptions in the manufacturer datasheet when assigning PCB functions. Power-supply bypassing and charge-pump capacitor placement should follow the datasheet's recommended layout to maintain stable operation and minimize coupling into adjacent circuitry.
This product page combines the MAX3232ECD's electrical characteristics, package information, verified manufacturer resources, drop-in alternatives, comparison guidance, and practical interface-design notes. It is intended to help engineers confirm electrical compatibility, identify the correct 16-SOIC replacement, and plan PCB implementation before releasing a new RS-232 design.
Аналоги без доработки для MAX3232ECD — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX3232ECD (тот же форм-фактор и посадочное место) — отличается по Package, ESD Protection, External Capacitors, Function, Protocol Compliance.
MAX3232EIPWG4
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3232EIDR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX3232EIDBG4
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX3232ECDR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TRS3232EIRGT
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3232ECD Характеристики
| Product Type | Dual RS-232 line driver and receiver |
| Number of Channels | 2 channels |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV IEC ESD protection |
| Interface Standard | RS-232 |
| Transceiver Configuration | 2 transmit and 2 receive functions |
| Корпус | 16-pin SOIC |
| Тип монтажа | Surface mount |
| Supply Topology | Single 3 V to 5.5 V supply |
| ESD Test Method | IEC 61000-4-2 contact and air-gap discharge |
| TIA/EIA Compliance | Meets or exceeds TIA/EIA-232-F requirements |
Руководство по цоколевке MAX3232ECD в корпусе 16-pin soic
Цоколевка для MAX3232ECD (корпус 16-pin soic). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX3232ECD.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX3232ECD подходит для 6 применениеs: Industrial UART-to-RS-232 Interfaces, Test and Measurement Equipment, Embedded System Service Ports, Data Acquisition Equipment, Legacy Peripheral Connectivity, Point-to-Point Serial Links.
Industrial UART-to-RS-232 Interfaces
The MAX3232ECD fits industrial controller and data-acquisition equipment that must translate between a local UART and an external RS-232 connection. Its two-channel arrangement supports bidirectional communications without separate line-driver and receiver packages. The 3 V to 5.5 V operating range simplifies integration with modern low-voltage control logic, while the maximum 250-kbps data rate accommodates common legacy serial protocols. The ±15-kV IEC ESD protection adds interface robustness where an RS-232 cable may connect to external equipment. Keep the transceiver ground connected to the equipment ground and follow the manufacturer layout for the required charge-pump and bypass capacitors.
Рекомендуется
Test and Measurement Equipment
The MAX3232ECD is useful in test instruments that retain an RS-232 service port for configuration, diagnostics, or legacy data logging. A single device provides both driver and receiver paths for communicating with a PC or terminal, while its 250-kbps maximum rate is suitable for many low-speed instrument-control protocols. Operating from 3 V to 5.5 V allows the interface to share a compact instrument power rail. The ±15-kV IEC ESD protection is especially relevant when users repeatedly connect service cables. Maintain a common signal ground between the instrument and connected equipment, and place the required capacitors close to the transceiver pins according to the manufacturer guidance.
Рекомендуется
Embedded System Service Ports
The MAX3232ECD can provide a service and update connection for embedded control boards that retain an RS-232 interface. The dual-channel structure allows one channel to transmit configuration commands and another to receive status or firmware data, depending on the connector wiring. Its 250-kbps signaling rate supports conventional UART traffic, and operation from 3 V to 5.5 V is compatible with embedded supply levels commonly used for digital logic. The ESD-protected bus pins improve resilience during service connections. Designers should use a dedicated connector ground, avoid long parallel stubs, and verify the exact signal mapping against the manufacturer pin-description table.
Рекомендуется
Data Acquisition Equipment
The MAX3232ECD is appropriate for data-acquisition systems that send measurement records or control commands to a host computer through RS-232. Supporting two channels permits simultaneous command transmission and response reception, while the maximum 250-kbps rate is suitable for many laboratory and industrial logging protocols. The low-voltage 3 V to 5.5 V supply range simplifies integration with compact acquisition hardware. For reliable laboratory use, route the RS-232 cable away from sensitive analog inputs and maintain a low-impedance ground return. Use the manufacturer application circuit and pin definitions to place bypass and charge-pump capacitors correctly.
Рекомендуется
Legacy Peripheral Connectivity
The MAX3232ECD allows modern control electronics to communicate with legacy RS-232 peripherals that cannot use USB or a network interface. Its integrated driver and receiver functions reduce the number of external interface components, while the 250-kbps maximum data rate aligns with many legacy serial devices. The 3 V to 5.5 V operating range permits operation from low-voltage system rails without a separate ±12 V source. The ±15-kV IEC ESD protection helps protect the electronics behind the connector. Confirm the peripheral's logic levels, connector pinout, and ground arrangement before connecting it, because older equipment may use nonstandard wiring.
Рекомендуется
Point-to-Point Serial Links
The MAX3232ECD is suited to short point-to-point RS-232 links between two pieces of equipment, such as a controller and a peripheral or a terminal and a diagnostic instrument. The two-channel architecture supports full-duplex communication when the transmitter and receiver paths are assigned appropriately. A maximum data rate of 250 kbps accommodates many asynchronous serial protocols, and the 3 V to 5.5 V supply range simplifies board-level integration. The ±15-kV IEC ESD protection improves interface survivability. Maintain a shared ground reference, use twisted-pair wiring where practical, and confirm that the installed cable and connector satisfy the applicable RS-232 distance limitations.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX3232ECD — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX3232E | MAX3232EIDR | MAX3232EIDBG4 | MAX3232ECDR | TRS3232E |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Manufacturer Replacement Guidance | MAX3232 baseline family | Improved direct drop-in replacement for MAX3232 | MAX3232E family ordering variant | MAX3232E family ordering variant | MAX3232C family ordering variant | Included in the manufacturer comparison with MAX3232 and MAX3232E |
Ключевые отличия
- Manufacturer-recommended enhanced family (против MAX3232E)
- Integrated dual-channel RS-232 interface (против TRS3232E)
- Defined 250-kbps operation and IEC ESD protection (против MAX3232E)
- Same-package procurement flexibility (против MAX3232ECDR)
Заметки по проектированию
Place the charge-pump capacitors and supply-bypass components at the locations shown in the manufacturer application circuit. Keep the RS-232 driver and receiver routes away from clocks, reset lines, precision analog inputs, and high-impedance sensor nodes. A common ground connection between the transceiver and the RS-232 connector is required because RS-232 signal voltages are referenced to the interface ground.
Do not treat family compatibility as proof that every ordering suffix is interchangeable. Before substituting MAX3232E, MAX3232EIDR, MAX3232EIDBG4, MAX3232ECDR, or TRS3232E, compare the complete ordering table, temperature grade, package dimensions, pin configuration, data rate, and ESD rating. Preserve the exact MPN in production documentation to avoid an unintended temperature-grade or packaging change.
Use a ground conductor with the RS-232 cable, route the cable away from switching nodes and high-speed digital traces, and minimize stub lengths between the transceiver and connector. Although the MAX3232ECD includes ±15-kV IEC ESD protection, the protection is not a substitute for controlled cable routing, connector selection, grounding, or shielding in electrically noisy industrial environments.
Decouple the 3 V to 5.5 V supply at the transceiver and follow the manufacturer capacitor values and placement. Keep the supply return path short and continuous through the exposed board layers. Because RS-232 drivers use charge-pumped rails, incorrect capacitor connections or placement can increase supply disturbance and reduce interface reliability; use the datasheet's recommended application schematic as the layout reference.
Информация о соответствии
The technical product material identifies IEC 61000-4-2 ESD protection and TIA/EIA-232-F interface performance, but it does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for the exact MAX3232ECD ordering suffix. Confirm these attributes in the manufacturer's ordering or compliance documentation.