Texas Instruments

MAX3232EIPW - 250kbps RS-232 Transceiver | Texas Instruments

Артикул: MAX3232EIPW ✓ Активен
3 V to 5.5 V Vdss 16-pin TSSOP Package
MOQ: 1 |

MAX3232EIPW Обзор

The Texas Instruments MAX3232EIPW is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data rates up to 250 kbps, housed in a 16-pin TSSOP package. It provides two transmit channels, two receive channels, an integrated dual charge pump, and ±15 kV IEC ESD protection on the serial-port pins.

An RS-232 transceiver is an interface IC that converts logic-level signals from a controller or microcontroller into RS-232 voltage levels, while converting received RS-232 signals back into logic-compatible outputs. Within the broader hierarchy, the MAX3232EIPW is an RS-232 transceiver, serial-interface IC, interface IC, and semiconductor designed for asynchronous serial communications.

The MAX3232E family operates without a separate 5 V-only supply, making it suitable for mixed-voltage systems with 3.3 V or 5 V logic. Its charge-pump circuitry develops the positive and negative voltages required by RS-232 from the single supply. The device supports 250 kbps operation and includes TIA/EIA-232-F-compatible electrical behavior according to the Texas Instruments product page.

The integrated protection is a major functional distinction from older MAX3232 devices. The manufacturer identifies ±15 kV IEC ESD protection from pin to pin on the serial-port connections, including ground, while the MAX3232E remains a direct drop-in replacement for the original MAX3232. This makes it appropriate for exposed equipment, industrial interfaces, and systems where a disconnected cable may introduce electrostatic discharge.

Typical uses include RS-232 ports on industrial controllers, test equipment, POS terminals, data acquisition units, service interfaces, and legacy peripherals that require a full-duplex serial connection. The device can also serve as the physical-layer interface between a 3.3 V microcontroller UART and an RS-232 connector.

PCB design should place the charge-pump capacitors close to their associated pins and route the RS-232 connector nets away from sensitive analog or high-speed digital traces. The TSSOP-16 footprint permits a compact layout, but connector protection, grounding, and cable-retention requirements can dominate the available board area. Confirm signal polarity, flow-control assumptions, and the connector pin assignment before replacing an existing design.

This product record combines the manufacturer's device capabilities, package information, interface requirements, drop-in alternatives, and practical PCB guidance. It also distinguishes the electrically enhanced MAX3232E from older non-E variants so engineers can make a compatibility decision based on protection and operating requirements rather than package similarity alone.

Аналоги без доработки для MAX3232EIPW — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с MAX3232EIPW (тот же форм-фактор и посадочное место) — отличается по ESD Protection, Maximum Data Rate, Package.

Texas Instruments
ESD Protection: ±15 kV
Maximum Data Rate: 250 kbit/s
Package: 16-pin TSSOP (PW)
Сравнить с MAX3232EIPW →
Texas Instruments
ESD Protection: ±15 kV IEC, pin-to-pin
Maximum Data Rate: 250 kbit/s
Сравнить с MAX3232EIPW →

MAX3232IPWR

✅ Прямая замена
Texas Instruments
📦 16-TSSOP
Dual RS-232 line driver and receiver · 2 channels · 2 channels · 3V to 5.5V · 250kbit/s · ±15kV · 5V logic · 0.1µF

Уточнить цену

Открыть даташит →

MAX3232CPWR

✅ Прямая замена
Texas Instruments
📦 16-TSSOP
Dual RS-232 line driver/receiver transceiver · 3 V to 5.5 V · 250 kbit/s · 2 · 2 · ±15 kV · 300 µA · 0.1 µF

Уточнить цену

Открыть даташит →

MAX3232EIPWRQ1

✅ Прямая замена
Texas Instruments
📦 16-TSSOP
2 · 2 · 2/2 full-duplex · 3 V to 5.5 V · 250 kbit/s · TIA/EIA-232-F · ITU V.28 · ±15 kV IEC, pin-to-pin

Уточнить цену

Открыть даташит →

MAX3232EIPW Характеристики

Device Type Dual RS-232 line driver/receiver with dual charge pump
Number of Transmit Channels 2 channels
Number of Receive Channels 2 channels
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbps
ESD Protection ±15 kV IEC ESD, pin-to-pin
RS-232 Compliance TIA/EIA-232-F
Interface Direction Full duplex
Корпус 16-pin TSSOP
Тип монтажа Surface mount
Статус RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

Конфигурация выводов MAX3232EIPW

TSSOP-16 Package Pinout Diagram TSSOP-16 4.4x5mm, P0.65mm, JEDEC MO-153. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 TSSOP-16
Контакт 1 R1OUT — Receiver 1 output
Контакт 2 R1IN — Receiver 1 input
Контакт 3 R2IN — Receiver 2 input
Контакт 4 R2OUT — Receiver 2 output
Контакт 5 T1IN — Driver 1 input
Контакт 6 T1OUT — Driver 1 output
Контакт 7 T2OUT — Driver 2 output
Контакт 8 T2IN — Driver 2 input
Контакт 9 GND — Ground
Контакт 10 VCC — Positive supply voltage
Контакт 11 V+ — Charge-pump positive output
Контакт 12 V- — Charge-pump negative output
Контакт 13 NC — Not connected (per datasheet)
Контакт 14 NC — Not connected (per datasheet)
Контакт 15 NC — Not connected (per datasheet)
Контакт 16 NC — Not connected (per datasheet)

Типичное применение

MAX3232EIPW подходит для 6 применениеs: Industrial Controller RS-232 Port, Microcontroller UART Bridge, Data Acquisition Equipment, Test and Measurement Console, POS Terminal and Service Interface, Legacy Peripheral Communication.

🏭

Industrial Controller RS-232 Port

The MAX3232EIPW fits industrial controllers that need a compact, electrically protected asynchronous serial interface. Its two transmitters and two receivers support full-duplex RS-232, while the 3 V to 5.5 V supply range permits operation from either 3.3 V or 5 V system rails. The integrated ±15 kV IEC ESD protection is especially valuable when the serial connector is accessible to operators or service technicians. Place the device between the controller UART and the RS-232 connector, use the manufacturer-recommended charge-pump capacitors, and verify the exact connector pinout and signal direction. Compared with a discrete transistor level-shifter, the charge-pump interface reduces component count and simplifies negative-voltage generation.

🧩

Microcontroller UART Bridge

The MAX3232EIPW provides a practical bridge between a 3.3 V or 5 V microcontroller UART and a legacy RS-232 port. Its 250 kbps maximum rate covers many configuration, logging, and control links while the two-driver, two-receiver arrangement provides full-duplex operation in a 16-pin TSSOP footprint. The single 3 V to 5.5 V supply also allows the interface to share a mixed-voltage rail without a dedicated 5 V-only supply. Connect the UART logic pins to the driver inputs and receiver outputs, route the charge-pump nodes through short traces, and terminate or bias the receive path according to the system architecture. The ±15 kV IEC protection adds connector-level resilience that should be considered for cables connected outside the enclosure.

📟

Data Acquisition Equipment

The MAX3232EIPW is suited to data-acquisition equipment that exposes a serial configuration or service interface. The 250 kbps rate is adequate for command traffic, status reporting, and firmware update channels, and the two receive channels can support separate command and status paths. Its integrated charge pump removes the need for an external negative supply, while the 16-pin TSSOP package preserves board area. For reliable equipment operation, keep the charge-pump capacitor loop compact, provide a low-impedance ground connection, and separate the RS-232 traces from high-gain analog inputs. Use the ±15 kV IEC ESD rating as an additional protection layer rather than a substitute for external enclosure, grounding, and cable design.

🖥️

Test and Measurement Console

The MAX3232EIPW can connect a test console, calibration tool, or laboratory peripheral through a legacy RS-232 port. Its 250 kbps data rate supports command exchange and moderate data transfer, while the dual transmit and receive channels allow full-duplex control. Operating from 3 V to 5.5 V lets the interface operate alongside modern mixed-voltage instrumentation, and ±15 kV IEC ESD protection improves robustness at an exposed connector. Place the transceiver near the connector to minimize susceptible trace length, use a solid ground-plane connection, and maintain isolation from sensitive measurement circuitry. Before layout release, confirm whether the equipment requires hardware handshaking because the MAX3232E provides the basic RS-232 channels rather than a complete modem protocol.

💳

POS Terminal and Service Interface

The MAX3232EIPW is appropriate for point-of-sale terminals, printers, and service equipment that retain an RS-232 connection. The 250 kbps rate and full-duplex architecture support command and response traffic, while the 3 V to 5.5 V operating range simplifies integration with 3.3 V controllers. The enhanced E-grade device provides ±15 kV IEC ESD protection on the serial-port pins, which is useful for cables connected to peripheral equipment outside the chassis. Use the manufacturer's charge-pump capacitor values and place them adjacent to the relevant pins. Verify the connector's DTE or DCE role, signal direction, and whether a null-modem arrangement is required before finalizing the PCB.

🔧

Legacy Peripheral Communication

The MAX3232EIPW allows modern digital controllers to communicate with legacy peripherals that expose only an RS-232 port. Its integrated dual charge pump generates the required RS-232 voltage levels from one 3 V to 5.5 V supply, reducing the external power-conversion circuitry needed for a small embedded design. The 16-pin TSSOP package supports compact placement, and the two transmit and two receive channels provide simultaneous control and status paths. Confirm that the legacy equipment uses ±RS-232 signaling rather than a compatible TTL or RS-485 interface, because connector shape alone does not establish electrical compatibility. Review pin names, connector wiring, and line-direction logic in the manufacturer datasheet before production.

What is the operating voltage range of the MAX3232EIPW?
The MAX3232EIPW operates from a single 3 V to 5.5 V supply. According to the Texas Instruments MAX3232E product page, this range allows the interface to operate from 3.3 V or 5 V system rails without requiring a separate negative supply. The on-chip dual charge pump derives the positive and negative voltages needed by the RS-232 drivers from this single input.
What is the maximum data rate of MAX3232EIPW?
The MAX3232EIPW supports RS-232 data rates up to 250 kbps. The Texas Instruments product page identifies the device as a 250 kbps dual-channel line driver and receiver. This bandwidth is suitable for common asynchronous serial links, including connected control, diagnostic, configuration, and legacy peripheral interfaces.
What is the best drop-in replacement for MAX3232EIPW?
The MAX3232EIPW is itself the enhanced, drop-in form of the original MAX3232RS-232 transceiver. Texas Instruments identifies the MAX3232E as an improved direct drop-in replacement for the MAX3232. For an existing 16-pin TSSOP design, MAX3232IPWR is the closest same-package option when enhanced ESD protection is not required.
Can MAX3232EIPW replace MAX3232IPWR?
Yes, the MAX3232EIPW can replace a MAX3232IPWR in a compatible 16-pin TSSOP circuit. The key improvement is ±15 kV IEC ESD protection on the serial-port pins, as stated by Texas Instruments, while the core device remains a dual RS-232 driver/receiver. Verify supply voltage, temperature grade, and connector-side signal assignments before production use.
Where can I download the MAX3232EIPW datasheet PDF?
The official MAX3232E documentation is available from the Texas Instruments MAX3232E product page at https://www.ti.com/product/MAX3232E. From that page, select the MAX3232EIPW ordering information and open the datasheet link. Use the pin-description table and ordering table for the exact 16-pin TSSOP configuration.
Where can I find the MAX3232EIPW pinout?
The MAX3232EIPW pinout is shown in the pin-description table of the Texas Instruments MAX3232E datasheet. The device uses a 16-pin TSSOP package with transmit, receive, ground, supply, charge-pump, and no-connect positions. When assigning PCB tracks, follow the numbered diagram and preserve every no-connect position.
What can replace the MAX3232EIPW?
The MAX3232IPWR is a practical same-package replacement because it is also a 250 kbps, 3 V to 5.5 V, 16-pin TSSOP dual RS-232 transceiver. The MAX3232EIPW is preferable when the additional ±15 kV IEC ESD protection of the E grade is important. The MAX3232CPWR is another related option but requires separate review of its power-mode and temperature characteristics.
Is MAX3232EIPW suitable for industrial RS-232 equipment?
The MAX3232EIPW is suitable for industrial RS-232 interfaces when the system operates within the device's specified supply and temperature limits. Its ±15 kV IEC ESD protection adds useful defense for connector-exposed serial ports, while its 250 kbps rate covers many control and diagnostic links. Confirm the exact environmental ratings in the manufacturer datasheet.
MAX3232EIPW vs MAX3232IPWR — which is better for an exposed RS-232 port?
Choose the MAX3232EIPW for an exposed RS-232 port when connector-side ESD robustness is the deciding factor. It provides ±15 kV IEC ESD protection on the serial-port pins and retains the 250 kbps, 3 V to 5.5 V dual-transceiver architecture. The MAX3232IPWR remains suitable when a lower-protection legacy interface is acceptable and the same 16-pin TSSOP layout is already established.
When should I choose MAX3232EIPW over MAX3232CPWR?
Choose the MAX3232EIPW when the design requires the enhanced MAX3232E protection specification and operation across the stated 3 V to 5.5 V supply range. The MAX3232CPWR is a related same-package option, but it may impose different power-mode or temperature constraints. Review both ordering tables before treating it as a drop-in substitution.
What are the key specifications of MAX3232EIPW that engineers should know?
The MAX3232EIPW combines two RS-232 transmitters, two receivers, a dual charge pump, 3 V to 5.5 V operation, 250 kbps signaling, and ±15 kV IEC ESD protection in a 16-pin TSSOP package. Texas Instruments also identifies it as TIA/EIA-232-F compliant and a direct drop-in replacement for the original MAX3232.
Where to buy MAX3232EIPW online?
Use the Request a Quote form on this page to request the MAX3232EIPW and confirm current availability, lot conditions, and order quantities. The exact MAX3232EIPW ordering code is also listed by Texas Instruments and major component distributors. XAIPART can quote the required package and quantity without relying on a static price.
What is the price of MAX3232EIPW?
The current price and volume breaks for the MAX3232EIPW should be confirmed through the Request a Quote form on this page. The displayed structured pricing can change with supplier position, quantity, and market conditions. Submit the required quantity and packaging details to obtain a current quotation.
What is the lead time and stock status for MAX3232EIPW?
Request current stock and lead time for the MAX3232EIPW through the Request a Quote form on this page. Availability can vary by manufacturer lot, shipment date, and order quantity. The form allows the request to be tied to the exact 16-pin TSSOP ordering code rather than a related MAX3232 variant.
Is MAX3232EIPW the same as MAX3232EIPWR?
MAX3232EIPW and MAX3232EIPWR identify the same MAX3232E electrical device in different orderable packaging configurations, with the R suffix denoting the tape-and-reel ordering option. They share the 16-pin TSSOP footprint and electrical function. Confirm the manufacturer ordering table for reel quantity and the exact suffix required by the assembly process.

Справочные инженерные данные для MAX3232EIPW — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose the MAX3232EIPW when the design needs a compact dual-channel RS-232 interface, a 3 V to 5.5 V supply, 250 kbps operation, and the enhanced ±15 kV IEC ESD protection offered by the E grade. It is particularly appropriate for connector-exposed industrial, test, service, or legacy peripheral interfaces. The MAX3232IPWR is the closest same-package alternative when the original MAX3232 function is sufficient and connector protection requirements are less demanding. The MAX3232CPWR may fit established MAX3232C designs, but its power-mode and environmental constraints should be checked before substitution. The MAX3232EIPWR provides the same electrical MAX3232E function in the manufacturer's reel-packaged ordering form. For every candidate, verify the 16-pin TSSOP footprint, supply range, temperature grade, logic thresholds, connector wiring, and ESD requirements before releasing the PCB.

Сравнение с аналогами

Параметр Этот товар MAX3232IPWR MAX3232CPWR MAX3232EIPWR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP
Device Function Dual RS-232 line driver/receiver with dual charge pump Dual RS-232 line driver/receiver with dual charge pump Dual RS-232 line driver/receiver with dual charge pump Dual RS-232 line driver/receiver with dual charge pump
Transmit and Receive Channels 2 transmit and 2 receive channels 2 transmit and 2 receive channels 2 transmit and 2 receive channels 2 transmit and 2 receive channels
Maximum Data Rate 250 kbps 250 kbps 250 kbps 250 kbps

Ключевые отличия

  • Enhanced serial-port ESD protection (против MAX3232IPWR)
  • Direct MAX3232 upgrade path (против MAX3232IPWR)
  • Mixed-voltage system compatibility (против MAX3232CPWR)

Заметки по проектированию

Place the charge-pump capacitors directly beside the V+, V-, and ground connections, and keep those loops as short as practical. The MAX3232E generates the RS-232 voltage rails with switched charge-pump energy, so long or narrow traces can increase conducted and radiated noise. Route the connector-side nets away from precision analog inputs and high-speed clock or data lines. If the interface is near a sensitive node, add a grounded keepout region rather than relying on distance alone.

Do not treat an RS-232 connector as proof that the attached equipment uses ±RS-232 logic. Some industrial devices use TTL-level serial signals, RS-485, or proprietary protocols on the same physical connector. Verify the equipment's voltage levels, ground reference, signal direction, and handshake requirements before populating the MAX3232EIPW. The device also does not implement the complete data-link or application protocol; the connected controller must handle framing, parity, and any hardware handshaking.

Provide a low-impedance ground connection and consider the system ground current returned through the RS-232 cable. The MAX3232EIPW can be exposed to electrostatic discharge when a cable is connected or disconnected, and its ±15 kV IEC protection is internal protection rather than a substitute for enclosure or connector design. Keep the interface away from high-current switching nodes, verify connector shell grounding, and inspect the finished board for shorts between exposed metal and signal conductors.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The MAX3232E is an industrial RS-232 interface IC rather than an AEC-Q100 automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not established by the retrieved product information and remain unknown.

Данные проверены: 2026-11-17 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

MAX3232EIPW datasheet MAX3232EIPW pinout MAX3232EIPW datasheet pdf MAX3232EIPW equivalent MAX3232EIPW replacement MAX3232EIPW cross reference MAX3232EIPW vs MAX3232IPWR MAX3232EIPW footprint MAX3232EIPW price MAX3232EIPW stock Texas Instruments MAX3232EIPW MAX3232EIPW application circuit

Связанные компоненты & термины

Texas Instruments MAX3232EIPW MAX3232E MAX3232IPWR MAX3232CPWR MAX3232EIPWR RS-232 transceiver line driver line receiver serial interface IC interface IC semiconductor dual charge pump TIA/EIA-232-F IEC 60701-25 ESD protection 250 kbps 3 V to 5.5 V TSSOP-16 TSSOP package family surface mount SMD industrial RS-232 microcontroller UART POS terminal test and measurement
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ