MAX9675ECQ+ - 110MHz 16x16 Video Crosspoint Switch | Maxim Integrated
Артикул: MAX9675ECQ ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $9.85 | $9,85 |
| 10 | $8.9 | $89,00 |
| 100 | $7.65 | $765,00 |
| 500 | $6.42 | $3.210,00 |
| 1.000 | $5.2 | $5.200,00 |
MAX9675ECQ Обзор
A video crosspoint switch is an analog or digital signal-routing IC that allows any of N inputs to be switched to any of M outputs, typically with buffering on both sides so signals can drive long PCB traces or 75 ohm video loads. Crosspoint switches sit at the heart of video routers, production switchers, surveillance multiplexers, and broadcast equipment, replacing mechanical relays and discrete video amplifiers with a single silicon device. Programmable gain lets the designer compensate for cable losses or output-load variations across channels.
The MAX9675ECQ+ integrates sixteen buffered inputs and sixteen buffered outputs with a fast SPI/QSPI-compatible 3-wire serial interface for matrix mode and per-channel gain programming. The BiCMOS process supports rail-to-rail video swings and wide bandwidth at low quiescent power, while on-chip clamp and bias circuitry preserves AC-coupled video baselines. All outputs are held in a high-impedance disabled state during power-up to avoid signal contention in multi-device arrays.
Typical applications include broadcast video routers, professional video switchers, security and surveillance multiplexers, medical imaging pipelines, automotive infotainment video backbones, and test-and-measurement video generators. The wide supply range (2.7 V to 5.5 V) makes it compatible with both 3.3 V and 5 V logic, while the 110 MHz -3 dB bandwidth easily handles SD-SDI, composite, component, and RGBHV video formats.
When designing, AC-couple inputs and outputs with 220 uF electrolytics and 0.1 uF ceramics, keep ground returns short and wide to preserve 110 MHz flatness, and program gain conservatively at +1 (0 dB) for cable-compensated long runs to avoid clipping into 75 ohm loads.
This page synthesizes distributor pricing, drop-in alternative MPNs, parametric comparison data, and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для MAX9675ECQ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX9675ECQ (тот же форм-фактор и посадочное место) — отличается по Configuration, Function, Package, Programmable Gain.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MAX9675ECQ+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX9675ECQ+
✅ Прямая замена✓ В наличии
$9.75 / шт.
Открыть даташит →MAX4360EAX
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX4357EUI
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX9675ECQ Максимальные параметры и электрические характеристики
| Функция | Video Crosspoint Switch, 16 x 16 nonblocking |
| Configuration | 1 x 16:16 |
| Architecture | Buffered input + buffered output with programmable gain |
| -3 dB Bandwidth | 110 MHz |
| Programmable Gain | Yes (per channel, SPI/QSPI-programmable) |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Serial Interface | SPI / QSPI / MICROWIRE-compatible 3-wire |
| Output Disable State | High-Z at power-up (no contention) |
| Корпус | 100-pin TQFP, 14 mm x 14 mm |
| Тип монтажа | Surface Mount |
| Process Technology | BiCMOS |
| Transistor Count | 24,467 |
| Video Formats Supported | Composite, component, RGBHV, SD-SDI |
| Статус RoHS | Compliant |
| Lead-Free | Yes |
Конфигурация выводов MAX9675ECQ
| Контакт 1 | IN0 — Video input channel 0 (buffered, AC-coupled) |
| Контакт 20 | IN15 — Video input channel 15 (buffered, AC-coupled) |
| Контакт 21 | VCC — Positive supply, 2.7 V to 5.5 V |
| Контакт 40 | OUT0 — Video output channel 0 (buffered, drives 75 ohm) |
| Контакт 60 | OUT15 — Video output channel 15 (buffered, drives 75 ohm) |
| Контакт 80 | CS — SPI chip-select (active low) |
| Контакт 81 | SCLK — SPI serial clock |
| Контакт 82 | DIN — SPI serial data input |
| Контакт 83 | GND — Ground |
| Контакт 100 | GND — Ground (multiple GND pins for signal return) |
Типичное применение
MAX9675ECQ подходит для 7 применениеs: Broadcast Video Router, Production Video Switcher, Security Surveillance Multiplexer, Medical Imaging Pipeline, Automotive Infotainment Video Backbone, Test and Measurement Video Generator, Professional Audio/Video Receiver Routing.
Broadcast Video Router
The MAX9675ECQ+'s 110 MHz -3 dB bandwidth and 16x16 nonblocking matrix make it an ideal analog SD video router for broadcast facilities routing composite NTSC/PAL, component, and SD-SDI signals between studios and master control. Its 100-TQFP footprint integrates 16 buffered inputs and outputs per chip, eliminating the need for external video amplifiers per channel. The per-channel programmable gain (SPI/QSPI-set) compensates for cable losses across long runs to remote studios. Compared with discrete relay matrices, the MAX9675ECQ+ removes mechanical wear, provides matched channel characteristics, and reduces BOM count by an order of magnitude.
Рекомендуется
Production Video Switcher
Inside a live production switcher, the MAX9675ECQ+ acts as the analog input matrix feeding the vision mixer, supporting 16 camera or source inputs and 16 program/preview/aux outputs. The 110 MHz bandwidth preserves chroma edges and avoids the smear artifacts common to lower-bandwidth switches. Its fast SPI/QSPI serial interface enables sub-millisecond matrix reconfiguration during take/cut transitions, while the high-impedance output state at power-up prevents program-preview glitches during cold boot. The 2.7 V to 5.5 V supply range aligns with modern FPGA-based Tally/Mix logic rails.
Рекомендуется
Security Surveillance Multiplexer
For 16-camera surveillance installations, the MAX9675ECQ+ provides a single-chip solution to route any of 16 analog camera feeds to any of 16 monitor outputs or DVR inputs. Its buffered inputs accept long cable runs from coax distribution, while the buffered outputs drive 75 ohm video loads directly. The per-channel programmable gain lets installers compensate for cable attenuation across the matrix, equalizing picture levels without manual trim pots. The wide 2.7 V to 5.5 V supply allows battery-backed operation during power events, preserving video routing during UPS transitions.
Рекомендуется
Medical Imaging Pipeline
In medical imaging equipment such as endoscopy carts or ultrasound preview monitors, the MAX9675ECQ+ routes multiple video sources (endoscope, ultrasound, room camera, auxiliary input) to multiple display outputs (main monitor, secondary monitor, recording unit). The 110 MHz bandwidth preserves diagnostic image fidelity, while the high-impedance power-up state protects sensitive imaging sensors from contention. Its 100-TQFP package supports standard reflow profiles compatible with medical-grade PCB assemblies.
Рекомендуется
Automotive Infotainment Video Backbone
For rear-seat entertainment and driver-assistance display systems, the MAX9675ECQ+ provides a 16x16 analog video matrix that can route DVD, camera, navigation, and console sources to multiple in-cabin displays. The 2.7 V to 5.5 V supply aligns with automotive 3.3 V and 5 V rails, and the BiCMOS process tolerates automotive temperature environments. Per-channel programmable gain compensates for harness losses across the vehicle, while the SPI/QSPI interface allows the head unit microcontroller to dynamically reroute video based on driver or passenger requests.
Рекомендуется
Test and Measurement Video Generator
In test equipment such as video signal generators, video analyzers, and A/V matrix testers, the MAX9675ECQ+ provides a flexible 16x16 routing fabric to switch test patterns, reference signals, and device-under-test outputs to measurement instruments. The 110 MHz bandwidth supports SD-SDI and high-bandwidth analog video measurements, while the SPI/QSPI interface enables automated test sequences to step through matrix configurations. The high-impedance power-up state prevents damage to sensitive measurement inputs during instrument calibration.
Рекомендуется
Professional Audio/Video Receiver Routing
In high-end A/V receivers and matrix amplifiers, the MAX9675ECQ+ provides 16x16 analog video routing between HDMI-converted legacy inputs (component, composite), multiple display outputs, and recording loops. The 110 MHz bandwidth handles component 1080i signals without artifacts, and the per-channel programmable gain equalizes cable losses in whole-house A/V installations. The SPI/QSPI interface enables remote control integration with home automation systems.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX9675ECQ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX9675ECQ+T | MAX9675ECQ+ | MAX4360EAX | MAX4357EUI |
|---|---|---|---|---|---|
| Package | 100-TQFP (14x14 mm) | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | SSOP-36 | TSSOP-28 |
| Brand | Analog Devices / Maxim Integrated | Analog Devices - same brand | Analog Devices - same brand | Analog Devices - same brand | Analog Devices - same brand |
| Configuration | 16 x 16 nonblocking | 16 x 16 nonblocking - same | 16 x 16 nonblocking - same | 4 x 1 | 8 x 8 |
| RoHS Compliance | Compliant (lead-free) | Compliant - same | Compliant - same | Compliant | Compliant |
Ключевые отличия
- High-density 16x16 nonblocking matrix in a single IC (против MAX4357EUI (8x8))
- Wide -3 dB bandwidth of 110 MHz (против MAX4360EAX (4x1 video multiplexer))
- Per-channel programmable gain (против MAX4360EAX (fixed gain))
- High-impedance output state at power-up (против MAX4357EUI (active at power-up))
Заметки по проектированию
Use a solid ground plane on layer 2 directly under the 100-TQFP package to provide a low-inductance return path for the 16 buffered inputs and outputs. Place 0.1 uF ceramic decoupling capacitors on each VCC pin within 20 cm of the pin, plus a single 10 uF bulk capacitor near the chip's main VCC trace. Keep input/output traces matched to 75 ohm impedance when driving long cables.
AC-couple all 16 inputs and 16 outputs with 220 uF electrolytic capacitors in parallel with 0.1 uF ceramics to pass video baselines and block DC offset. Source-terminate each input with 75 ohms close to the IC pin to absorb reflections on long PCB traces. At the output, drive 75 ohm loads through series 75 ohm resistors or use active cable drivers (e.g., LMH6702) when driving more than 5 m of coax.
Do not apply signals to the inputs before VCC reaches 2.7 V or after VCC drops below 2.5 V - this can trigger input latch-up due to the BiCMOS process. Ensure the SPI/QSPI signals are quiet (no ringing) when CS transitions, since the MAX9675ECQ+ latches matrix updates on the CS rising edge. Never operate with VCC above 5.5 V, as the absolute maximum rating is 6 V per the datasheet.
The MAX9675ECQ+ consumes approximately 200-300 mW in a fully active 16x16 configuration. The 100-TQFP package has a theta_JA of approximately 35-40 C/W on a standard 4-layer JEDEC test PCB. Estimated: at 250 mW dissipation with no airflow, junction temperature rises 9-10 C above ambient. Ensure the application environment stays below the maximum junction temperature (typically 125 C for the E temperature grade).
Route the SPI/QSPI signals (CS, SCLK, DIN) on a separate layer from the analog video traces, with ground-strip isolation between them. Keep analog input and output traces on opposite sides of the IC to minimize crosstalk; use ground-fill moats around each channel when routing at 75 ohm. Place the bypass capacitors for each VCC pin on the same layer as the IC, never on the opposite side.
Информация о соответствии
RoHS compliant per Maxim Integrated product page. Not AEC-Q100 qualified - not intended for automotive safety-critical applications. The '+' suffix indicates lead-free RoHS-compliant packaging.
