MB91F467DBPVSR-GSE2 - 32-Bit FR60 RISC MCU 96MHz | Infineon
Артикул: MB91F467DBPVSR-GSE2 ✓ АктивенMB91F467DBPVSR-GSE2 Обзор
A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (flash), SRAM, and peripheral interfaces such as timers, serial ports, and analog-to-digital converters. Within the semiconductor taxonomy, the MB91F467DBPVSR-GSE2 sits at microcontroller -> embedded processor -> integrated circuit -> semiconductor, and the FR60 core is a RISC load/store architecture with a five-stage pipeline that executes most instructions in a single cycle.
Key features include 1.0625 MB (1.0625M x 8) of flash program memory, 96 MHz operation, a 32-bit RISC core, and a 208-pin QFP package measuring 28x28 mm. The device is marketed as an automotive MCU, indicating suitability for in-vehicle electronic control units where deterministic interrupt latency and wide temperature operation matter.
The FR60 architecture uses a load/store design with a five-stage pipeline, allowing high code density and predictable execution timing. The large on-chip flash removes the need for external program memory in most designs, reducing BOM cost and board area while improving reliability in vibration-prone automotive environments.
Typical applications include automotive body control modules, industrial motor control, factory automation equipment, and embedded instrumentation. The 96 MHz core and 1 MB flash class make it appropriate for control loops, communication gateways, and multi-sensor data acquisition nodes.
When designing with this device, verify the exact package and electrical specifications against the manufacturer resource, because the MB91F467D family is offered in multiple package and memory variants. Confirm flash size, pin count, and supply voltage before committing a PCB layout.
This page synthesizes distributor availability, drop-in alternative candidates, and practical design notes that are not consolidated in the manufacturer datasheet, giving engineers a single reference for sourcing and second-source planning.
Аналоги без доработки для MB91F467DBPVSR-GSE2 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
MB91F467DBPVSR-GS-N2K5E2
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MB91F467DBPFVS-GSE2
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MB91F467DAPVSR-GSE2
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MB91F467DBPVS-GSE2
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MB91F465DAPFVS-GSE2
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MB91F467DBPVSR-GSE2 Максимальные параметры и электрические характеристики
| Core Architecture | 32-bit FR60 RISC, load/store, five-stage pipeline |
| Maximum Operating Frequency | 96 MHz |
| Program Memory Size | 1.0625 MB (1.0625M x 8) FLASH |
| Program Memory Type | FLASH |
| Разрядность шины данных | 32-bit |
| Корпус / Типоразмер | 208-pin PQFP (28x28 mm) |
| Тип монтажа | Surface Mount |
| Product Series | MB91460D |
| Device Class | Automotive MCU |
| Packaging | Tray / Tape & Reel (variant dependent) |
Руководство по цоколевке MB91F467DBPVSR-GSE2 в корпусе 208-pin pqfp (28x28 mm)
Цоколевка для MB91F467DBPVSR-GSE2 (корпус 208-pin pqfp (28x28 mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для MB91F467DBPVSR-GSE2.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MB91F467DBPVSR-GSE2 подходит для 6 применениеs: Automotive Body Control Module, Industrial Motor Control, Factory Automation Controller, Embedded Instrumentation, Automotive Gateway and Telematics, Multi-Axis Motion Controller.
Automotive Body Control Module
The MB91F467DBPVSR-GSE2 fits automotive body control modules because its 96 MHz FR60 RISC core and 1.0625 MB of on-chip flash can host the large control and communication firmware stacks these units require, while the 208-pin QFP provides enough I/O for door, lighting, and window actuator drivers. Distributor listings classify the part as an automotive MCU, and the MB91460D family is positioned for in-vehicle embedded control. In a typical BCM, the MCU runs a real-time scheduler that polls switch inputs, drives relay or MOSFET outputs, and exchanges CAN or LIN frames with the vehicle network. The trade-off is board area: a 28x28 mm 208-pin QFP demands a large land pattern, so it suits centralized body controllers rather than small distributed nodes.
Рекомендуется
Industrial Motor Control
The MB91F467DBPVSR-GSE2 suits industrial motor control because a 96 MHz 32-bit FR60 core with a five-stage pipeline delivers the deterministic, single-cycle execution needed for field-oriented control loops, while 1.0625 MB of flash stores motor parameter tables and communication stacks. The 208-pin QFP supplies the I/O count required for multi-channel PWM, encoder feedback, and fault inputs on a three-phase inverter. In a typical drive, the MCU executes a current-control ISR at 10-20 kHz, updates PWM duty registers, and monitors overcurrent comparators. The trade-off versus a dedicated motor-control MCU is the absence of integrated high-voltage gate drivers, so external gate-drive circuitry is still required.
Рекомендуется
Factory Automation Controller
The MB91F467DBPVSR-GSE2 is well matched to factory automation controllers because its 96 MHz FR60 core and 1.0625 MB flash support PLC-style ladder execution, motion interpolation, and industrial protocol stacks on a single chip. The 208-pin QFP provides the I/O density needed for digital input modules, relay outputs, and encoder interfaces in a compact controller. In this role the MCU scans inputs, executes the control program, and refreshes outputs within a deterministic cycle time, while a serial or Ethernet link reports status to a supervisory system. The trade-off is that the device has no integrated Ethernet MAC in the verified data, so network connectivity requires an external controller.
Рекомендуется
Embedded Instrumentation
The MB91F467DBPVSR-GSE2 fits embedded instrumentation because the 96 MHz 32-bit core and 1.0625 MB flash allow signal-processing routines, calibration tables, and display firmware to coexist in one device. The 208-pin QFP offers enough pins for parallel display buses, keypad matrices, and multiple sensor front ends. In a typical instrument, the MCU samples an external ADC or its on-chip converter, applies scaling and filtering, and updates a display at a fixed refresh rate. The trade-off versus a dedicated DSP is lower arithmetic throughput per clock, so heavy FFT or filter workloads may need an external accelerator or a higher-clock device.
Рекомендуется
Automotive Gateway and Telematics
The MB91F467DBPVSR-GSE2 can serve as an automotive gateway or telematics controller because its 96 MHz FR60 core and 1.0625 MB flash can buffer and route CAN, LIN, and serial frames between vehicle network segments. The 208-pin QFP provides the multiple serial channels and I/O needed to interface several buses simultaneously. In a gateway, the MCU receives frames on one bus, applies filtering and translation rules, and retransmits on another, while logging diagnostic events to flash. The trade-off is that high-throughput Ethernet backbone routing is beyond this class of device, so it is best suited to body and powertrain sub-networks rather than central Ethernet gateways.
Рекомендуется
Multi-Axis Motion Controller
The MB91F467DBPVSR-GSE2 suits multi-axis motion controllers because the 96 MHz FR60 core executes interpolation and trajectory-planning math while the 208-pin QFP supplies enough PWM and encoder channels for several axes. The 1.0625 MB flash stores motion profiles and machine parameters without external memory. In a typical controller, the MCU computes position commands for each axis, updates PWM comparators, and reads quadrature encoders in a synchronized control loop. The trade-off is that the FR60 core is a general-purpose RISC engine rather than a floating-point DSP, so complex kinematics may require fixed-point optimization or an external motion co-processor.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MB91F467DBPVSR-GSE2 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MB91F467DBPVSR-GS-N2K5E2 | MB91F467DBPFVS-GSE2 | MB91F467DAPVSR-GSE2 | MB91F465DAPFVS-GSE2 |
|---|---|---|---|---|---|
| Package | 208-QFP (28x28) | 208-QFP (28x28) - same | 208-QFP (28x28) - same | 208-QFP (28x28) - same | 208-HQFP - same footprint family |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Core Architecture | 32-bit FR60 RISC, five-stage pipeline | 32-bit FR60 RISC | 32-bit FR60 RISC | 32-bit FR60 RISC | 32-bit FR60 RISC |
| Product Series | MB91460D | MB91460D | MB91460D | MB91F467D | MB91F465D |
| Mounting Type | Surface Mount | Surface Mount | Surface Mount | Surface Mount | Surface Mount |
| Distributor Availability | Octopart (2 distributors), Kynix, JaronSemi, emin.asia | DigiKey (listed) | JaronSemi (listed) | Mouser (listed) | Utmel (comparison listing) |
Ключевые отличия
- Same-family drop-in with identical core, clock, and flash (против MB91F467DBPVSR-GS-N2K5E2)
- Larger flash than the lower-tier family member (против MB91F465DAPFVS-GSE2)
- Higher pin count than smaller-package MCUs (против MB91F467DAPVSR-GSE2)
Заметки по проектированию
The 208-pin PQFP (28x28 mm) requires a fine-pitch land pattern; use the manufacturer-recommended footprint from the datasheet rather than a generic QFP template. Keep the 0.5 mm-class lead pitch in mind when selecting solder paste stencil thickness and reflow profile. Provide adequate copper area under the device for heat spreading, since a 96 MHz 32-bit MCU in a 208-pin QFP can dissipate meaningful power at full clock. Verify the exact package drawing against the manufacturer resource before releasing the PCB.
The verified data does not state the supply voltage range for the MB91F467DBPVSR-GSE2, so confirm the core and I/O rail voltages from the manufacturer datasheet before designing the power tree. As a general practice for 32-bit MCUs of this class, decouple every VCC pin with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus one bulk 10 uF capacitor per rail. Estimated: if the device draws on the order of 100 mA at 96 MHz, a 10 uF bulk capacitor provides adequate transient support for typical load steps.
The MB91F467D family is offered in multiple package and memory variants, and distributor listings show several closely related ordering codes (MB91F467DBPVSR-GS-N2K5E2, MB91F467DBPFVS-GSE2, MB91F467DAPVSR-GSE2). Do not assume these are interchangeable: flash size, peripheral configuration, and qualification status can differ. Always confirm the exact ordering code, flash size, and package against the manufacturer datasheet before committing a BOM or a PCB layout.
Route the external crystal or clock input as a short, guarded trace away from switching nodes, and place the load capacitors symmetrically on either side of the crystal. For a 96 MHz core, keep high-speed buses short and reference them to a continuous ground plane to control EMI. If the design uses external memory or a parallel display bus, match trace lengths within the bus group to preserve setup and hold margins at the maximum clock rate.
Информация о соответствии
The verified web data does not state RoHS, REACH, AEC-Q100, lead-free, or halogen-free status for the MB91F467DBPVSR-GSE2. Distributor listings classify it as an automotive MCU, but explicit AEC-Q100 qualification is not confirmed. Confirm all compliance attributes with Infineon before use in regulated or automotive designs.
