MC3403NG4 - 30V 1MHz Quad Op Amp | Texas Instruments
Артикул: MC3403NG4 ✓ АктивенMC3403NG4 Обзор
An operational amplifier is an active semiconductor device that uses high-gain differential amplification with negative feedback. Within the broader semiconductor hierarchy, an operational amplifier belongs to the analog amplifier and signal-conditioning category. Its inverting and non-inverting inputs determine how an external feedback network sets the closed-loop gain, while output-current capability and slew rate determine how quickly the amplifier can charge or discharge the load connected at the output.
The MC3403 provides four amplifier sections, reducing the package count and board area required for multi-channel analog systems. Its 30 V maximum supply rating provides useful headroom for industrial control equipment, while the 1 MHz gain-bandwidth product supports moderate-frequency feedback networks. The specified -25°C to 85°C operating range covers many commercial and industrial environments where a wider-temperature grade is not required.
Each amplifier section provides differential inputs and an output, allowing the device to implement inverting, non-inverting, summing, differential, and feedback-control circuits. Because all four sections share one package, the power rails and bypass network also serve the complete device. PCB designers should preserve symmetry between paired input and feedback components and route sensitive input traces away from output and supply-current paths to reduce parasitic pickup.
Typical uses include industrial process-control loops, multichannel sensor amplification, low-frequency audio preamplification, instrumentation signal conditioning, and active filtering. The quad organization is particularly useful when four related channels must operate under a common supply. For applications requiring higher precision, lower offset, faster settling, lower noise, or rail-to-rail output operation, a newer precision amplifier family should be evaluated before committing the MC3403NG4 to the design.
The most important design tradeoff is generality versus precision. The MC3403NG4 provides four inexpensive, widely applicable amplifier sections, but its 1 MHz bandwidth and legacy general-purpose architecture are not ideal for demanding sensor-front-end accuracy or high-speed signal chains. Verify input common-mode range, output swing, output-current capability, offset voltage, noise, slew rate, and stability requirements against the manufacturer datasheet for the operating conditions.
This product record combines the manufacturer’s device description with application-oriented guidance for package layout, bypassing, input routing, selection tradeoffs, and drop-in evaluation. It is structured to help engineers confirm whether a legacy quad amplifier still satisfies the electrical and environmental requirements of a new instrumentation, industrial-control, audio, or data-acquisition design.
Аналоги без доработки для MC3403NG4 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC3403NG4 (тот же форм-фактор и посадочное место) — отличается по Number of Amplifiers, Amplifier Type, Maximum Supply Voltage, Output Stage, Package.
MC3403N
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MC3403P
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →MC3403NG4 Максимальные параметры и электрические характеристики
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Supply Voltage Maximum | 30 V |
| Gain-Bandwidth Product | 1 MHz |
| Диапазон рабочих температур | -25°C to 85°C |
| Package Type | 14-pin PDP |
| Способ монтажа | Through-hole |
Конфигурация выводов MC3403NG4
| Контакт 1 | OUT1 — Amplifier 1 output |
| Контакт 2 | IN1- — Amplifier 1 inverting input |
| Контакт 3 | IN1+ — Amplifier 1 non-inverting input |
| Контакт 4 | V- — Negative supply connection |
| Контакт 5 | IN2+ — Amplifier 2 non-inverting input |
| Контакт 6 | IN2- — Amplifier 2 inverting input |
| Контакт 7 | OUT2 — Amplifier 2 output |
| Контакт 8 | OUT3 — Amplifier 3 output |
| Контакт 9 | IN3- — Amplifier 3 inverting input |
| Контакт 10 | IN3+ — Amplifier 3 non-inverting input |
| Контакт 11 | V+ — Positive supply connection |
| Контакт 12 | IN4+ — Amplifier 4 non-inverting input |
| Контакт 13 | IN4- — Amplifier 4 inverting input |
| Контакт 14 | OUT4 — Amplifier 4 output |
Типичное применение
MC3403NG4 подходит для 6 применениеs: Industrial Process-Control Loops, Multichannel Sensor Signal Conditioning, Low-Frequency Audio Preamplification, Data-Acquisition Analog Front Ends, Active Audio and Communication Filters, Instrumentation and Precision Control Support.
Industrial Process-Control Loops
The MC3403NG4 fits industrial process-control designs that require several general-purpose amplifier channels on a common supply. Its four 1 MHz amplifier sections can support sensor conditioning, error amplification, active filtering, and actuator feedback without placing four separate packages on the board. The 30 V maximum supply rating is useful for systems that include higher-voltage signal stages, while the -25°C to 85°C operating range covers many industrial environments. Designers should confirm the actual input common-mode range, output swing, and load-current capability for the selected supply. Feedback resistors should be placed close to their associated pins, and sensitive sensor inputs should be routed away from switching power nodes to avoid coupling process-control errors into the loop.
Рекомендуется
Multichannel Sensor Signal Conditioning
MC3403NG4 is useful when four sensor channels require amplification or active filtering under a shared 30 V-class supply environment. Each independent amplifier section can implement a non-inverting or inverting conditioning stage, allowing designers to standardize resistor networks and maintain similar bandwidth across channels. The 1 MHz gain-bandwidth product supports moderate-frequency instrumentation signals but not precision sensor fronts with demanding offset, drift, or noise specifications. Before deployment, verify the common-mode range around the sensor output and the output swing at the intended operating voltage. Place each input network close to the corresponding package pin, use short ground returns, and decouple the shared supply to prevent one channel’s transient activity from disturbing the other three.
Рекомендуется
Low-Frequency Audio Preamplification
The MC3403NG4 can serve as a general-purpose preamplifier in multichannel low-frequency audio equipment. Four amplifier sections provide independent signal paths for stereo or multi-zone systems, while the 1 MHz gain-bandwidth product is substantially above the audio band and allows conventional feedback networks to set the required gain. Performance at very low signal levels depends on input offset and noise, so gain-sensitive channels should be checked against the manufacturer’s electrical characteristics. Power-supply ripple can appear directly as modulation or hiss if bypassing is inadequate. Use a low-inductance ground plane, keep input and feedback nodes compact, and verify output swing before the signal reaches downstream audio stages or line-output circuitry.
Рекомендуется
Data-Acquisition Analog Front Ends
MC3403NG4 is applicable to low-frequency data-acquisition systems needing several analog channels for amplification, summing, and active filtering. The four-section package simplifies synchronization of supply and ground distribution across a multi-channel analog board. Its 1 MHz bandwidth is suitable for many low-bandwidth sensor or instrumentation signals, but offset voltage, input bias current, and noise must remain acceptable to the measurement uncertainty budget. Establish a defined analog ground strategy, bypass the supply at the device, and route inputs away from digital clocks and switching-regulator components. For precision measurements, compare the legacy amplifier’s error terms with a modern precision device before final calibration requirements and production test limits are established.
Рекомендуется
Active Audio and Communication Filters
The MC3403NG4 can implement active filters and low-frequency communication-channel conditioning stages because it provides four independent amplifiers with a 1 MHz gain-bandwidth product. Multiple sections allow cascaded stages, buffered summing networks, or gain and filtering functions to be consolidated into one package. Stability and usable bandwidth depend on the selected closed-loop gain, noise gain, load, and component tolerances, so the complete filter should be evaluated rather than relying only on the 1 MHz figure. Keep each filter stage physically separated from high-current outputs, use short feedback paths, and connect bypass capacitors directly to the supply and ground pins. The 30 V supply ceiling offers compatibility with higher-voltage analog rails when the selected operating point remains within all device limits.
Рекомендуется
Instrumentation and Precision Control Support
MC3403NG4 can support instrumentation and precision-control subsystems when the required precision is consistent with a general-purpose 1 MHz amplifier. A practical allocation might use one section for a transducer interface, one for gain shaping, one for an active filter, and one for feedback compensation. This arrangement reduces component count, but the design must preserve signal headroom at the inputs and outputs. Because accuracy can be limited by offset, bias current, output loading, and resistor tolerances, calculate the complete error budget before using the amplifier near a precision measurement boundary. The 14-pin through-hole package also simplifies manual assembly and prototype rework, making the device practical for educational, legacy-control, and low-to-moderate-volume instrumentation platforms.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC3403NG4 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC3403N | MC3403P |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin PDP | 14-pin PDP | 14-pin PDP |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits |
| Product Class | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Mounting Style | Through-hole | Through-hole | Through-hole |
Ключевые отличия
- Four general-purpose amplifiers in one through-hole package (против MC3403N)
- 30 V maximum supply capability (против MC3403P)
- Legacy general-purpose functionality suited to multichannel analog designs (против MC3403N)
Заметки по проектированию
Route each inverting and non-inverting input directly to its package pin, with feedback components placed close to the amplifier section that uses them. Keep the pin-11 positive supply and pin-4 negative supply connections short, and place the supply-bypass capacitor directly across the package pins. Separating the four amplifier sections physically within the layout is unnecessary when their signal paths are independent, but sensitive inputs should remain separated from outputs and high-current supply paths.
Do not treat the 30 V maximum supply rating as permission to operate at 30 V without checking the complete electrical characteristic table. Confirm the minimum supply, input common-mode range, output swing, output-current capability, and temperature limits for the actual operating point. Also verify that the selected closed-loop gain does not compromise stability with the intended load, because the 1 MHz gain-bandwidth product alone does not guarantee stable operation at every gain.
Use a continuous ground reference beneath the 14-pin package and avoid splitting analog and power-return paths under the device. High-value input nodes should have small enclosed areas, and output routing should not run parallel with sensitive input traces. For long cables or high-impedance sensors, add guarding or shielding near the connector and keep the amplifier input connection short. These steps reduce parasitic pickup that can otherwise appear as measurement noise or control-loop instability.
Информация о соответствии
The manufacturer product page and datasheet were used for device identity and stated operating specifications. Explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation or declaration.