MCF5480CVR166 - ColdFire V4E 166MHz MCU, 388-PBGA | NXP
Артикул: MCF5480CVR166 ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $68.37 | $68,37 |
| 10 | $62.5 | $625,00 |
| 100 | $55.4 | $5.540,00 |
| 500 | $49.1 | $24.550,00 |
| 1.000 | $46.81 | $46.810,00 |
MCF5480CVR166 Обзор
A microprocessor (MPU) is a CPU-centric integrated circuit that typically lacks on-chip flash and boots from external ROM/RAM. ColdFire V4E is a limited-superscalar, Harvard-architecture variant of the ColdFire family optimized for high code density in C and a balance of integer performance with embedded peripheral integration. The MCF548x sits in the high-performance tier of the ColdFire roadmap, with on-chip peripherals aimed at industrial control, networking, and secure connected devices. Within the broader taxonomy, ColdFire V4E derives from the original m68k architecture, occupying a niche between classic microcontrollers and high-end application processors.
The MCF5480CVR166 features hardware encryption acceleration for secure communications, dual 10/100 Ethernet MACs, dual CAN 2.0B controllers, a 32-bit PCI 2.2 bus interface, USB 2.0 full-speed, I2C, SPI, UARTs, and an SDRAM/DDR memory controller. The Harvard core with separate instruction and data buses, branch prediction, and a hardware multiply-accumulate (MAC) unit delivers roughly 254 MIPS at 166 MHz, with deterministic interrupt latency suitable for real-time control loops.
Typical applications include industrial Ethernet gateways, secure networked controllers, factory automation PLCs, building-automation routers, and PCI-based embedded boards. The integrated encryption accelerator makes the part attractive for VPN gateways and IEC 62443-compliant industrial nodes that need both TCP/IP throughput and IPsec/SSL offload.
When designing with the MCF5480CVR166, follow the NXP hardware design guide for PBGA cooling: a minimum 4-layer board with a continuous ground plane beneath the BGA is recommended, and decoupling must include a bulk capacitor within 25 mm of each supply ball. The V4E core is sensitive to supply rail sequencing - assert POR cleanly before enabling clocks, and hold RESET low for at least 32 SCLK cycles after the 3.3 V supply stabilizes.
This page synthesizes distributor pricing, parametric drop-in alternatives within the MCF548x family, and practical design notes not found on the manufacturer product page. Lifecycle status reflects NXP's published NRND (Not Recommended for New Designs) designation, which is critical sourcing intelligence for new programs.
Аналоги без доработки для MCF5480CVR166 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MCF5480CVR166 (тот же форм-фактор и посадочное место) — отличается по Package, Core Processor, FPU, Encryption Accelerator, Mounting Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MCF5482CVR200
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCF5480CZP166
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MCF5484CVR200
✅ Прямая замена✓ В наличии
$19.25 / шт.
Открыть даташит →MCF5485CVR200
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →MCF5480CVR166 Максимальные параметры и электрические характеристики
| Core Architecture | ColdFire V4E (limited superscalar Harvard) |
| Разрядность шины данных | 32-bit |
| Maximum Core Frequency | 166 MHz |
| Dhrystone Performance | ~254 MIPS at 166 MHz |
| Memory Program Memory | ROMless (external memory boot) |
| MMU | Yes |
| FPU | Yes (IEEE 754 hardware) |
| Корпус | 388-ball PBGA (27x27 mm) |
| Тип монтажа | Surface Mount (BGA) |
| Напряжение питания | 2.5 V core / 3.3 V I/O |
| Ethernet | Dual 10/100 MAC |
| CAN | Dual CAN 2.0B controllers |
| PCI | PCI 2.2 (32-bit, 66 MHz capable) |
| USB | USB 2.0 full-speed |
| Encryption Accelerator | Yes (IPsec/SSL offload) |
| Operating Temperature Grade | Industrial |
| Статус RoHS | Compliant |
| Lead Free | Yes |
Руководство по цоколевке MCF5480CVR166 в корпусе 388-ball pbga (27x27 mm)
Цоколевка для MCF5480CVR166 (корпус 388-ball pbga (27x27 mm)). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для MCF5480CVR166.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MCF5480CVR166 подходит для 7 применениеs: Industrial Ethernet Gateway, Secure Networked Controller, Factory Automation PLC, Building Automation Router, PCI-based Embedded Board, Secure VPN Gateway Appliance, Point-of-Sale / Kiosk Controller.
Industrial Ethernet Gateway
The MCF5480CVR166's dual 10/100 Ethernet MACs, MMU for full TCP/IP stack offload, and hardware encryption accelerator make it ideal as the main CPU inside a DIN-rail industrial gateway. At 166 MHz the ColdFire V4E delivers roughly 254 MIPS, which is sufficient to terminate OPC UA, Modbus TCP, and IPsec tunnels concurrently. The PCI 2.2 host bus lets designers add a second Ethernet PHY card or a wireless module without external glue logic, while the USB 2.0 port supports local configuration or USB-to-serial service interfaces. The 388-PBGA package is industrial-temp qualified, allowing deployment inside unventilated control cabinets where ambient temperatures reach 70 C.
Рекомендуется
Secure Networked Controller
The MCF5480CVR166's integrated encryption accelerator handles AES, DES, 3DES, SHA-1, and MD5 in hardware, which is essential for IEC 62443-compliant industrial nodes. Free CPU cycles remain available for the application protocol stack because encryption is offloaded. The dual CAN 2.0B controllers connect directly to industrial sensor and actuator buses, and the MMU supports full Linux or MQX/RTOS deployments that need process isolation. With 166 MHz of CPU and hardware IPsec, the device can sustain several hundred VPN tunnels at line rate on a 100 Mbit/s uplink.
Рекомендуется
Factory Automation PLC
For PLC mainboards the MCF5480CVR166 brings deterministic interrupt latency plus the connectivity mix modern PLCs require: dual Ethernet for redundant ring topologies, dual CAN for sensor networks, and PCI for I/O expansion cards. The 166 MHz ColdFire V4E core has enough headroom to run ladder-logic, motion control, and HMI rendering on a single chip. The ROMless boot from external flash lets manufacturers update firmware without re-spooling the MCU, which simplifies IEC 61131-3 programming and field upgrades. The 388-PBGA footprint and 27x27 mm body suit standard 4-layer PLC backplanes.
Рекомендуется
Building Automation Router
BACnet/IP, KNX/IP, and LonWorks gateways all need a 32-bit processor with multiple Ethernet ports and IPsec for site-to-site VPN. The MCF5480CVR166 fits this brief: dual 10/100 MACs drive two physical segments, the MMU runs a full IP stack with quality-of-service, and the hardware encryption engine secures BACnet traffic between buildings. Industrial temperature grade allows deployment in basement mechanical rooms without active cooling, while the small 27x27 mm PBGA keeps the BOM within tight building-automation cost targets.
Рекомендуется
PCI-based Embedded Board
The MCF5480CVR166's PCI 2.2 host bus allows it to act as the main CPU on a CompactPCI or PMC carrier card, serving as a single-board computer for test, measurement, and industrial vision applications. The 32-bit/66 MHz PCI interface sustains high-bandwidth DMA to frame grabbers or DSP cards without taxing the CPU. Combined with USB 2.0, dual Ethernet, and DDR memory controller, the part supports a full embedded SBC reference design on a single chip. The 388-PBGA package fits standard 6U CompactPCI board dimensions with adequate thermal relief.
Рекомендуется
Secure VPN Gateway Appliance
Hardware-accelerated AES and 3DES plus a full MMU make the MCF5480CVR166 a strong choice for low-to-mid-range VPN gateway appliances targeting small business and branch-office deployments. The 166 MHz core and on-chip encryption engine sustain roughly 80 Mbit/s of IPsec throughput, sufficient for typical 100 Mbit/s uplinks. Dual Ethernet supports WAN/LAN separation, while PCI 2.2 lets OEMs add a crypto accelerator card or extra Ethernet ports. Industrial temperature grade suits telecom closet environments that are not climate-controlled.
Рекомендуется
Point-of-Sale / Kiosk Controller
Although the MCF5480CVR166 is industrial-targeted, its mix of USB 2.0, dual Ethernet, PCI expansion, and a 166 MHz 32-bit core is also a fit for advanced POS terminals and self-service kiosks. The MMU runs embedded Linux or Windows CE with full driver stacks for touchscreens, printers, and payment terminals. The hardware encryption accelerator secures EMV card transactions, and the dual Ethernet ports separate payment traffic from the store LAN. The 388-PBGA is overkill for small kiosks but ideal for larger multi-station setups that need PCI-based expansion.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MCF5480CVR166 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MCF5482CVR200 | MCF5480CZP166 | MCF5484CVR200 | MCF5485CVR200 |
|---|---|---|---|---|---|
| Package | 388-ball PBGA (27x27 mm) | 388-ball PBGA (27x27 mm) - same | 388-ball PBGA (27x27 mm) - same | 388-ball PBGA (27x27 mm) - same | 388-ball PBGA (27x27 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Frequency | 166 MHz | 200 MHz | 166 MHz | 200 MHz | 200 MHz |
| Dhrystone MIPS | ~254 MIPS | ~308 MIPS | ~254 MIPS | ~308 MIPS | ~308 MIPS |
| Encryption Accelerator | Yes | Yes | Yes | Yes (enhanced) | Yes (enhanced) |
| Ethernet MACs | Dual 10/100 | Dual 10/100 | Dual 10/100 | Dual 10/100 | Dual 10/100 |
| PCI 2.2 Interface | Yes (32-bit, 66 MHz) | Yes (32-bit, 66 MHz) | Yes (32-bit, 66 MHz) | Yes (32-bit, 66 MHz) | Yes (32-bit, 66 MHz) |
| USB 2.0 | Full-speed | Full-speed | Full-speed | Full-speed | Full-speed |
| Lifecycle Status | NRND | NRND | NRND | NRND | Active |
Ключевые отличия
- Drop-in 200 MHz speed grade in same PBGA (против MCF5482CVR200)
- Active-family successor available (против MCF5485CVR200)
- Older MAPBGA family has different footprint (против MCF5474VR266)
Заметки по проектированию
The 388-ball PBGA at 27x27 mm has a junction-to-ambient thermal resistance typically around 15-20 C/W with a properly designed 4-layer PCB. Estimated: with 1.5 W typical dissipation in industrial-Ethernet use, junction rise is ~30 C above ambient. Provide a solid ground plane beneath the BGA and thermal vias connecting to inner copper layers. For sealed enclosures, derate to 70 C ambient max to keep Tj under 100 C.
The MCF548x PBGA uses 1.27 mm ball pitch with a full-array layout. Per NXP hardware design notes, use NSMD (non-solder-mask-defined) pads with a 0.55 mm solder mask opening for reliable assembly. Place 0402 0.1 uF decoupling capacitors on every supply ball within 25 mm trace length, and add one bulk 10 uF tantalum or ceramic capacitor per supply rail. Keep all high-speed signal traces (Ethernet, PCI, USB) at 50 ohm controlled impedance and length-match the PCI bus within 1 mm.
Do not assume the part is drop-in to MCF547x in the 256-MAPBGA package - the pinout differs and PCB rework is required. Always hold RESET low for at least 32 SCLK cycles after 3.3 V is stable; insufficient reset timing causes boot failures that look like dead silicon. Verify JTAG chain integrity before first power-up by reading the device ID - a faulty JTAG connection masks other boot issues. Finally, do not enable the encryption accelerator before initializing the bus clock - this corrupts the security key register and locks the part.
Route DDR memory traces on the top layer beneath the BGA escape region with matched 50 ohm impedance and length matching within 0.5 mm for clock pairs. Keep the USB D+/D- traces 90 ohm differential, length-matched within 0.15 mm, and away from PCI clocks. The Ethernet PHY MDI traces need 100 ohm differential with no more than two vias per pair. Place the 25 MHz main oscillator within 10 mm of the XTAL pins and guard it with a ground ring to minimize EMI.
Информация о соответствии
RoHS compliant per NXP product page. Not AEC-Q100 qualified - the part is industrial-temp grade, not automotive. Lifecycle status is NRND per NXP, which means new automotive programs should not adopt this part.
