NY7501-1/MB95F012K - Wireless Charging Tx MCU Module | Newyea
Артикул: NY7501-1/MB95F012K ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
NY7501-1/MB95F012K Обзор
Background: A wireless charging transmitter is a power-electronics sub-system that energizes a transmitting coil to induce power into a receiver (Rx) coil. Wireless charging transmitter modules typically integrate (a) a half-bridge or full-bridge power stage driving an LC tank at the Qi band of 100-205 kHz, (b) a current/voltage sense path for communication demodulation and FOD, and (c) an MCU for protocol stack, PID loop, and host I/O. The MB95F012K belongs to the F2MC-8FX family of 8-bit proprietary microcontrollers from Fujitsu, designed for low-power embedded control with on-chip ADC, timers, and PWM. Newyea is a Chinese wireless-power module house that re-packages these ICs as a turn-key solution.
Key features include integrated Qi-band resonant driver, on-board F2MC-8FX MCU, built-in foreign object detection support, and serial/UART host interface. Specific electrical limits such as input voltage range, output power rating, coil drive frequency, and pin/package information are not published in the public sources reviewed.
Typical applications include Qi-compliant 5W/10W wireless charging pads, automotive in-cabin wireless chargers, and industrial contactless power modules. The pairing of a dedicated Tx analog IC with a programmable MCU allows designers to customize FOD thresholds, modulation depth, and LED/User feedback behaviors.
When designing with this module, validate the published Qi certification against the target receiver and confirm the host MCU firmware interface. Because Newyea is the re-seller and not the original silicon vendor for the embedded ICs, long-term supply should be confirmed with Newyea directly.
Аналоги без доработки для NY7501-1/MB95F012K — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
[DATA_NEEDED: Newyea same-brand Tx module with MB95F012K MCU]
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
NY7501-1/MB95F012K Максимальные параметры и электрические характеристики
| Module Type | Wireless charging transmitter (Tx) module with integrated MCU |
| Embedded MCU | MB95F012K (F2MC-8FX 8-bit family, Fujitsu/Cypress/Infineon) |
| Embedded Tx IC | NY7501-1 (Newyea wireless charging transmitter) |
| Foreign Object Detection (FOD) | Supported via on-board MCU |
| MCU Core | F2MC-8FX (8-bit proprietary) |
| Manufacturer (Module Integrator) | Newyea |
| Silicon Vendors (ICs inside) | Newyea (NY7501-1) + Fujitsu/Cypress/Infineon (MB95F012K) |
Руководство по цоколевке NY7501-1/MB95F012K в корпусе standard
Цоколевка для NY7501-1/MB95F012K (корпус standard). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для NY7501-1/MB95F012K.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
NY7501-1/MB95F012K подходит для 6 применениеs: Qi-Compliant Wireless Charging Pad (5W BPP), In-Cabin Automotive Wireless Phone Charger, Industrial Contactless Power Module, Consumer Qi Charging Stand, Medical Device Contactless Power (Non-Implantable), IoT and Smart Home Wireless Sensor Power.
Qi-Compliant Wireless Charging Pad (5W BPP)
The NY7501-1/MB95F012K is intended for Qi-compliant 5W Baseline Power Profile (BPP) wireless charging pads used on desks, nightstands, and furniture-integrated surfaces. The NY7501-1 analog front end drives the LC tank at the Qi 100-205 kHz band, while the MB95F012K MCU runs the Qi protocol stack and PID loop for power control. Foreign object detection is handled by the on-board MCU reading the current sense path. [DATA_NEEDED: confirm exact Qi version and 5W output rating].
Рекомендуется
In-Cabin Automotive Wireless Phone Charger
The NY7501-1/MB95F012K can be designed into center-console or arm-rest mounted wireless phone chargers. The MB95F012K MCU executes proprietary fast-charge protocols and the Newyea TX IC drives the coil through an H-bridge. Automotive use requires AEC-Q100 or equivalent EMC conformance, which is [DATA_NEEDED] for this part number. The MCU's 8-bit core is sufficient for protocol handling but may not support the latest Qi 1.3 secure authentication extensions.
Рекомендуется
Industrial Contactless Power Module
Industrial applications such as factory sensor powering, robotic arm tool changers, and contactless slip-ring replacements can use the NY7501-1/MB95F012K as a turn-key Tx module. The on-board MB95F012K provides GPIO and UART for host integration with PLCs and industrial controllers. The Newyea module reduces certification burden for the integrator because the analog front end is pre-tuned. [DATA_NEEDED: confirm industrial temperature range and EMC ratings].
Рекомендуется
Consumer Qi Charging Stand
Charging stands for earbuds, smart watches, and stylus pens often use small-footprint wireless charging transmitter modules. The NY7501-1/MB95F012K provides the integrated MCU + Tx IC combination needed to drive a small coil at low power. The MB95F012K's PWM timers generate the coil drive waveform, and its ADC reads the sense path for FOD and over-current protection. [DATA_NEEDED: confirm low-power operation behavior and standby current].
Рекомендуется
Medical Device Contactless Power (Non-Implantable)
Non-implantable medical devices such as portable nebulizers, infusion pumps, and patient monitoring accessories benefit from contactless power to reduce connector wear and improve sterility. The NY7501-1/MB95F012K provides a pre-integrated Tx solution. Note that medical certification (IEC 60601) is the integrator's responsibility and is not implied by the module alone. [DATA_NEEDED: confirm EMI/EMC and isolation characteristics for medical use].
Рекомендуется
IoT and Smart Home Wireless Sensor Power
IoT devices such as door/window sensors, smart locks, and environmental monitors can be powered or recharged wirelessly using a Qi-band transmitter like the NY7501-1/MB95F012K. The MB95F012K MCU's low-power modes help the Tx module enter standby when no receiver is detected. The combination of Newyea TX IC + F2MC-8FX MCU is suited to small, infrequent-charge IoT products. [DATA_NEEDED: confirm standby current consumption].
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для NY7501-1/MB95F012K — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | [DATA_NEEDED: same-brand Newyea Tx module] |
|---|---|---|
| Brand | Newyea | Newyea |
| Embedded Tx IC | NY7501-1 (Newyea) | Newyea NY-series Tx IC |
Ключевые отличия
- Pre-integrated MCU + Tx IC module reduces BOM and certification effort (против Discrete Tx design (separate Tx IC + external MCU))
- Newyea brand support and reference firmware (против Generic Tx IC + customer-selected MCU)
- F2MC-8FX 8-bit MCU core (против Modules using 32-bit ARM Cortex-M0/M4 MCUs)
Заметки по проектированию
Do not assume the NY7501-1/MB95F012K module is Qi-certified for the latest revision (e.g. Qi 1.3.x with secure authentication). The verified public data does not state the Qi version. Confirm with Newyea before designing in for Qi-logo products. Estimated: based on typical Newyea module practice, not datasheet-confirmed.
Wireless charging Tx modules dissipate power in the H-bridge and the LC tank. At 5W output the Tx side typically loses 1-2W as heat. Provide copper pour under the module and adequate airflow. Estimated: based on Qi BPP typical losses, not datasheet-confirmed for this specific MPN.
The MB95F012K MCU and NY7501-1 analog front end must be co-located carefully to avoid digital switching noise coupling into the analog sense path. Keep the LC tank away from the MCU's clock traces and place a ground island around the analog front end. The host interface (UART/I2C) should be ESD-protected if the module pins are user-accessible.
Because this part number is a Newyea-branded module (not a single packaged IC from a major silicon vendor), the datasheet, pinout, and firmware interface are typically distributed only via the Newyea product page or sales contact. Do not assume DigiKey/Mouser-style parametric data is available.
Информация о соответствии
Compliance information is not published on the distributor pages reviewed (HQonline, DigiPart). Contact Newyea directly for RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-mineral declarations.
