Texas Instruments

OPA637BM - High-Speed Precision DiFET Op Amp | Texas Instruments

Артикул: OPA637BM ✗ Снят с производства
100 uV maximum Vdss 5 pA maximum Id TO-99-8 metal can, 8 pins Package
MOQ: 1 |

OPA637BM Обзор

The Texas Instruments OPA637BM is a single-circuit, precision high-speed DiFET operational amplifier optimized for gain-of-5 or higher closed-loop operation and offered in an 8-pin TO-99 metal-can package. Its key characteristics include a maximum input offset voltage of 100 uV, maximum input voltage drift of 0.8 uV/°C, maximum input bias current of 5 pA, and low-noise performance specified at 10 kHz.

A precision operational amplifier is an analog signal-processing component that amplifies the voltage difference between its two inputs while using negative feedback to establish closed-loop gain and bandwidth. The OPA637 belongs to the broader operational-amplifier hierarchy, combining precision, high-speed signal handling, and a DiFET input stage. DiFET operation is especially useful when low input bias current is required for high-impedance sources, sensors, and photodiode interfaces.

The amplifier provides very low noise at 10 kHz, a maximum offset voltage of 100 uV, and low thermal drift of 0.8 uV/°C. These characteristics make the OPA637BM appropriate for precision current-feedback and transimpedance circuits where the signal path must preserve small input signals. Its 5 pA maximum input bias current reduces the error generated when bias current flows through a high-value source resistance.

OPA637 is designed for stable operation at gain 5 or greater, distinguishing it from unity-gain-stable members of the OPA6x7 family. This topology is useful in high-gain signal-conditioning stages, analog control loops, and current-feedback applications requiring higher closed-loop gain. The manufacturer describes the OPA6x7 family as precision FET operational amplifiers with lower noise, lower offset voltage, and higher speed than the earlier OPA111 family.

Typical applications include precision current-to-voltage conversion, low-level sensor amplification, high-impedance buffer stages, active filtering, laboratory instrumentation, and analog measurement systems. The low-noise and low-bias-current combination is particularly valuable when the source impedance is high enough that amplifier input current or offset error would otherwise dominate the useful signal.

Designers should account for the minimum stable gain of 5, confirm the complete input common-mode and output-swing limits against the intended supply voltage, and verify stability with the selected feedback network. Because the TO-99 package is intended for through-hole insertion, mechanical clearance, socket compatibility, and thermal placement should be considered before assembly.

This product page combines the OPA637BM package and device details, exact quantity-break pricing, same-footprint alternatives, application guidance, and design notes intended to make engineering selection more efficient than a simple catalog listing.

Аналоги без доработки для OPA637BM — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с OPA637BM (тот же форм-фактор и посадочное место) — отличается по Amplifier Type, Package, Slew Rate, Input Bias Current, Input Type.

Texas Instruments
Amplifier Type: Precision, High-Speed
Slew Rate: 55 V/µs
Input Bias Current: 5 pA
Сравнить с OPA637BM →
Texas Instruments
Amplifier Type: Voltage Feedback
Package: 8-SOIC
Slew Rate: 250 V/us
Сравнить с OPA637BM →
Texas Instruments
Amplifier Type: Precision High-Speed Difet Operational Amplifier
Package: 8-PDIP (DIP-8)
Slew Rate: 135 V/us
Сравнить с OPA637BM →

OPA637BP

✅ Прямая замена
Texas Instruments
📦 TO-99-8
Precision High-Speed Difet Operational Amplifier · 1 · 80 MHz · 135 V/us · +/-4.5 V to +/-18 V · 100 uV · 0.8 uV/C · 5 pA

Уточнить цену

Открыть даташит →

OPA627

✅ Прямая замена
Texas Instruments
📦 TO-99-8
55 V/µs · 100 µV · 0.8 µV/°C · 5 pA · 4.5 nV/√Hz · 9 V to 36 V (±4.5 V to ±18 V) · -25°C to 85°C

Уточнить цену

Открыть даташит →

OPA606KM

✅ Прямая замена
📦 TO-99-8
OPA606KM uses the same TO-99-8 footprint but has different noise, offset, speed, and supply-domain ratings; the combined key-parameter match is estimated at 80%.

📋 Справочный аналог (нет в каталоге)

OPA634U

✅ Прямая замена
Texas Instruments
📦 TO-99-8
Texas Instruments (Burr-Brown) · OPA634 / OPA635 (SpeedPlus series) · Voltage Feedback · 1 · 200 MHz · 250 V/us · 5.6 nV/sqrt(Hz) · +5 V (typ)

Уточнить цену

Открыть даташит →

OPA633

✅ Прямая замена
📦 TO-99-8
OPA633 shares the TO-99-8 footprint but has different precision and dynamic specifications; the combined key-parameter match is estimated at 70% and requires circuit-level validation.

📋 Справочный аналог (нет в каталоге)

OPA637BM Максимальные параметры и электрические характеристики

Product Type Precision high-speed DiFET operational amplifier, 1 circuit
Корпус TO-99-8 metal can, 8 pins
Minimum Stable Gain 5:1
Input Offset Voltage 100 uV maximum
Input Voltage Drift 0.8 uV/°C maximum
Input Bias Current 5 pA maximum
Статус RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

Руководство по цоколевке OPA637BM в корпусе to-99-8 metal can, 8 pins

Цоколевка для OPA637BM (корпус to-99-8 metal can, 8 pins). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.

Схема цоколевки корпуса to-99-8 metal can, 8 pins для OPA637BM

Нет подробных данных о распиновке для OPA637BM.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

OPA637BM подходит для 6 применениеs: Precision Photodiode Signal Conditioning, High-Impedance Sensor Amplification, Precision Current-Feedback Amplifier, Laboratory Instrumentation Front End, Active Analog Filtering, Precision Audio and Communication Buffers.

📷

Precision Photodiode Signal Conditioning

OPA637BM fits low-level photodiode front ends because its maximum input bias current of 5 pA limits the error introduced by high source resistance. A transimpedance amplifier can use gain 5 or higher, matching the device's stability requirement, while the 100 uV maximum input offset and 0.8 uV/°C maximum drift help preserve baseline accuracy. Designers should still account for photodiode capacitance, the feedback resistor, and stray capacitance when stabilizing the high-speed signal path.

🧩

High-Impedance Sensor Amplification

OPA637BM is suitable for amplifying outputs from high-impedance sensors where bias-current error could obscure the measured signal. Its 5 pA maximum input bias current is particularly useful with resistive dividers or chemical sensors, while the maximum 100 uV offset and 0.8 uV/°C drift support stable calibration. The circuit must maintain a closed-loop gain of at least 5 and keep the input within the manufacturer's common-mode range. Guarding and clean PCB leakage control remain important at very high source impedances.

⚡

Precision Current-Feedback Amplifier

OPA637BM works well in current-feedback signal chains that need high speed, low offset, and low input current. Its gain-of-5-or-higher stability suits the higher closed-loop gain commonly selected in current-feedback designs, while the precision DiFET input stage avoids loading sensitive sources. The Texas Instruments OPA637 datasheet identifies precision high-speed analog circuitry as a principal use. Feedback-resistor values and source capacitance must be selected using the manufacturer's stability guidance rather than borrowed from a unity-gain-stable amplifier.

🔧

Laboratory Instrumentation Front End

OPA637BM can serve as the precision input stage of laboratory instrumentation measuring small differential signals. Its 100 uV maximum offset, 0.8 uV/°C maximum drift, and 5 pA maximum bias current limit several major error sources at the front of the measurement chain. The amplifier can also provide bandwidth required for higher-rate instrumentation. Use shielding, guarded layouts, and calibration routines to reduce residual interference that is not specified as an intrinsic amplifier parameter.

📡

Active Analog Filtering

OPA637BM is appropriate for active filters that combine precision with useful high-speed performance. Its low offset and drift reduce DC errors, its low input bias current minimizes loading of high-impedance filter networks, and the gain-of-5 stability requirement favors higher-order amplifier sections configured above that threshold. The Texas Instruments OPA6x7 datasheet describes broad use in precision and high-speed analog circuitry. Component tolerances, noise gain, and phase margin should be checked together to preserve filter response and stability.

🌐

Precision Audio and Communication Buffers

OPA637BM can amplify small audio-band or communications signals when low bias current, low offset, and adequate speed are more important than minimum cost. The 5 pA maximum input bias current is beneficial for high-impedance source networks, while the 100 uV maximum offset helps preserve low-level signal integrity. The device should be operated with gain 5 or above and within its supply and common-mode limits. Critical audio paths also require evaluation of input-voltage noise, output drive, and load compatibility.

Сводка рекомендуемых товаров

OPA637BM Texas Instruments Используется в: Precision Photodiode Signal Conditioning, High-Impedance Sensor Amplification, Precision Current-Feedback Amplifier, Laboratory Instrumentation Front End, Active Analog Filtering, Precision Audio and Communication Buffers OPA627 Texas Instruments Используется в: Precision Photodiode Signal Conditioning, Laboratory Instrumentation Front End OPA606KM TO-99 precision amplifier alternative Используется в: High-Impedance Sensor Amplification, Precision Audio and Communication Buffers OPA634 Same-footprint high-speed amplifier alternative Используется в: Precision Current-Feedback Amplifier OPA633 TO-99 precision amplifier alternative Используется в: Active Analog Filtering
What is the OPA637BM and what is it used for?
The OPA637BM is a precision, high-speed DiFET operational amplifier intended for low-level analog signal amplification, particularly in gain-of-5-or-higher circuits. According to the Texas Instruments OPA637 datasheet, it combines very low noise, a maximum 100 uV input offset voltage, 0.8 uV/°C maximum drift, and a maximum 5 pA input bias current. The 8-pin TO-99 package makes it especially suitable for precision instrumentation, current-to-voltage conversion, high-impedance sensor interfaces, and active analog filters.
What are the key specifications of OPA637BM that engineers should know?
The principal OPA637BM specifications are a gain-of-5 minimum stable operating point, 100 uV maximum input offset voltage, 0.8 uV/°C maximum input drift, 5 pA maximum input bias current, and very low noise characterized at 10 kHz. The Texas Instruments OPA637 datasheet identifies the device as a precision high-speed DiFET amplifier in a TO-99-8 package. Gain-bandwidth, slew rate, common-mode range, supply range, and settling-time limits should be taken from the complete datasheet when sizing the feedback network.
Where can I download the OPA637BM datasheet PDF?
The official OPA637BM datasheet PDF is available from the Texas Instruments OPA637 product-document link at https://www.ti.com/lit/ds/symlink/opa637.pdf. The document covers the OPA6x7 precision FET operational-amplifier family, including OPA637 electrical characteristics, application information, pin descriptions, and typical performance curves. Use the manufacturer document for production design decisions because it is the controlling source for supply voltage, common-mode range, noise, stability, and absolute maximum ratings.
Where can I find the OPA637BM pinout?
The OPA637BM pinout is shown in the pin-configuration section of the official Texas Instruments OPA637 datasheet. The device is an 8-pin TO-99 metal-can package, and the PDF provides the numbered connections for the differential inputs, power terminals, and output. Before assigning PCB tracks, check the pin-description table and package drawing together. The public text listing used for this page does not reproduce the individual pin names, so use the manufacturer diagram as the authoritative connection reference.
Is the OPA637BM unity-gain stable?
No, the OPA637BM is stable in gain 5 and higher. According to the Texas Instruments OPA637 datasheet, the OPA627 in the same OPA6x7 family is unity-gain stable, whereas the OPA637 requires a minimum closed-loop gain of 5. This distinction is important when selecting feedback values or designing a unity-gain voltage follower. If unity-gain operation is mandatory, use the OPA627 rather than treating the OPA637 as a direct substitute.
OPA637BM vs OPA627BM — which op amp is better for a precision amplifier?
OPA637BM is the better choice when gain-of-5-or-higher operation, high speed, and low-noise performance are priorities; OPA627BM is preferable for unity-gain buffering. According to the Texas Instruments OPA6x7 datasheet, both are precision FET operational amplifiers, but the OPA637 is stable at gain 5 while the OPA627 is unity-gain stable. The choice should therefore follow the required closed-loop gain and stability configuration rather than package identity alone.
When should I choose OPA637BM over OPA627BM?
Choose OPA637BM when the signal chain requires stable operation at a closed-loop gain of 5 or greater and benefits from the family's high-speed precision characteristics. Choose OPA627BM when a unity-gain voltage follower, integrator, or similar configuration must remain stable at gain 1. The Texas Instruments OPA6x7 datasheet identifies this stability distinction explicitly. Both devices belong to the same precision high-speed DiFET family, so gain architecture is the decisive engineering criterion.
Can OPA637BM be used in high-impedance sensor and photodiode circuits?
Yes, the OPA637BM is suitable for many high-impedance sensor and photodiode interfaces because its maximum input bias current is 5 pA. Low bias current reduces the voltage error created when current flows through a high source resistance, while the 100 uV maximum offset and 0.8 uV/°C maximum drift support accurate low-level measurements. According to the Texas Instruments OPA637 datasheet, the precision DiFET architecture is suitable for precision high-speed analog circuitry.
What is the best drop-in replacement for OPA637BM?
OPA637BP is the closest listed same-footprint replacement because it is an OPA637 variant associated with the TO-99 package family and can preserve the electrical role and pin arrangement. Other TO-99 precision alternatives include OPA627, OPA606KM, OPA634, and OPA633, but each requires a stability, noise, offset, speed, or bias-current comparison before approval. According to the Texas Instruments OPA6x7 datasheet, OPA627 is unity-gain stable and OPA637 is stable at gain 5, so package match alone does not guarantee equivalent behavior.
What can replace OPA637BM without changing the TO-99 footprint?
OPA637BP is the most direct TO-99-footprint replacement listed for OPA637BM, while OPA627, OPA606KM, OPA634, and OPA633 are possible TO-99 alternatives. A valid replacement must retain the same eight-pin mechanical outline and pin functions and must also meet the circuit's gain, noise, bias-current, offset, speed, and common-mode requirements. The Texas Instruments OPA6x7 datasheet is particularly important when comparing OPA637BM with OPA627 because their minimum stable gains differ.
Is OPA637BM suitable for precision current-feedback amplifier designs?
Yes, OPA637BM is well suited to precision current-feedback amplifier designs that operate at gain 5 or higher. The combination of very low noise, 100 uV maximum input offset voltage, 5 pA maximum input bias current, and high-speed performance supports accurate feedback compensation in current-feedback signal paths. According to the Texas Instruments OPA637 datasheet, the amplifier is intended for precision high-speed analog circuitry. The exact gain-bandwidth and stability limits must still be checked against the selected feedback resistor and signal-source impedance.
What design precautions matter when using the OPA637BM in a precision circuit?
Confirm the minimum stable gain of 5, preserve the required input common-mode range, and place the feedback network so parasitic capacitance does not destabilize the amplifier. Low input bias current only remains useful when the source impedance, guarding, connector leakage, and PCB cleanliness are controlled. According to the Texas Instruments OPA637 datasheet, OPA637 differs from unity-gain-stable OPA627, so changing feedback values without checking stability can turn a valid design into an oscillating one.
Where can I request a quote and current availability for OPA637BM?
Use the Request a Quote form on this page to request current availability, minimum order quantity, and lead time for OPA637BM. Because the TO-99BM configuration is described as discontinued in lifecycle records, procurement should confirm remaining factory stock, authorized-channel inventory, and traceability requirements before release. Quote requests should specify the required quantity, tube packaging, and any date-code or inspection requirements to avoid ambiguity.
What is the price of OPA637BM?
Current OPA637BM pricing is not presented as a fixed customer-facing figure because the component is discontinued and inventory can vary by quantity and packaging. Use the Request a Quote form on this page for a current quotation. The structured quantity-break listing on this page records 81.55 USD per unit at quantities of 1 and 10, then 60.75 USD per unit at quantities of 100, 1,000, and 10,000, but procurement should confirm availability before relying on any historical tier.
How much is the lead time for OPA637BM?
The current lead time for OPA637BM must be confirmed through the Request a Quote form on this page because lifecycle status and available inventory can change after a discontinued product enters the quotation process. State the required order quantity and whether tube packaging is acceptable. For production use, also request date-code, traceability, and visual-inspection information. The manufacturer datasheet describes the device itself but is not a commitment to current material availability.

Справочные инженерные данные для OPA637BM — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose OPA637BM for precision high-speed circuits requiring a gain of 5 or higher, low input bias current, and low DC error. It is particularly appropriate for photodiode interfaces, current-to-voltage conversion, high-impedance sensor amplifiers, precision active filters, and instrumentation front ends. OPA637BP is the closest same-family choice when ordering-code or package details are the only difference. Select OPA627 when unity-gain stability is mandatory. OPA606KM, OPA634, and OPA633 may fit the same TO-99 footprint, but they should be treated as engineering-review candidates because their noise, offset, bias-current, speed, and stability characteristics can differ. For every alternative, verify supply range, common-mode range, output swing, gain-bandwidth product, noise, and required minimum gain before releasing a PCB substitution.

Сравнение с аналогами

Параметр Этот товар OPA637BP OPA627 OPA606KM OPA634 OPA633
Package TO-99-8 TO-99-8 TO-99-8 TO-99-8 TO-99-8 TO-99-8
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments

Ключевые отличия

  • Designed specifically for stable gain-of-5-or-higher operation (против OPA627)
  • Precision offset and drift ratings (против OPA606KM)
  • Low input bias current for high-impedance sources (против OPA634)

Заметки по проектированию

Do not place OPA637BM in a unity-gain voltage follower. The manufacturer identifies OPA637 as stable at gain 5 or higher, while OPA627 is the unity-gain-stable family member. Check every feedback topology, including cascaded stages and indirect feedback paths, against the minimum gain of 5. If a design must support gain 1, select OPA627 or another amplifier explicitly rated for that configuration.

For photodiode, sensor, and other high-impedance sources, minimize leakage around the input node and use guarding where practical. The 5 pA maximum input bias current can create a substantial error when multiplied by a very large source resistance. Keep connector and PCB contamination under control, maintain a clean surface around the input, and verify that the source impedance, feedback resistor, and total input capacitance still produce a stable compensated transimpedance network.

Estimate power dissipation as the product of supply voltage and average supply current, then compare the resulting junction-temperature rise with the amplifier's maximum operating temperature. The TO-99 metal can can improve heat spreading compared with a small plastic package, but its thermal performance still depends on airflow, board copper, and socket construction. Confirm the complete operating-temperature and absolute-maximum ratings in the manufacturer datasheet before production release.

Preserve the TO-99 footprint's mechanical clearance and verify lead spacing against the current board library before layout release. Because this is a legacy through-hole package, check component height, socket selection, nearby shielding, and assembly-handling requirements. Route sensitive input traces away from power converters and clocking nodes, use a stable reference plane, and place compensation and feedback components close to the amplifier pins.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

No specific RoHS, REACH, halogen-free, lead-free, or conflict-minerals status was identified for OPA637BM. The precision amplifier is not an automotive-qualified AEC-Q100 product.

Данные проверены: 2026-11-14 — данные проверены и курируются командой компонентной инженерии XAIPART

Похожие запросы

OPA637BM datasheet OPA637BM datasheet pdf OPA637BM pinout OPA637BM TO-99-8 OPA637BM op amp equivalent OPA637BM replacement OPA637BM cross reference OPA637BM vs OPA627 OPA637BM price OPA637BM stock Texas Instruments OPA637BM OPA637BM photodiode amplifier OPA637BM current feedback amplifier OPA637 gain 5 stability OPA637 5 pA input bias current

Связанные компоненты & термины

Texas Instruments OPA637BM OPA637 OPA637BP OPA627 OPA606KM OPA634 OPA633 precision operational amplifier high-speed operational amplifier DiFET operational amplifier FET-input operational amplifier low-dropout input offset voltage input voltage drift input bias current gain-bandwidth product slew rate minimum stable gain TO-99-8 TO-99 metal can through-hole package transimpedance amplifier current-feedback amplifier precision instrumentation
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ