PIC12F509T-I/MC - 8-bit MCU, 1.5KB Flash, 4MHz, 6 I/O | Microchip
Артикул: PIC12F509T-I/MC ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0.45 | $0,45 |
| 10 | $0.4 | $4,00 |
| 100 | $0.35 | $35,00 |
| 500 | $0.31 | $155,00 |
| 1.000 | $0.28 | $280,00 |
PIC12F509T-I/MC Обзор
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral I/O into one package, enabling compact, deterministic control logic. The PIC12F509 belongs to the 8-bit PIC12F family, a lineage of low-cost, high-performance, RISC-based microcontrollers from Microchip used for cost-sensitive embedded control. Within the broader taxonomy, PIC12F509 sits in this hierarchy: microcontroller -> embedded controller -> semiconductor IC. The '509 is the larger-memory sibling of the '508, both targeting applications that need more code space than a basic 8-pin MCU typically provides.
Key features include 33 single-word, single-cycle RISC instructions, an 8-bit timer/counter, a watchdog timer with on-chip RC oscillator, and an internal 4MHz RC oscillator that eliminates the need for an external crystal in many designs. It operates from 2.0V to 5.5V and includes an 8-bit ADC-less architecture optimized for simple digital I/O control. The 6 I/O pins can each source/sink up to 25 mA, enabling direct LED or transistor drive.
Architecturally, the PIC12F509 uses a Harvard-style RISC core with a 12-bit wide instruction word, achieving 2:1 typical code compression versus competitive 8-bit MCUs. It supports in-circuit serial programming (ICSP) via two pins, allowing firmware updates without removing the device from the board. The on-chip 4MHz RC oscillator provides +/-1% accuracy over voltage and temperature, sufficient for UART-less or low-speed timing applications.
Typical applications include appliance control, LED lighting drivers, simple sensor interfaces, remote controls, battery-powered toys, and general-purpose logic replacement. The wide 2.0V to 5.5V operating range also suits 3V coin-cell designs.
When designing, remember that the DFN-8 has an exposed thermal pad that MUST be soldered to the PCB ground plane for mechanical reliability and thermal dissipation. Decoupling capacitors (100 nF + 10 uF) should be placed within 3 mm of the VDD pin, and the MCLR pin must be pulled high with a 10 kohm resistor unless the reset function is intentionally disabled.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not aggregated on the manufacturer datasheet.
Аналоги без доработки для PIC12F509T-I/MC — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC12F509T-I/MC (тот же форм-фактор и посадочное место) — отличается по Internal Oscillator, Package, Timers, Watchdog Timer, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC12F509-I/MC
✅ Прямая замена✓ В наличии
$0.55 / шт.
Открыть даташит →PIC12F509T-E/MC
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC12F508T-I/MC
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC12F508-I/MC
✅ Прямая замена✓ В наличии
$0.47 / шт.
Открыть даташит →PIC12F509-E/MC
✅ Прямая замена✓ В наличии
$0.5 / шт.
Открыть даташит →PIC12F509T-I/MC Максимальные параметры и электрические характеристики
| Core | 8-bit PIC RISC |
| Program Memory | 1.5 KB (1K x 12) Flash |
| RAM | 41 bytes |
| CPU Speed | 4 MHz (DC to 4 MHz) |
| I/O Pins | 6 |
| Supply Voltage (VDD) | 2.0 V to 5.5 V |
| Рабочая температура | -40 C to +85 C (Industrial) |
| Корпус | DFN-8 (3x2 mm, 0.90 mm height) |
| Тип монтажа | Surface Mount (with exposed pad) |
| Internal Oscillator | 4 MHz RC (factory calibrated, +/-1%) |
| Timers | 1 x 8-bit Timer/Counter (TMR0) |
| Watchdog Timer | Yes (with on-chip RC oscillator) |
| ADC | None |
| Instruction Set | 33 single-word, single-cycle RISC instructions |
| Programming Interface | ICSP (In-Circuit Serial Programming) |
| Brown-out Detect | Yes |
| I/O Pin Current (source/sink) | 25 mA per pin |
| Статус RoHS | Compliant (lead-free) |
| Уровень MSL | 1 |
| Packaging Type | Tape & Reel |
Конфигурация выводов PIC12F509T-I/MC
| Контакт 1 | GP0 — General-purpose I/O bit 0 (also ICSPCLK) |
| Контакт 2 | GP1 — General-purpose I/O bit 1 (also ICSPDAT) |
| Контакт 3 | GP2 — General-purpose I/O bit 2 (T0CKI clock input) |
| Контакт 4 | GP3/MCLR/VPP — Input-only GPIO, Master Clear reset, programming voltage |
| Контакт 5 | VDD — Positive supply voltage (2.0V-5.5V) |
| Контакт 6 | VSS — Ground reference |
| Контакт 7 | GP5/OSC1 — General-purpose I/O bit 5, crystal oscillator input |
| Контакт 8 | GP4/OSC2 — General-purpose I/O bit 4, crystal oscillator output |
Типичное применение
PIC12F509T-I/MC подходит для 6 применениеs: Battery-Powered Remote Control, LED Lighting Driver / Strip Controller, Appliance Control Board Replacement, Sensor Interface / Simple Signal Conditioning, Cost-Sensitive Toy and Hobby Electronics, Industrial Logic Replacement (Timers / Counters).
Battery-Powered Remote Control
The PIC12F509T-I/MC is well suited to handheld battery-powered remote controls thanks to its 2.0V-5.5V supply range that lets it run directly from a single 3V coin cell down to end-of-life voltage. The internal 4MHz RC oscillator eliminates the crystal, the 6 GPIO pins can directly key-scan a 3x3 matrix or drive an IR LED through a transistor, and the 1.5KB Flash easily holds state-machine transmit code for NEC or RC-5 protocols. Brown-out detect protects against cell voltage sag that would otherwise corrupt the Flash. Estimated average active current is well under 1 mA at 4MHz and 3V, giving months of life from a CR2032.
Рекомендуется
LED Lighting Driver / Strip Controller
For addressable LED strip controllers, the PIC12F509T-I/MC provides 6 GPIO pins capable of 25 mA source/sink, enough to drive low-side MOSFETs for one or two LED channels directly. The 25 mA I/O capability is also sufficient to drive the WS2812/APA102 data line via bit-banging if firmware is tightly written within the 1.5KB Flash budget. The internal 4MHz RC oscillator provides adequate timing resolution for WS2812's +/-150 ns reset pulse and +/-100 ns data bit windows. With 41 bytes RAM the device can buffer 10-15 LED states, enabling modest chase/breathing patterns.
Рекомендуется
Appliance Control Board Replacement
The PIC12F509T-I/MC is commonly used to replace discrete logic in small home appliances - coffee makers, fans, humidifiers, simple thermostats. Its 2.0V-5.5V range covers both 3.3V sensor interfaces and 5V relay coils, while the 25 mA GPIO drive can pull small relays directly or interface ULN2003 for larger loads. The watchdog timer with on-chip RC prevents firmware lockup in unattended appliances, and brown-out detect prevents undefined behavior during brownouts. With 1.5KB Flash, the device can hold complete state machines for hysteresis control, button debouncing, and timing profiles.
Рекомендуется
Sensor Interface / Simple Signal Conditioning
In sensor-interface roles where the PIC12F509T-I/MC acts as a digital preprocessor, the 6 GPIO pins handle digital sensor reads, switch debouncing, and counter accumulation. While the device has no built-in ADC, an external sigma-delta modulator or I2C/SPI sensor can be bit-banged using the same GPIO. The 4MHz instruction rate allows sampling rates up to 1 MHz for simple digital protocols. The 1.5KB Flash supports basic calibration tables, smoothing filters, and threshold detection - replacing an analog comparator circuit with a deterministic digital implementation.
Рекомендуется
Cost-Sensitive Toy and Hobby Electronics
For cost-driven consumer toys and hobby kits, the PIC12F509T-I/MC delivers Microchip PIC reliability at $0.41 unit pricing in volume. The DFN-8 (3x2 mm) package keeps PCB cost minimal, while 6 GPIO pins are sufficient for motor direction/H-bridge control of small DC motors, sound trigger logic, or simple servo timing. The ICSP programming interface supports field firmware updates during development. Hobbyists can program the chip using a $20 PICkit 3 or PICkit 5 debugger, with the 33-instruction RISC set being approachable for beginners.
Рекомендуется
Industrial Logic Replacement (Timers / Counters)
In industrial 24V-tolerant logic-replacement designs (with external level shifters), the PIC12F509T-I/MC provides a programmable replacement for 555-timer-style circuits and discrete counters. The 8-bit TMR0 with internal or external clock can be configured for 1-second to 1-millisecond timing, and the watchdog timer ensures reliability in unattended equipment. Industrial-grade -40C to +85C operation handles factory-floor temperature swings, while brown-out detect and the wide 2.0V-5.5V supply range tolerate noisy 24V rail-derived supplies after regulation. The 1.5KB Flash supports multiple timing modes selectable via GPIO at runtime.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC12F509T-I/MC — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC12F509-I/MC | PIC12F509T-E/MC | PIC12F508T-I/MC | PIC12F508-I/MC | PIC12F509-E/MC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | DFN-8 (3x2 mm) | DFN-8 (3x2 mm) - same | DFN-8 (3x2 mm) - same | DFN-8 (3x2 mm) - same | DFN-8 (3x2 mm) - same | DFN-8 (3x2 mm) - same |
| Flash Program Memory | 1.5 KB (1K x 12) | 1.5 KB - same | 1.5 KB - same | 768 B (-50%) | 768 B (-50%) | 1.5 KB - same |
| RAM | 41 bytes | 41 bytes - same | 41 bytes - same | 25 bytes (-39%) | 25 bytes (-39%) | 41 bytes - same |
| CPU Clock Speed | 4 MHz | 4 MHz - same | 4 MHz - same | 4 MHz - same | 4 MHz - same | 4 MHz - same |
| I/O Pins | 6 | 6 - same | 6 - same | 6 - same | 6 - same | 6 - same |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C - same | -40C to +125C (Extended) | -40C to +85C - same | -40C to +85C - same | -40C to +125C (Extended) |
| Packaging Format | Tape & Reel (T suffix) | Tube | Tape & Reel | Tape & Reel | Tube | Tube |
Ключевые отличия
- Lowest-cost 8-pin PIC12F with 1.5KB Flash (против PIC12F508T-I/MC)
- Wide 2.0V-5.5V supply supports coin-cell designs (против PIC12F1840-E/MF)
- Internal 4MHz RC oscillator at +/-1% accuracy (против PIC12F509T-E/MC)
Заметки по проектированию
The DFN-8 package has an exposed thermal pad on its underside that MUST be soldered to a PCB copper pad for mechanical reliability and thermal dissipation. Without a proper soldered thermal pad, the package can crack under thermal stress or mechanical flex. Recommended footprint uses an array of thermal vias (0.3 mm drill, 0.5 mm pitch) under the pad connecting to the inner ground plane. Decoupling capacitors (100 nF ceramic + 10 uF bulk) should be placed within 3 mm of the VDD pin.
Pin 4 (GP3/MCLR/VPP) serves triple duty: it can be a digital input only, the device Master Clear reset, and the ICSP programming voltage input. If used as MCLR, connect it to VDD via a 10 kohm pull-up resistor and place a 100 nF capacitor from MCLR to ground for noise immunity. If the MCLR function is disabled in configuration bits, GP3 becomes a digital input only. Forgetting the MCLR pull-up is one of the most common causes of intermittent resets in production designs.
When using an external crystal (optional on PIC12F509), place the crystal and its load capacitors within 5 mm of the OSC1/OSC2 pins to minimize parasitic capacitance. Keep the crystal traces short and away from switching signals to avoid EMI coupling. For most cost-sensitive designs, prefer the internal 4MHz RC oscillator and avoid the crystal entirely - factory calibration provides +/-1% accuracy which is adequate for LED PWM, simple timing, and bit-banged protocols below 38.4 kbps.
The PIC12F509T-I/MC draws approximately 1-2 mA active at 4MHz/5V and less than 1 uA in sleep mode. For battery-powered designs, use sleep mode aggressively and wake on GPIO change interrupts or watchdog timer overflow. Brown-out detect should be enabled to prevent Flash corruption during supply voltage sag. The wide 2.0V-5.5V supply range allows direct operation from a 2xAA alkaline pack (3.0V nominal, sagging to 2.0V end-of-life) without a boost regulator.
Each GPIO can source or sink 25 mA, but the total package dissipation budget is limited. Total GPIO current across all 6 pins should not exceed 200 mA combined for reliable operation. For higher-current loads, drive a MOSFET or ULN2003 from a GPIO pin rather than connecting LEDs directly. When bit-banging protocols like WS2812, account for instruction-cycle timing - at 4MHz each instruction is 1 us, so tight 250 ns WS2812 timing windows require careful assembly optimization.
Информация о соответствии
RoHS-compliant per DigiKey listing (lead-free DFN package). Not AEC-Q100 qualified; the 'E' extended-temp variant is industrial-grade not automotive. Reach SVHC compliant per Microchip product declarations.
