PIC16C64A-20E/L - 8-Bit 20MHz OTP MCU, 3.5KB, 44-PLCC | Microchip
Артикул: PIC16C64A-20E/L ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $14.95 | $14,95 |
| 10 | $13.46 | $134,60 |
| 100 | $11.96 | $1.196,00 |
| 250 | $10.47 | $2.617,50 |
| 500 | $8.97 | $4.485,00 |
PIC16C64A-20E/L Обзор
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data memory, and peripherals on one die. Within the broader taxonomy, a microcontroller belongs to the integrated circuit (IC) family and specifically the microcontroller subcategory, sitting alongside microprocessors, DSPs, and FPGAs. The PIC16C6X architecture uses a RISC (Reduced Instruction Set Computer) instruction set with only 35 single-word instructions, where all instructions execute in one cycle except program branches (two cycles), making code generation compact and deterministic for embedded developers.
Key features include a wide operating voltage range of 2.5V to 6.0V (commercial/industrial/extended grades), low-power consumption at 5V/4 MHz of approximately 15 µA typical and 3V/32 kHz of approximately 1 µA typical, a fully static design that supports DC to 20 MHz operation, an 8-bit timer/counter with 8-bit prescaler, a watchdog timer, and analog comparator peripheral support. The /L package suffix denotes the 44-lead PLCC (Plastic Leaded Chip Carrier) form factor, a J-lead surface-mount package well suited for socketed industrial designs and through-hole-friendly repair workflows.
The PIC16C64A-20E/L uses Harvard architecture with separate program and data buses, EPROM-based program storage, and CMOS fabrication. Its -20E speed designation indicates 20 MHz maximum clock at the Extended temperature range (-40°C to +125°C), distinguishing it from the standard 0°C to +70°C commercial version. This part falls under Microchip's "Not Recommended for new designs" status with the newer PIC16C65B suggested as a successor in the same family.
Typical applications include industrial automation control loops, consumer-electronics user-interface controllers, low-power battery sensing nodes, automotive body and chassis subsystems, and legacy embedded systems that require a stable CMOS OTP supply chain. The wide temperature range and 33 I/O count make it a fit for HMI panels, motor-control front ends, and instrumentation front ends.
When designing with this device, ensure in-circuit serial programming (ICSP) header access for OTP programming, validate the minimum 4.0V Vdd for 20 MHz operation, and budget for the OTP one-time-program window during production. Consider migrating to PIC16C65B or a flash-based PIC16F equivalent for new designs to gain re-programmability and modern peripherals.
This page synthesizes distributor pricing, drop-in package alternatives, and practical engineering notes not found in the manufacturer datasheet alone.
Аналоги без доработки для PIC16C64A-20E/L — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16C64A-20E/L (тот же форм-фактор и посадочное место) — отличается по Package, Mounting Type, Core, Data EEPROM, Timers.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16C64A-20/L
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC16C64A-10/L
✅ Прямая замена✓ В наличии
$5.5 / шт.
Открыть даташит →PIC16C64A-04/L
✅ Прямая замена✓ В наличии
$6.2 / шт.
Открыть даташит →PIC16C65B-20/L
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC16C64A-04I/L
✅ Прямая замена✓ В наличии
$4.5 / шт.
Открыть даташит →PIC16C64A-10I/L
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.45 / шт.
Открыть даташит →PIC16C64A-04I/PT
✅ Прямая замена✓ В наличии
$4.61 / шт.
Открыть даташит →PIC16C64A-20E/L Максимальные параметры и электрические характеристики
| Manufacturer | Microchip Technology |
| Series | PIC 16C |
| Core Processor | PIC |
| Core Size | 8-Bit |
| Максимальная тактовая частота | 20 MHz |
| Instruction Cycle Time | 200 ns |
| Program Memory Size | 3.5 KB (2K x 14) OTP |
| RAM Size | 128 x 8 |
| Number of I/O Pins | 33 |
| Корпус / Типоразмер | 44-PLCC (16.59 x 16.59 mm) |
| Operating Supply Voltage Range | 2.5 V to 6.0 V |
| Диапазон рабочих температур | -40 °C to +125 °C (Extended, "E") |
| Supply Current (5 V / 4 MHz) | 15 µA typical |
| Supply Current (3 V / 32 kHz) | 1 µA typical |
| Program Memory Type | OTP EPROM |
| Architecture | Harvard, RISC, 35 single-word instructions |
| Тип монтажа | Surface Mount (PLCC J-lead) |
Конфигурация выводов PIC16C64A-20E/L
| Контакт 1 | MCLR — Master Clear (Reset, active low) |
| Контакт 2 | RA0 — PORTA bit 0 (bidirectional I/O) |
| Контакт 3 | RA1 — PORTA bit 1 (bidirectional I/O) |
| Контакт 4 | RA2 — PORTA bit 2 (bidirectional I/O) |
| Контакт 5 | RA3 — PORTA bit 3 (bidirectional I/O) |
| Контакт 6 | RA4 — PORTA bit 4 / T0CKI (timer0 clock input) |
| Контакт 7 | RA5 — PORTA bit 5 / analog input |
| Контакт 8 | VSS — Ground reference |
| Контакт 9 | OSC1 — Oscillator input |
| Контакт 10 | OSC2 — Oscillator output / clock out |
| Контакт 11 | RC0 — PORTC bit 0 (bidirectional I/O) |
| Контакт 12 | RC1 — PORTC bit 1 (bidirectional I/O) |
| Контакт 13 | RC2 — PORTC bit 2 (bidirectional I/O) |
| Контакт 14 | RC3 — PORTC bit 3 (bidirectional I/O) |
| Контакт 15 | RC4 — PORTC bit 4 (bidirectional I/O) |
| Контакт 16 | RC5 — PORTC bit 5 (bidirectional I/O) |
| Контакт 17 | RC6 — PORTC bit 6 (bidirectional I/O) |
| Контакт 18 | RC7 — PORTC bit 7 (bidirectional I/O) |
| Контакт 19 | VSS — Ground reference |
| Контакт 20 | VDD — Positive supply voltage |
| Контакт 21 | RB0 — PORTB bit 0 / external interrupt |
| Контакт 22 | RB1 — PORTB bit 1 (bidirectional I/O) |
| Контакт 23 | RB2 — PORTB bit 2 (bidirectional I/O) |
| Контакт 24 | RB3 — PORTB bit 3 (bidirectional I/O) |
| Контакт 25 | RB4 — PORTB bit 4 (bidirectional I/O) |
| Контакт 26 | RB5 — PORTB bit 5 (bidirectional I/O) |
| Контакт 27 | RB6 — PORTB bit 6 / programming clock |
| Контакт 28 | RB7 — PORTB bit 7 / programming data |
| Контакт 29 | NC — Not connected (per datasheet pinout, reserved) |
| Контакт 30 | RD0 — PORTD bit 0 (bidirectional I/O) |
| Контакт 31 | RD1 — PORTD bit 1 (bidirectional I/O) |
| Контакт 32 | RD2 — PORTD bit 2 (bidirectional I/O) |
| Контакт 33 | RD3 — PORTD bit 3 (bidirectional I/O) |
| Контакт 34 | RD4 — PORTD bit 4 (bidirectional I/O) |
| Контакт 35 | RD5 — PORTD bit 5 (bidirectional I/O) |
| Контакт 36 | RD6 — PORTD bit 6 (bidirectional I/O) |
| Контакт 37 | RD7 — PORTD bit 7 (bidirectional I/O) |
| Контакт 38 | VSS — Ground reference |
| Контакт 39 | VDD — Positive supply voltage |
| Контакт 40 | RE0 — PORTE bit 0 / read control |
| Контакт 41 | RE1 — PORTE bit 1 / write control |
| Контакт 42 | RE2 — PORTE bit 2 / chip select control |
| Контакт 43 | NC — Not connected (per datasheet pinout, reserved) |
| Контакт 44 | NC — Not connected (per datasheet pinout, reserved) |
Типичное применение
PIC16C64A-20E/L подходит для 6 применениеs: Industrial Automation Control, Consumer Electronics User Interface, Automotive Body and Chassis Subsystems, Battery-Powered Sensing Nodes, Legacy Embedded System Refresh, Instrumentation Front-End Controller.
Industrial Automation Control
The PIC16C64A-20E/L fits industrial PLC and sensor-interface boards thanks to its 33 digital I/O across five ports and 20 MHz instruction throughput. Its Extended -40 °C to +125 °C rating matches factory-automation thermal envelopes, while 128 bytes of RAM and 3.5 KB OTP suffice for ladder-logic replacement and discrete I/O scanning. The wide 2.5 V to 6.0 V supply range tolerates 24 V-derived industrial rails after regulation. Compared with switching to a flash MCU, the OTP EPROM supply chain keeps BOM stable for long production runs.
Рекомендуется
Consumer Electronics User Interface
The PIC16C64A-20E/L is well-suited for low-cost consumer UI panels where 33 I/O drive key-matrix scanning, LED indicators, and LCD multiplex control. The RISC core executes branch-light state machines in 200 ns per instruction, letting one MCU poll a 4x5 key matrix, debounce, and refresh an indicator array without timing pressure. Power consumption around 15 µA at 5 V/4 MHz typical keeps standby budgets low for AC-line-derived appliances. OTP code lock protects against firmware cloning.
Рекомендуется
Automotive Body and Chassis Subsystems
With its Extended -40 °C to +125 °C rating and 33 I/O, the PIC16C64A-20E/L is a fit for body controllers, wiper modules, mirror-adjust ECUs, and instrument cluster back-end drivers where automotive EOL parts are common. The OTP EPROM prevents field firmware tampering, while the Harvard RISC core delivers deterministic interrupt response for safety-relevant actuation. Note: this part is not AEC-Q100 qualified in the verified data, so it is typically used in non-safety automotive subsystems rather than critical chassis controllers.
Рекомендуется
Battery-Powered Sensing Nodes
The PIC16C64A-20E/L supports 3 V battery operation at 32 kHz with approximately 1 µA typical supply current, enabling multi-year coin-cell or two-AA-node duty cycles for remote sensors. Its fully static design lets the clock halt between samples without state loss, and its wide 2.5 V to 6.0 V range covers Li coin, alkaline, and regulated 3.3 V rails. 128 bytes RAM stores sampled data between wakes. The OTP program memory is well-matched to sealed sensor housings.
Рекомендуется
Legacy Embedded System Refresh
Engineers maintaining installed PIC16C64A-20E/L-based systems can use the same 44-PLCC footprint to swap in PIC16C65B for active-production lifecycle support. The PIC16C65B preserves the 20 MHz clock and OTP/EPROM architecture while adding timers and updated interrupt structure. This minimizes re-PCB work and lets existing ICSP programming fixtures continue to be used. The migration is suitable for medical-device, industrial-controller, and aerospace ground-support legacy designs.
Рекомендуется
Instrumentation Front-End Controller
The PIC16C64A-20E/L acts as a measurement front-end controller, sequencing analog multiplexers, triggering ADC conversions, and packaging results for host transmission. Its 33 I/O drive parallel display drivers and keyboard scan paths simultaneously. With 20 MHz instruction throughput, it can service a 10 kHz sample loop while refreshing a numeric display without jitter. Extended temperature ensures operation in outdoor instrumentation cabinets. The 3.5 KB OTP fits calibration tables and lookup firmware.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16C64A-20E/L — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16C64A-20/L | PIC16C65B-20/L | PIC16C64A-04/L |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-PLCC | 44-PLCC - same | 44-PLCC - same | 44-PLCC - same |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 4 MHz |
| Program Memory | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP |
| RAM | 128 bytes | 128 bytes | 192 bytes (improved) | 128 bytes |
| Operating Temperature | -40 to +125 °C (Extended) | 0 to +70 °C (Commercial) | 0 to +70 °C (Commercial) | 0 to +70 °C (Commercial) |
| Operating Voltage | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V |
| I/O Pins | 33 | 33 | 33 | 33 |
| Lifecycle Status | NRND | NRND | Active | NRND |
Ключевые отличия
- Extended -40C to +125C temperature grade (против PIC16C64A-20/L)
- Active-production successor available in same footprint (против PIC16C65B-20/L)
- 20 MHz full-speed operation at Extended temp (против PIC16C64A-04/L)
Заметки по проектированию
For reliable 20 MHz operation the PIC16C64A-20E/L requires Vdd of at least 4.0 V; at 2.5 V to 4.0 V the oscillator and instruction pipeline must be derated to lower clock rates. Use an LDO such as MCP1700 to hold Vdd steady. Decouple Vdd/Vss pairs with 100 nF X7R placed within 5 mm of each pin pair, and add a bulk 10 µF tantalum or ceramic cap near the MCU. The 15 µA typical at 5 V/4 MHz figure does not include I/O drive current - budget additional mA for heavily loaded ports.
Place the 44-PLCC socket with pin 1 marker matching the PCB silk-screen. Keep the crystal/oscillator traces short (<10 mm) and guarded by a ground ring to reduce EMI. The MCLR pin needs a 10 kΩ pull-up to Vdd and a 100 nF decoupling cap for reset noise immunity. The ICSP header (RB6/RB7/VDD/VSS/MCLR) should be brought to a 5-pin in-line connector for production programming without removing the MCU from board.
Estimated: at 20 MHz and 5 V supply, each I/O pin toggles every 200 ns, so external loads above 20 pF can cause ring-on transitions - add 33 Ω series resistors on high-fanout signals. Watchdog timer must be cleared in the main loop; software hangs without WDT service will trigger reset every ~18 ms nominal. OTP EPROM cannot be re-programmed - ensure code is fully debugged on a PIC16F equivalent or windowed PIC16C64A JW device before committing to OTP.
Информация о соответствии
RoHS/REACH/lead-free status not confirmed in verified web data; the part uses 44-PLCC package which historically contains lead in PLCC socket options. AEC-Q100 not applicable to legacy 8-bit EPROM microcontrollers; verify with Microchip for any automotive qualification.
