PIC16C67-04/P - 8-Bit 4MHz 14KB OTP MCU 40-PDIP | Microchip
Артикул: PIC16C67-04/P ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $9.27 | $9,27 |
| 10 | $8.45 | $84,50 |
| 100 | $7.62 | $762,00 |
| 500 | $6.95 | $3.475,00 |
| 1.000 | $6.3 | $6.300,00 |
PIC16C67-04/P Обзор
What is a PIC16C6X microcontroller? The PIC16C6X family is a low-cost, high-performance, CMOS, fully-static, 8-bit microcontroller series based on Microchip's PIC RISC architecture. Positioned in the taxonomy, it belongs to the PIC16 mid-range family, which sits between the baseline PIC10/12/16 and the enhanced PIC17/18 architectures; within the broader microcontroller -> embedded MCU -> semiconductor hierarchy, these OTP-EPROM devices serve as one-time programmable alternatives to flash-based PIC16F counterparts, preserving pin-for-pin compatibility with the flash variants.
Key features include a Harvard bus, single-cycle instruction execution at 4 MHz, 14 interrupt sources with on-chip peripherals, an 8-bit successive-approximation ADC with up to eight input channels, a USART for serial communication, and a master SSP supporting both SPI and I2C. The 8-level hardware stack and 15 special-function hardware registers are mapped into the data memory map.
The PIC16C67-04/P uses a low-power, high-speed CMOS EPROM/ROM process with a fully static design that allows the clock to be stopped without losing register state. With a 14-bit instruction word, 8-bit data path, and 200 ns instruction cycle at 4 MHz, it achieves roughly 5 MIPS throughput, which historically was sufficient for motor control, instrumentation, and consumer product designs.
Typical applications include industrial control systems, white goods and appliance controllers, automotive body electronics (pre-CAN era), smart sensor nodes, and battery-powered instrumentation where the 1 µA standby current enables long-life operation. Designers chose this part when code lock or OTP security was preferred over flash reprogrammability.
When designing with the PIC16C67-04/P, plan for OTP programming: code must be verified before production programming because OTP cannot be erased. Always provide a decoupling capacitor within 5 mm of VDD/VDD2 pins and reserve a 4-pin ICSP header for production programming.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для PIC16C67-04/P — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16C67-04/P (тот же форм-фактор и посадочное место) — отличается по Package, Mounting Type, Timers, ADC, Core Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16C67-10/P
✅ Прямая замена✓ В наличии
$3.34 / шт.
Открыть даташит →PIC16C67-20/P
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC16F877A-I/P
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →PIC16F877-04/P
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →PIC16C67-04I/P
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC16F877-20/P
✅ Прямая замена✓ В наличии
$6.2 / шт.
Открыть даташит →PIC16C67-04/P Максимальные параметры и электрические характеристики
| Core Architecture | PIC16C6X RISC, 8-bit |
| Instruction Set | 35 single-word instructions |
| Instruction Word Size | 14-bit |
| Максимальная тактовая частота | 4 MHz |
| Instruction Cycle Time | 200 ns @ 4 MHz |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 14 KB (8K x 14) |
| Data RAM | 368 bytes |
| Data EEPROM | Not included |
| I/O Pins | 33 |
| Operating Voltage Range | 2.5 V to 6.0 V |
| Typical Current 5V/4MHz | 15 µA |
| Typical Current 3V/32kHz | 1 µA |
| ADC | 8-bit, up to 8 channels |
| Communication Peripherals | USART, MSSP (SPI/I2C) |
| Timers | Timer0, Timer1, Timer2 |
| PWM Outputs | Yes (via CCP module) |
| Hardware Stack | 8 levels |
| Корпус | 40-pin PDIP (0.600", 15.24 mm) |
| Тип монтажа | Through-Hole |
| Диапазон рабочих температур | 0°C to +70°C (commercial, this suffix) |
| Статус RoHS | Compliant |
| Lead-Free Finish | Matte Tin (Pb-free) |
Конфигурация выводов PIC16C67-04/P
| Контакт 1 | MCLR/VPP — Master Clear (reset) input / programming voltage |
| Контакт 2 | RA0/AN0 — Port A bit 0 / analog input 0 |
| Контакт 3 | RA1/AN1 — Port A bit 1 / analog input 1 |
| Контакт 4 | RA2/AN2 — Port A bit 2 / analog input 2 |
| Контакт 5 | RA3/AN3/VREF — Port A bit 3 / analog input 3 / ADC reference |
| Контакт 6 | RA4/T0CKI — Port A bit 4 / Timer0 clock input |
| Контакт 7 | RA5/AN4/SS — Port A bit 5 / analog input 4 / SPI slave select |
| Контакт 8 | RE0/RD — Port E bit 0 / parallel slave port read control |
| Контакт 9 | RE1/WR — Port E bit 1 / parallel slave port write control |
| Контакт 10 | RE2/CS — Port E bit 2 / parallel slave port chip select |
| Контакт 11 | VDD — Positive supply (5V typical) |
| Контакт 12 | VSS — Ground |
| Контакт 13 | OSC1/CLKIN — Oscillator input / external clock input |
| Контакт 14 | OSC2/CLKOUT — Oscillator output / clock output |
| Контакт 15 | RC0/T1OSO/T1CKI — Port C bit 0 / Timer1 oscillator output |
| Контакт 16 | RC1/T1OSI/CCP2 — Port C bit 1 / Timer1 oscillator input / CCP2 |
| Контакт 17 | RC2/CCP1 — Port C bit 2 / Capture Compare PWM 1 |
| Контакт 18 | RC3/SCK/SCL — Port C bit 3 / SPI clock / I2C clock |
| Контакт 19 | RD0/PSP0 — Port D bit 0 / parallel slave port data bit 0 |
| Контакт 20 | RD1/PSP1 — Port D bit 1 / parallel slave port data bit 1 |
| Контакт 21 | RD2/PSP2 — Port D bit 2 / parallel slave port data bit 2 |
| Контакт 22 | RD3/PSP3 — Port D bit 3 / parallel slave port data bit 3 |
| Контакт 23 | RC4/SDI/SDA — Port C bit 4 / SPI data in / I2C data |
| Контакт 24 | RC5/SDO — Port C bit 5 / SPI data out |
| Контакт 25 | RC6/TX/CK — Port C bit 6 / USART TX / clock |
| Контакт 26 | RC7/RX/DT — Port C bit 7 / USART RX / data |
| Контакт 27 | RD4/PSP4 — Port D bit 4 / parallel slave port data bit 4 |
| Контакт 28 | RD5/PSP5 — Port D bit 5 / parallel slave port data bit 5 |
| Контакт 29 | RD6/PSP6 — Port D bit 6 / parallel slave port data bit 6 |
| Контакт 30 | RD7/PSP7 — Port D bit 7 / parallel slave port data bit 7 |
| Контакт 31 | VSS — Ground |
| Контакт 32 | VDD — Positive supply (5V typical) |
| Контакт 33 | RB0/INT — Port B bit 0 / external interrupt |
| Контакт 34 | RB1 — Port B bit 1 |
| Контакт 35 | RB2 — Port B bit 2 |
| Контакт 36 | RB3/PGM — Port B bit 3 / low-voltage programming |
| Контакт 37 | RB4 — Port B bit 4 |
| Контакт 38 | RB5 — Port B bit 5 |
| Контакт 39 | RB6/PGC — Port B bit 6 / ICSP clock |
| Контакт 40 | RB7/PGD — Port B bit 7 / ICSP data |
Типичное применение
PIC16C67-04/P подходит для 7 применениеs: Industrial Control Systems, Appliance and White Goods Controllers, Battery-Powered Instrumentation, Automotive Body Electronics (Legacy), Smart Sensor Signal Conditioning, Educational and Hobbyist Development, Point-of-Sale Terminals (Legacy).
Industrial Control Systems
The PIC16C67-04/P fits industrial control because its 33 digital I/O pins drive relays, sensors, and indicator panels directly, while the on-chip 8-bit ADC with eight input channels handles analog transducer signals without external components. At 4 MHz and 5 V, the 200 ns instruction cycle closes control loops in roughly 50 µs, adequate for conveyor sequencing, packaging machinery, and HVAC damper actuators. The 14 KB OTP memory holds complete state machines and lookup tables for PID loops; the USART interfaces to operator panels, while the MSSP supports SPI displays or I2C EEPROM parameter storage.
Рекомендуется
Appliance and White Goods Controllers
White-goods designers chose the PIC16C67-04/P for washing machines, microwave ovens, and dishwasher control boards because its 33 I/O lines drive seven-segment displays, keypad matrices, triac-fired heater loads, and motor direction relays from a single chip. The CCP module generates zero-crossing PWM for universal-motor speed control, and the 8-bit ADC reads temperature sensors (NTC) and water-level probes. Low 15 µA active and 1 µA standby currents help meet standby-power regulations under 1 W, while OTP code-lock prevents unauthorized firmware duplication.
Рекомендуется
Battery-Powered Instrumentation
For portable meters and data loggers, the PIC16C67-04/P's 1 µA typical standby current at 3 V and 32 kHz preserves battery life across months of idle storage; the fully static design lets the RTC wake the MCU only when a measurement is due. The 14-bit instruction word and 8-bit data path execute averaging filters and compression routines comfortably. The 8-channel ADC scans sensor arrays directly, while USART outputs to Bluetooth or IrDA modules. OTP code-lock prevents cloning of calibration data, a security advantage over flash parts.
Рекомендуется
Automotive Body Electronics (Legacy)
Pre-CAN-era automotive body modules used the PIC16C67-04/P for central door locking, seat-memory, and lighting control because the 33 I/O lines and 8-bit ADC read switch panels and drive MOSFET bridges directly. The wide 2.5-6.0 V supply tolerance survives load-dump events, and the 4 MHz core performs timing sequences well within automotive latency budgets. The on-chip USART links to dashboard indicators, while the MSSP talks to dashboard LCDs in SPI mode. New designs should migrate to AEC-Q100 qualified PIC16F877A or PIC18F variants.
Рекомендуется
Smart Sensor Signal Conditioning
Sensor hubs and transmitter boards use the PIC16C67-04/P to digitize thermocouple, strain-gauge, or pressure-bridge signals via the 8-bit ADC, apply linearization in firmware, and output either a 4-20 mA current loop or a Modbus RTU stream over the USART. The 14 KB OTP holds calibration tables for up to 32 sensor types. The MSSP drives I2C temperature compensation chips or SPI DACs. Brown-out reset and watchdog timer ensure reliable recovery from supply transients in field installations.
Рекомендуется
Educational and Hobbyist Development
Universities and hobbyists adopted the PIC16C67-04/P as a teaching vehicle because the 40-pin PDIP is breadboard-friendly and the PIC16 mid-range instruction set (only 35 instructions) is approachable. MPLAB IDE and the PICSTART Plus programmer support the part, with the ICSP header enabling solderless re-programming during labs (note: OTP cannot be erased, so each code change requires a fresh chip in production hardware but EPROM-windowed JW parts exist for development). The variety of peripherals - ADC, USART, SPI, I2C, PWM - teaches nearly every embedded concept in one chip.
Рекомендуется
Point-of-Sale Terminals (Legacy)
Pre-EMV-era POS terminals leveraged the PIC16C67-04/P for keypad scanning, LCD driving via SPI, magnetic-stripe reader interface through USART, and thermal printer control via CCP/PWM. The 33 I/O lines handle the entire I/O matrix without external logic. OTP code-lock protects proprietary payment protocols. Today's designers should choose PIC16F877A or PIC18F family for new POS hardware, but the PIC16C67 remains in service for legacy terminal refurbishment.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16C67-04/P — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16C67-10/P | PIC16C67-20/P | PIC16F877A-I/P | PIC16F877-04/P | PIC16C67-04I/P |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-PDIP (0.600 inch) | 40-PDIP (0.600 inch) - same | 40-PDIP (0.600 inch) - same | 40-PDIP (0.600 inch) - same | 40-PDIP (0.600 inch) - same | 40-PDIP (0.600 inch) - same |
| Program Memory Type | OTP EPROM | OTP EPROM | OTP EPROM | Flash | Flash | OTP EPROM |
| Program Memory Size | 14 KB (8K x 14) | 14 KB | 14 KB | 14 KB | 14 KB | 14 KB |
| Max Clock Frequency | 4 MHz | 10 MHz | 20 MHz | 20 MHz | 4 MHz | 4 MHz |
| Data RAM | 368 bytes | 368 bytes | 368 bytes | 368 bytes | 368 bytes | 368 bytes |
| I/O Pins | 33 | 33 | 33 | 33 | 33 | 33 |
| Operating Temperature Range | 0°C to +70°C (commercial) | 0°C to +70°C (commercial) | 0°C to +70°C (commercial) | -40°C to +85°C (industrial) | 0°C to +70°C (commercial) | -40°C to +85°C (industrial) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Active | Obsolete | Obsolete |
Ключевые отличия
- OTP code-lock security vs flash reprogrammability (против PIC16F877A-I/P)
- Drop-in higher-speed same-family upgrade (против PIC16C67-10/P)
- Wider commercial-to-industrial temperature option in same family (против PIC16C67-04I/P)
Заметки по проектированию
OTP memory cannot be erased electrically. Once a PIC16C67-04/P is programmed, the only way to change the firmware is to physically replace the chip. Always fully verify code with a JW (windowed) or flash development part before programming production OTP units. Build a small rework budget into your BoM for engineering samples. Because OTP parts can be programmed only once, field firmware updates are impossible - if your product has any post-deployment update requirement, migrate to PIC16F877A instead.
Place a 0.1 µF ceramic decoupling capacitor within 5 mm of each VDD/VSS pin pair (pins 11/12 and 31/32). For noisy environments, add a bulk 10 µF tantalum or aluminum electrolytic capacitor at the board power entry. The PIC16C67-04/P supply range is 2.5 V to 6.0 V; brown-out reset should be enabled in the configuration word to protect against code corruption during supply droops below 4.0 V at 5 V nominal operation.
Reserve a 5-pin ICSP header (VPP/MCLR, PGD, PGC, VDD, VSS) on every production board even if you use OTP. This allows programming during board test and field recovery. For the 40-pin PDIP, position the ICSP connector near pins 1, 39, and 40 to keep the ICSP signals short. Use a 4.7 kΩ pull-up on MCLR to VDD through a diode for proper reset behavior during programming.
Keep the crystal/oscillator traces short (under 10 mm) and surround them with a ground guard ring on both sides of the PCB. For 4 MHz operation a fundamental-mode AT-cut crystal with 20 pF load capacitors is typical. When using the internal RC oscillator (PIC16C67-04/P supports this), verify that timing-critical peripherals like USART can tolerate the +/- 1% to +/- 5% RC tolerance before committing to the design.
Информация о соответствии
RoHS compliance per Microchip product page lead-free matte-tin finish. Not AEC-Q100 qualified (PIC16C family is not automotive grade); AEC-Q100 users must select PIC16F or PIC18 equivalents. REACH and conflict-mineral statements should be requested from Microchip directly via the official compliance letter program.
