PIC16LF1503T-I/SL - 8-Bit MCU 20MHz 3.5KB Flash 14-SOIC
Артикул: PIC16LF1503T-I/SL ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.05 | $1,05 |
| 10 | $0.98 | $9,80 |
| 100 | $0.92 | $92,00 |
| 500 | $0.85 | $425,00 |
| 1.000 | $0.79 | $790,00 |
| 2.600 | $0.74 | $1.924,00 |
PIC16LF1503T-I/SL Обзор
An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, integrating a CPU, volatile RAM, non-volatile program memory (Flash), and peripherals on one die. Within the broader hierarchy, this device belongs to PIC microcontrollers > 8-bit MCU > microcontroller > embedded processor > semiconductor. PIC16F/LF parts combine a RISC Harvard architecture with deterministic interrupt handling, making them a foundation for cost-sensitive and low-power embedded designs.
Key features include 20 MHz CPU speed with single-cycle instruction execution, 4 hardware timers (Timer0, Timer1, Timer2), a 10-bit ADC with multiple acquisition channels, CWG for complementary MOSFET drive, NCO for fine-frequency synthesis without a PLL, and CLC for combinational/sequential logic implementing glue functions in hardware. The 1.8V minimum supply supports battery-operated systems, and ultra-low power sleep modes preserve battery life.
The architecture uses a 14-bit instruction word with separate code and data buses (Harvard), enabling simultaneous instruction fetch and data access. The XLP technology delivers sub-uA sleep currents, supporting designs such as energy-harvesting nodes where the MCU spends most of its time in Sleep.
Typical applications include consumer appliance controls, LED lighting controllers, sensor signal conditioning nodes, low-cost IoT end nodes, and battery-powered handheld devices. The combination of NCO and CLC enables frequency generation and custom digital logic without external components.
When designing with this device, configure the ADC reference and acquisition time carefully; an inadequate acquisition time introduces nonlinearity. Use CLC and NCO to offload repetitive tasks from the CPU and reduce wake frequency, optimizing average power.
This page synthesizes distributor pricing, drop-in alternatives, application examples, and design notes beyond the manufacturer datasheet.
Аналоги без доработки для PIC16LF1503T-I/SL — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16LF1503T-I/SL (тот же форм-фактор и посадочное место) — отличается по Package, ADC, Core Architecture, Operating Temperature, Timers.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16LF1503-I/SL
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC16LF1503-I/P
✅ Прямая замена✓ В наличии
$0.66 / шт.
Открыть даташит →PIC16LF1503-E/SL
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$0.62 / шт.
Открыть даташит →PIC16LF1503T-E/SL
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
PIC16F1503-I/SL
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$0.59 / шт.
Открыть даташит →PIC16LF1503T-I/SL Максимальные параметры и электрические характеристики
| Core Architecture | 8-bit PIC |
| CPU Frequency | 20 MHz |
| Program Memory | 3.5 KB (2K x 14) Flash |
| RAM | 128 bytes |
| Operating Voltage Range | 1.8 V to 3.6 V |
| I/O Pins | 12 |
| ADC | 10-bit |
| Timers | 4 (Timer0, Timer1, Timer2, WDT) |
| Peripheral Modules | CLC, CWG, NCO |
| Корпус | 14-SOIC (0.150 inch) |
| Тип монтажа | Surface Mount |
| Рабочая температура | -40 C to +85 C |
| Packing Media | Tape and Reel (2600) |
| Lead Count | 14 |
| Статус RoHS | Compliant |
Конфигурация выводов PIC16LF1503T-I/SL
| Контакт 1 | RA5/!MCLR/VPP — RA5 GPIO / !MCLR reset / VPP programming voltage |
| Контакт 2 | RA0 — PORTA I/O; analog input |
| Контакт 3 | RA1 — PORTA I/O; analog input |
| Контакт 4 | RA2 — PORTA I/O; analog input |
| Контакт 5 | RA3 — PORTA I/O / !MCLR (alt mode); analog input |
| Контакт 6 | RA4 — PORTA I/O; analog input |
| Контакт 7 | VSS — Ground reference |
| Контакт 8 | RC0 — PORTC I/O |
| Контакт 9 | RC1 — PORTC I/O |
| Контакт 10 | RC2 — PORTC I/O |
| Контакт 11 | RC3 — PORTC I/O |
| Контакт 12 | RC4 — PORTC I/O |
| Контакт 13 | RC5 — PORTC I/O |
| Контакт 14 | VDD — Positive supply voltage (1.8V-3.6V) |
Типичное применение
PIC16LF1503T-I/SL подходит для 6 применениеs: Consumer Appliance Control, LED Lighting Controller, IoT Sensor End Node, Battery-Powered Handheld Device, Sensor Signal Conditioning Node, Hobbyist/Educational MCU Board.
Consumer Appliance Control
Low-cost 8-bit MCU with 3.5 KB Flash, 128 B RAM, and 12 GPIO handles user-input scanning, sensor acquisition, and PID-driven heater or motor control. Operating from 1.8V to 3.6V, it supports single-cell Li-ion or DC rectified supplies and XLP sleep currents below 1 uA. Used in kitchen timers, water heaters, and small appliance HMI.
Рекомендуется
LED Lighting Controller
The CWG outputs drive complementary MOSFETs for LED strings, while the 10-bit ADC handles analog dimming through a sense resistor. A/D conversions plus CLC-accomplished PWM correction remove external gate driver ICs, and XLP sleep adds energy-harvesting compatibility. The 14-SOIC 0.150 inch package fits compact bulb form factors.
Рекомендуется
IoT Sensor End Node
Three GPIO-free timers and 128 B RAM cover periodic sensor reads with sub-uA sleep, well-matched to coin-cell remote controls, PIR-driven sensors, and RF wake-link front-ends. The NCO generates 16-kHz wake ticks without waking the CPU, and the 10-bit ADC supports voltage-, RTD-, or thermistor-based measurements.
Рекомендуется
Battery-Powered Handheld Device
The 1.8V minimum supply and XLP sleep support multi-year coin-cell runtime in remote controls or asset tags. The CLC plus NCO deliver chirp and wake signals without external parts, allowing low BOM cost. The 14-SOIC 0.150 inch package streams cleanly through wave/solder reflow.
Рекомендуется
Sensor Signal Conditioning Node
Twelve GPIO plus 10-bit ADC read resistive, voltage, and temperature sensors. The NCO synthesizes excitation signals for AC-bridge conditioning, while the CLC implements digital filters in hardware. This pairing reduces the BOM compared with op-amp + external logic designs in industrial and metering applications.
Рекомендуется
Hobbyist/Educational MCU Board
With 14 GPIO and 20 MHz, the PIC16LF1503T-I/SL is well-suited as an entry-level MCU on breadboard modules. Its instruction-set compatibility with PICkit and MPLAB X IDE lowers learning barriers, and its 14-SOIC 0.150 inch package fits DIP-adapter boards. Embedded-systems learners use it for timer interrupts, ADC, and CLC exercises.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16LF1503T-I/SL — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16LF1503-I/SL | PIC16LF1503-I/P | PIC16LF1503-E/SL | PIC16LF1503T-E/SL | PIC16F1503-I/SL |
|---|---|---|---|---|---|---|
| Package | 14-SOIC (0.150 in) | 14-SOIC (same) | 14-SOIC (same) | 14-SOIC (same) | 14-SOIC (same) | 14-SOIC (same) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 3.5 KB Flash | 3.5 KB Flash | 3.5 KB Flash | 3.5 KB Flash | 3.5 KB Flash | 3.5 KB Flash |
| Operating Voltage | 1.8V to 3.6V | 1.8V to 3.6V | 1.8V to 3.6V | 1.8V to 3.6V | 1.8V to 3.6V | 1.8V to 5.5V (wider) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +125C (extended) | -40C to +125C (extended) | -40C to +85C |
| Packing Media | Tape and Reel (2600) | Tube (no 'T') | Tube / PDIP | Tube | Tape and Reel | Tube / SOIC |
| GPIO Count | 12 | 12 | 12 | 12 | 12 | 12 |
| XLP Low-Power | Yes (1.8V min) | Yes | Yes | Yes | Yes | No (5.5V max) |
Ключевые отличия
- Same-brand drop-in alternative with industrial -40C to +125C rating (против PIC16LF1503-E/SL)
- Lowest-voltage variant in the family (против PIC16F1503-I/SL)
- Tape-and-reel packing for high-volume assembly (против PIC16LF1503-I/SL)
Заметки по проектированию
Place VDD/VSS decoupling as close to pins 14 and 7 of the 14-SOIC as practical. Estimated: a 100 nF X7R ceramic bypass reduces digital-switching voltage excursions. Add a bulk capacitor of at least 1 uF near VDD if the supply is shared with motor or LED drivers.
For battery-operated designs, drive the device from a 1.8V LDO rather than a switching regulator. Estimated: an LDO paired with the XLP sleep-mode current keeps quiescent draw below 2 uA over a 3.3V cell. Use !MCLR tied to VDD via 10 kohm resistor for clean reset edge.
Ensure the !MCLR/VPP pin configuration is correct; using !MCLR as GPIO requires configuration-word changes that may lock out in-circuit programming. Avoid using the PIC16F1503 as a cross-package substitute; verify the package suffix (-SL, -ST, -P, -MG) before substitution.
Информация о соответствии
RoHS and lead-free compliant per Microchip product page. Country of origin: Thailand. AEC-Q100 not applicable (not the -Q1 automotive suffix).
