PIC16LF1787T-I/MV - 8-bit MCU 32MHz 14KB Flash | Microchip
Артикул: PIC16LF1787T-I/MV ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.95 | $2,95 |
| 10 | $2.66 | $26,60 |
| 100 | $2.37 | $237,00 |
| 500 | $2.13 | $1.065,00 |
| 1.000 | $1.91 | $1.910,00 |
PIC16LF1787T-I/MV Обзор
An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that integrates CPU, Flash, RAM, EEPROM, and peripherals. The PIC16 family occupies the mid-range PIC segment, sitting above baseline (PIC10/PIC12/PIC16F5x) and below the PIC18/dsPIC families. MCU -> PIC16 family -> PIC16LF178x sub-family -> PIC16LF1787 specific device, with the "LF" suffix and "nWLP/XLP" branding indicating Microchip's nanoWatt eXtreme Low Power technology for sleep currents in the sub-uA range.
Key features include 8 K x 14 Flash (14 KB), 1 KB RAM, 256 B EEPROM, the afore-mentioned 12-bit ADC and 8-bit DAC, OPAmp modules, three PSMC channels providing flexible PWM with programmable frequency, duty cycle, and dead-band control, plus standard peripherals (CCP, EUSART, I2C, SPI, comparators). Connectivity is I2C/SPI/UART on 35 I/O pins. Supply voltage spans 1.8 V to 3.6 V (LF "low-voltage/frequency" part).
Designers should note the UQFN-EP exposed pad must be soldered to the PCB ground plane for thermal dissipation; operating temperature range is -40 °C to +85 °C (industrial, "I" suffix). The PSMC peripheral differentiates this MCU from standard CCP timers by allowing digital feedback control of PWM frequency and pulse begin/end times. When migrating firmware, the PSMC registers and trigger sources differ from dsPIC PWM modules - check the
Note: datasheet for register maps and the "Migrating from PIC16F1787" application note (refer to manufacturer documentation).
Typical applications include LED lighting drivers (using PSMC for high-resolution dimming), Switch-mode power supply controllers, motor control (brushed DC up to 1.5 A drive via the integrated OPAmp + PSMC), battery-powered IoT sensor nodes (nWLP/XLP sleep modes), and small appliance control panels. The wide Vdd range and integrated analog make it a strong fit for mixed-signal designs that need to minimize external components.
When designing with this device, the LF variant requires the 32 MHz internal oscillator to be used carefully - check the factory calibration value in the OSCTUNE register for temperature compensation. Total I/O count is 35 across a 40-pin package; the remaining pins are dedicated to Vdd/Vss and the EP. Plan pin allocation early, especially when assigning analog functions (AN0-ANxx) and the dedicated OPAmp input pins.
Аналоги без доработки для PIC16LF1787T-I/MV — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC16LF1787T-I/MV (тот же форм-фактор и посадочное место) — отличается по Package, Program Memory (Flash), DAC, ADC, Core Architecture.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC16LF1786T-I/MV
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
PIC16LF1784T-I/MV
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$1.74 / шт.
Открыть даташит →PIC16LF1782T-I/MV
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$1.55 / шт.
Открыть даташит →PIC16F1787T-I/MV
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$2.1 / шт.
Открыть даташит →PIC16LF1787-E/MV
✅ Прямая замена✓ В наличии
$2.61 / шт.
Открыть даташит →PIC16LF1787-I/MV
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
PIC16LF1787T-I/MV Максимальные параметры и электрические характеристики
| Core Architecture | 8-bit PIC RISC |
| Family | PIC16LF178x (PIC16F1787 core, low-voltage "LF" variant) |
| Program Memory (Flash) | 14 KB (8 K x 14 words) |
| Data RAM | 1 KB |
| EEPROM | 256 bytes |
| Maximum CPU Speed | 32 MHz |
| Supply Voltage (Vdd) | 1.8 V to 3.6 V |
| Number of I/O Pins | 35 |
| ADC | 12-bit |
| DAC | 8-bit |
| Operational Amplifiers | Yes (integrated OPAmp modules) |
| PSMC Channels | 3 (Programmable Switch Mode Controller) |
| Communication Interfaces | I2C, SPI, EUSART (UART) |
| Рабочая температура | -40 °C to +85 °C (Industrial, "I") |
| Корпус | 40-pin UQFN-EP, 5x5 mm |
| Тип монтажа | Surface Mount |
| Low-Power Technology | nanoWatt XLP (nWXLP) |
| Статус RoHS | Compliant |
Конфигурация выводов PIC16LF1787T-I/MV
| Контакт 1 | RA0/AN0/C1IN0-/DAC/OPA1IN+ — PORTA bit 0 / Analog input / Comparator input / DAC output / OPAmp1 input |
| Контакт 2 | RA1/AN1/C1IN1- — PORTA bit 1 / Analog input 1 / Comparator input |
| Контакт 3 | RA2/AN2 — PORTA bit 2 / Analog input 2 |
| Контакт 4 | RA3/AN3/C1IN1+ — PORTA bit 3 / Analog input 3 / Comparator non-inverting input |
| Контакт 5 | RA4/AN4/C2OUT — PORTA bit 4 / Analog input 4 / Comparator 2 output |
| Контакт 6 | RA5/AN5 — PORTA bit 5 / Analog input 5 |
| Контакт 7 | RA6 — PORTA bit 6 |
| Контакт 8 | RA7 — PORTA bit 7 |
| Контакт 9 | VSS — Ground reference |
| Контакт 10 | VDD — Positive supply (1.8 V to 3.6 V) |
| Контакт 11 | RB0/INT — PORTB bit 0 / External interrupt |
| Контакт 12 | RB1 — PORTB bit 1 |
| Контакт 13 | RB2 — PORTB bit 2 |
| Контакт 14 | RB3 — PORTB bit 3 |
| Контакт 15 | RB4 — PORTB bit 4 |
| Контакт 16 | RB5 — PORTB bit 5 |
| Контакт 17 | RB6/ICSPCLK — PORTB bit 6 / ICSP clock |
| Контакт 18 | RB7/ICSPDAT — PORTB bit 7 / ICSP data |
| Контакт 19 | VSS — Ground |
| Контакт 20 | VDD — Positive supply |
| Контакт 21 | RC0 — PORTC bit 0 |
| Контакт 22 | RC1 — PORTC bit 1 |
| Контакт 23 | RC2 — PORTC bit 2 |
| Контакт 24 | RC3 — PORTC bit 3 |
| Контакт 25 | RC4 — PORTC bit 4 |
| Контакт 26 | RC5 — PORTC bit 5 |
| Контакт 27 | RC6 — PORTC bit 6 |
| Контакт 28 | RC7 — PORTC bit 7 |
| Контакт 29 | VSS — Ground |
| Контакт 30 | VDD — Positive supply |
| Контакт 31 | RD0 — PORTD bit 0 |
| Контакт 32 | RD1 — PORTD bit 1 |
| Контакт 33 | RD2 — PORTD bit 2 |
| Контакт 34 | RD3 — PORTD bit 3 |
| Контакт 35 | RD4 — PORTD bit 4 |
| Контакт 36 | RD5 — PORTD bit 5 |
| Контакт 37 | RD6 — PORTD bit 6 |
| Контакт 38 | RD7 — PORTD bit 7 |
| Контакт 39 | RE0 — PORTE bit 0 |
| Контакт 40 | RE1 — PORTE bit 1 |
| Контакт EP | EP — Exposed thermal pad - must be soldered to grounded copper pour |
Типичное применение
PIC16LF1787T-I/MV подходит для 6 применениеs: LED Lighting Driver with PSMC Dimming, Switch-Mode Power Supply (SMPS) Controller, Battery-Powered IoT Sensor Node, Small Appliance Control Board (Coffee Machine, Mixer), Closed-Loop Sensor Conditioning Hub, Automotive Interior Lighting/Mirror Module.
LED Lighting Driver with PSMC Dimming
The PIC16LF1787T-I/MV's three PSMC channels drive high-resolution PWM dimming of LED strings, replacing an external PWM controller IC. The 32 MHz core and 12-bit ADC enable closed-loop current control at >200 kHz PWM frequencies, which eliminates audible flicker in constant-current LED drivers. Running from 1.8 V-3.6 V, this device fits battery and USB-powered LED lamps, and the nanoWatt XLP sleep modes reduce standby current below 1 uA to meet stringent energy-star standby budgets when the lamp is off.
Рекомендуется
Switch-Mode Power Supply (SMPS) Controller
The PIC16LF1787T-I/MV delivers full SMPS functionality with its three PSMC channels, providing programmable frequency, duty cycle, rising/falling dead-band, and hardware fault shutdown. The integrated OPAmp modules configure as the current-sense amplifier directly, eliminating an external op-amp. The 12-bit ADC samples Vout for digital feedback regulation. This single-chip SMPS approach cuts BOM cost and PCB area in AC/DC adapters, isolated DC/DC converters, and battery chargers up to ~50 W.
Рекомендуется
Battery-Powered IoT Sensor Node
The PIC16LF1787T-I/MV runs from 1.8 V-3.6 V with nanoWatt XLP sleep current below 1 uA in doze/idle modes, making it ideal for coin-cell or 2xAA battery sensor nodes. Its 12-bit ADC reads analog sensors (temperature, light, gas) and its I2C/SPI/EUSART interfaces connect to digital sensors. Compact 5x5 mm UQFN-EP footprint minimizes PCB area for wearable or smart-home sensor tags. Combined with its 14 KB Flash, the device runs custom firmware plus protocol stacks (e.g., Modbus or proprietary RF command sets).
Рекомендуется
Small Appliance Control Board (Coffee Machine, Mixer)
The PIC16LF1787T-I/MV's integrated OPAmp + DAC + ADC subsystems replace multiple discrete components in small appliances. The PSMC channels drive TRIAC or MOSFET gate drivers for motor speed control (low-V brushes) while CCP/EUSART control user keypads/buttons. Its wide 1.8 V-3.6 V Vdd simplifies power-rail selection in 2xAA designs, and its industrial temperature range (-40 to +85 °C) covers kitchen and garage deployments. This consolidates the BOM into a single MCU in coffee makers, blenders, and similar appliances.
Рекомендуется
Closed-Loop Sensor Conditioning Hub
The PIC16LF1787T-I/MV integrates 12-bit ADC, 8-bit DAC, and OPAmp modules that close the loop on analog sensors, eliminating external signal-chain components. The 8-bit DAC provides offset or excitation to bridge-type sensors while the OPAmp gain-stages the signal and the ADC digitizes the result. The 35 I/O pins support multi-channel sensor matrices (e.g., 4-wire RTD, strain gauge), and EUSART provides reliable wired connectivity in factory automation or HVAC applications.
Рекомендуется
Automotive Interior Lighting/Mirror Module
Although not AEC-Q100 qualified at this variant, the PIC16LF1787T-I/MV can be used in non-safety automotive interior subsystems like ambient lighting or rear-view mirror modules. Its PSMC channels drive RGB LEDs with smooth cross-fades and the wide Vdd range tolerates 12 V battery transients when paired with an external regulator. The compact 5x5 mm UQFN-EP footprint eases integration into slim mirror housings, and its 12-bit ADC senses ambient light to set adaptive brightness.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC16LF1787T-I/MV — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC16LF1786T-I/MV | PIC16LF1784T-I/MV | PIC16LF1782T-I/MV | PIC16F1787T-I/MV |
|---|---|---|---|---|---|
| Package | 40-pin UQFN-EP (5x5 mm) | 40-pin UQFN-EP (5x5 mm) - same | 40-pin UQFN-EP (5x5 mm) - same | 40-pin UQFN-EP (5x5 mm) - same | 40-pin UQFN-EP (5x5 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 14 KB | 14 KB (full size variant of family) | 7 KB | 3.5 KB | 14 KB |
| Data RAM | 1 KB | 1 KB | 512 B | 256 B | 1 KB |
| EEPROM | 256 B | 256 B | 256 B | 256 B | 256 B |
| Maximum CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Supply Voltage (Vdd) | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 5.5 V |
| I/O Pins | 35 | 35 | 35 | 35 | 35 |
| PSMC Channels | 3 | 3 | 3 | 3 | 3 |
| Low-Power Technology | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP (XLP family branding) |
Ключевые отличия
- Three PSMC channels with programmable dead-band and fault shutdown (против PIC16LF1786T-I/MV)
- Integrated OPAmp + 8-bit DAC + 12-bit ADC reduces external components (против PIC16LF18857)
- Wide Vdd 1.8 V to 3.6 V matches battery-powered designs (против PIC16F1787T-I/MV)
Заметки по проектированию
The 40-pin UQFN-EP package's exposed thermal pad MUST be soldered to a grounded copper pour (minimum 1 square inch of 1 oz copper on the top layer) to meet the device's thermal envelope. Without the EP soldered, the junction-to-ambient thermal resistance (theta_JA) rises dramatically and the silicon die can overheat even at moderate ambient loads. Use thermal vias under the EP to inner/ground layers for additional heat spreading; this is critical when running full CPU speed at 32 MHz with active peripherals.
Place the bulk Vdd decoupling capacitor (4.7 uF or 10 uF ceramic) within 5 mm of the Vdd pins and a 100 nF ceramic cap within 2 mm of each Vdd pin. The PIC16LF1787 has multiple Vdd/Vss pairs around the package - each pair needs its own bypass capacitor. Route analog signals (ANx, DAC, OPAmp inputs) far from high-current digital traces and from the PSMC PWM outputs to avoid analog coupling. Place the ICSP clock/data (RB6/RB7) on dedicated test pads if you plan to use in-circuit programming.
When migrating firmware across the PIC16LF178x family (1787 -> 1786 -> 1784 -> 1782), be aware that the Flash map and RAM allocation are different; re-validate linker scripts against the target device's data sheet, not just the family overview. Also confirm the 32 MHz internal oscillator's OSCTUNE factory calibration is within the device's operating range - LF parts have a different calibration profile than F parts. Finally, the PSMC module's output polarity, dead-band, and fault-shutdown behavior differ from generic dsPIC PWM; check the PIC16L(F)1787 datasheet (DS40001874D) PSMC section before re-using code from another MCU.
Информация о соответствии
RoHS and lead-free per Microchip's UQFN family. Not AEC-Q100 qualified; for automotive applications requiring qualification, contact Microchip for PIC16LF1787T-QML or use a different AEC-Q100 qualified PIC16 variant. REACH SVHC status should be confirmed per the latest Microchip declaration.
